• There are no items in your cart

ASTM D 5026 : 2015

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Plastics: Dynamic Mechanical Properties: In Tension
Available format(s)

Hardcopy , PDF

Superseded date

11-24-2023

Language(s)

English

Published date

07-20-2015

This test method outlines the use of dynamic mechanical instrumentation for gathering and reporting the viscoelastic properties of thermoplastic and thermosetting resins and composite systems in the form of rectangular specimens molded directly or cut from sheets, plates, or molded shapes

1.1This test method outlines the use of dynamic mechanical instrumentation for gathering and reporting the viscoelastic properties of thermoplastic and thermosetting resins and composite systems in the form of rectangular specimens molded directly or cut from sheets, plates, or molded shapes. The tensile data generated may be used to identify the thermomechanical properties of a plastic material or composition using a variety of dynamic mechanical instruments.

1.2This test method is intended to provide a means for determining viscoelastic properties of a wide variety of plastic materials using nonresonant forced-vibration techniques, in accordance with Practice D4065. Plots of the elastic (storage) modulus; loss (viscous) modulus; complex modulus and tan delta as a function of frequency, time, or temperature are indicative of significant transitions in the thermomechanical performance of the polymeric material system.

1.3This test method is valid for a wide range of frequencies, typically from 0.01 to 100 Hz.

1.4Apparent discrepancies may arise in results obtained under differing experimental conditions. These apparent differences from results observed in another study can usually be reconciled, without changing the observed data, by reporting in full (as described in this test method) the conditions under which the data were obtained.

1.5Due to possible instrumentation compliance, the data generated are intended to indicate relative and not necessarily absolute property values.

1.6Test data obtained by this test method are relevant and appropriate for use in engineering design.

1.7The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.

1.8This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1:This test method is technically equivalent to ISO 6721, Part 4.

Committee
D 20
DocumentType
Test Method
Pages
4
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 6382/D6382M : 1999 : R2017 Standard Practice for Dynamic Mechanical Analysis and Thermogravimetry of Roofing and Waterproofing Membrane Material
ASTM D 4065 : 2012 Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures
ASTM D 4065 : 2020 Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures
ASTM D 6382/D6382M : 1999 : R2022 Standard Practice for Dynamic Mechanical Analysis and Thermogravimetry of Roofing and Waterproofing Membrane Material

ASTM D 4092 : 2007 : R2013 Standard Terminology for Plastics: Dynamic Mechanical Properties
ASTM D 4000 : 2013 Standard Classification System for Specifying Plastic Materials
ASTM D 4065 : 2006 Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures
ASTM D 4092 : 1996 Standard Terminology: Plastics: Dynamic Mechanical Properties
ASTM D 4000 : 2003 : REV A Standard Classification System for Specifying Plastic Materials
ASTM D 4000 : 2000 : REV A Standard Classification System for Specifying Plastic Materials
ASTM D 4000 : 2012 Standard Classification System for Specifying Plastic Materials
ASTM D 4000 : 2009 Standard Classification System for Specifying Plastic Materials
ASTM D 4000 : 2011 Standard Classification System for Specifying Plastic Materials
ASTM D 4092 : 2021 Standard Terminology for Plastics: Dynamic Mechanical Properties
ASTM D 4000 : 2004 : EDT 1 Standard Classification System for Specifying Plastic Materials
ASTM D 4092 :2007 Standard Terminology: Plastics: Dynamic Mechanical Properties
ASTM D 4000 : 2023 Standard Classification System for Specifying Plastic Materials
ASTM D 4000 : 2009 : REV B Standard Classification System for Specifying Plastic Materials
ASTM D 4092 : 2001 Standard Terminology: Plastics: Dynamic Mechanical Properties
ASTM D 4000 : 2000 Standard Classification System for Specifying Plastic Materials
ASTM D 4065 : 2012 Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures
ASTM D 4000 : 2010 : REV A Standard Classification System for Specifying Plastic Materials
ASTM D 4000 : 2007 Standard Classification System for Specifying Plastic Materials
ASTM D 4000 : 2009 : REV A Standard Classification System for Specifying Plastic Materials
ASTM D 4000 : 2001 Standard Classification System for Specifying Plastic Materials
ASTM D 4000 : 2008 Standard Classification System for Specifying Plastic Materials
ASTM D 618 : 2013 Standard Practice for Conditioning Plastics for Testing
ASTM D 4000 : 2001 : REV A : EDT 1 Standard Classification System for Specifying Plastic Materials
ASTM D 4000 : 2004 Standard Classification System for Specifying Plastic Materials
ASTM D 4065 : 1995 Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures
ASTM D 4000 : 2010 Standard Classification System for Specifying Plastic Materials
ASTM D 4000 : 2003 Standard Classification System for Specifying Plastic Materials
ASTM D 4000 : 2020 Standard Classification System for Specifying Plastic Materials
ASTM D 618 : 2021 Standard Practice for Conditioning Plastics for Testing
ASTM D 4065 : 2001 Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures

View more information
US$66.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.