• There are no items in your cart

ASTM D 3841 : 2016 : REDLINE

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Glass-Fiber-Reinforced Polyester Plastic Panels
Available format(s)

PDF

Superseded date

05-24-2021

Language(s)

English

Published date

05-01-2016

CONTAINED IN VOL. 08.03, 2016 Defines the classification, materials of construction, workmanship, minimum physical requirements, and methods of testing glass-fiber reinforced polyester plastic panels intended for use in construction.

1.1This specification covers the classification, materials of construction, workmanship, minimum physical requirements, and methods of testing glass-fiber reinforced polyester plastic panels intended for use in construction. Panels for specialized or unique applications have the potential to require values significantly above or below those stated in this specification. Recommended practices for certain specific applications are included as Appendix X1. This specification is not intended to restrict or limit technological changes affecting performance when those changes are agreed upon between the purchaser and the seller.

1.2Supplementary information on chemical resistance, resistance to heat, and installation practices are provided in Appendix X1.

1.3The classification of these plastic panels into types based on relative response to a laboratory test shall not be considered a fire hazard classification.

1.4The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

1.5The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in Tables and Figures) shall not be considered as requirements of this standard.

1.6Fire properties are determined by using laboratory flammability tests (Test Methods D635, D1929, and E84).

1.6.1This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products or assemblies under actual fire conditions.

1.6.2Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.

1.7The following precautionary caveat pertains only to the test method portion, Section 8 of this specification. This specification does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this specification to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1:There is no known ISO equivalent to this standard.

Committee
D 20
DocumentType
Redline
Pages
8
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

CTI STD 131 : 2009 FIBERGLASS-REINFORCED PLASTIC PANELS
CSA S806: 2012 DESIGN AND CONSTRUCTION OF BUILDING STRUCTURES WITH FIBRE-REINFORCED POLYMERS
S806-12 (R2017) Design and construction of building structures with fibre-reinforced polymers

ASTM E 631 : 2015 : REDLINE Standard Terminology of Building Constructions
ASTM D 618 : 2013 : REDLINE Standard Practice for Conditioning Plastics for Testing
ASTM D 1929 : 2016 : REDLINE Standard Test Method for Determining Ignition Temperature of Plastics
ASTM D 4364 : 2013 : REDLINE Standard Practice for Performing Outdoor Accelerated Weathering Tests of Plastics Using Concentrated Sunlight
ASTM E 72 : 2015 : REDLINE Standard Test Methods of Conducting Strength Tests of Panels for Building Construction
ASTM E 903 : 2012 Standard Test Method for Solar Absorptance, Reflectance, and Transmittance of Materials Using Integrating Spheres
ASTM D 1435 : 2013 : REDLINE Standard Practice for Outdoor Weathering of Plastics
ASTM D 696 : 2016 : REDLINE Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between −30°C and 30°C with a Vitreous Silica Dilatometer
ASTM D 790 : 2017 : REDLINE Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
ASTM G 155 : 2013 : REDLINE Standard Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials
ASTM G 147 : 2017 : REDLINE Standard Practice for Conditioning and Handling of Nonmetallic Materials for Natural and Artificial Weathering Tests
ASTM D 570 : 1998 : R2018 Standard Test Method for Water Absorption of Plastics
ASTM D 638 : 2014 : REDLINE Standard Test Method for Tensile Properties of Plastics
ASTM D 3892 : 2015 : REDLINE PRACTICE FOR PACKAGING/PACKING OF PLASTICS

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.