Customer Support: +1 416-401-8730

Login to i2i Subscription Intertek.com
  • There are no items in your cart
Please enter a keyword to search
Advanced search

ASTM D 4027 : 1998

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Measuring Shear Properties of Structural Adhesives by the Modified-Rail Test
Available format(s)

Hardcopy , PDF

Superseded date

11-11-2014

Language(s)

English

Published date

05-10-1998

Publisher

American Society for Testing and Materials

CONTAINED IN VOL. 15.06, 2015 Specifies equipment and procedures to measure the shear modulus and shear strength of adhesive layers between rigid adherends.

1.1 This test method describes equipment and procedures to measure the shear modulus and shear strength of adhesive layers between rigid adherends. The equipment may also be used for determining the adhesive's shear creep compliance, the effects of strain history such as cyclic loading upon shear properties, and a failure criteria for biaxial stress conditions such as shear plus tension and shear plus compression.

1.2 High-density wood shall be the preferred substrate. The practical upper limit on the shear modulus that can be measured is determined by the shear modulus of the adherends and by the strain measuring device. Thus, the practical limit of adhesive shear modulus that can be measured using high-density wood adherends is about 1 X 10 psi (690 MPa).

Note 1-Wood-base composites, metal, plastic, reinforced plastics, and other common construction materials may also be used for adherends.

1.3 The range of specimen dimensions that can be tested are: width 0.0625 to 0.500 in. (1.59 to 12.70 mm), length 4 to 8 in. (102 to 203 mm), and adherend thickness 0.50 to 1.00 in. (13 to 25 mm). The standard specimen dimensions shall be: width 0.125 in. (3.18 mm), length 8 in. (203 mm), and adherend thickness 0.75 in. (19 mm). Bondline thicknesses from 0.006 to 0.125 in. (0.15 to 3.18 mm) may be tested.

1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
D 14
DocumentType
Test Method
Pages
8
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

ASTM D 4896 : 2001 : R2016 Standard Guide for Use of Adhesive-Bonded Single Lap-Joint Specimen Test Results
ASTM D 907 : 2015 : REDLINE Standard Terminology of Adhesives
ASTM D 4896 : 2001 Standard Guide for Use of Adhesive-Bonded Single Lap-Joint Specimen Test Results
ASTM D 6465 : 1999 : R2005 Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants
ASTM D 5574 : 1994 : R1999 : EDT 1 Standard Test Methods for Establishing Allowable Mechanical Properties of Wood-Bonding Adhesives for Design of Structural Joints
ASTM D 5574 : 1994 : R2012 Standard Test Methods for Establishing Allowable Mechanical Properties of Wood-Bonding Adhesives for Design of Structural Joints
ASTM D 5574 : 1994 : R2005 Standard Test Methods for Establishing Allowable Mechanical Properties of Wood-Bonding Adhesives for Design of Structural Joints
ASTM D 907 : 2015 Standard Terminology of Adhesives
ASTM D 6465 : 1999 : R2012 Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants
ASTM D 4896 : 2001 : R2008 : EDT 1 Standard Guide for Use of Adhesive-Bonded Single Lap-Joint Specimen Test Results
ASTM D 6465 : 1999 Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants
ASTM D 6465 : 1999 : R2016 Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants
ASTM E 1420 : 1991 Practice for Specifying Polymeric Materials for Service in Ionizing Radiation Environments (Withdrawn 1996)

ASTM E 83 : 2016 : REDLINE Standard Practice for Verification and Classification of Extensometer Systems
ASTM D 4442 : 2016 : REDLINE Standard Test Methods for Direct Moisture Content Measurement of Wood and Wood-Based Materials
ASTM D 907 : 2015 : REDLINE Standard Terminology of Adhesives
ASTM E 229 : 1997 Standard Test Method for Shear Strength and Shear Modulus of Structural Adhesives (Withdrawn 2003)
ASTM D 905 : 2008 Standard Test Method for Strength Properties of Adhesive Bonds in Shear by Compression Loading

View more information
US$75.00
Excluding Tax where applicable
USD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us