ASTM D 5420 : 2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
02-10-2021
English
05-19-2016
This test method covers the determination of the relative ranking of materials according to the energy required to crack or break flat, rigid plastic specimens under various specified conditions of impact of a striker impacted by a falling weight.
1.1This test method covers the determination of the relative ranking of materials according to the energy required to crack or break flat, rigid plastic specimens under various specified conditions of impact of a striker impacted by a falling weight.
1.2The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1:There is no known ISO equivalent to this standard.
| Committee |
D 20
|
| DocumentType |
Test Method
|
| Pages |
8
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM D 7745 : 2011 | Standard Practice for Testing Pultruded Composites |
| ASTM D 6395 : 2011 | Standard Test Method for Flatwise Flexural Impact Resistance of Rigid Plastics (Withdrawn 2019) |
| ASTM E 2136 : 2004 : R2013 | Standard Guide for Specifying and Evaluating Performance of Single Family Attached and Detached Dwellings—Durability (Withdrawn 2022) |
| ASTM D 4000 : 2016 | Standard Classification System for Specifying Plastic Materials |
| ASTM C 1629/C1629M : 2019 | Standard Classification for Abuse-Resistant Nondecorated Interior Gypsum Panel Products and Fiber-Reinforced Cement Panels |
| ASTM D 8161 : 2017 | Standard Test Method for Impact Resistance of Thermoplastic Pavement Marking Materials over a Highway Substrate by Means of a Striker Impacted by a Falling Weight |
| ANSI/CSA NGV 5.1-2016 (R2020) | Residential fueling appliances |
| ASTM D 4101 : 2017 : EDT 1 | Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials |
| ASTM F 790 : 2018 | Standard Guide for Testing Materials for Aerospace Plastic Transparent Enclosures |
| ASTM D 4000 : 2020 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 7745 : 2019 | Standard Practice for Testing Pultruded Composites |
| ASTM D 1600 : 1999 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 4066 : 2000 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| ASTM D 5947 : 1996 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 3763 : 2014 | Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors |
| ASTM D 3763 : 2000 | Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors |
| ASTM D 4226 : 2005 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
| ASTM D 3763 : 2010 | Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors |
| ASTM D 5947 : 2002 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 4066 : 2001 : REV A : R2008 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) (Withdrawn 2012) |
| ASTM D 4226 : 2019 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
| ASTM D 5947 : 2011 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 5947 : 2018 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 2794 : 1992 | Standard Test Method for Resistence of Organic Coatings to the Effects of Rapid Deformation (Impact) |
| ASTM D 4066 : 2001 : REV A | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| ASTM D 3763 : 2018 | Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors |
| ASTM D 1600 : 2007 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1600 : 2013 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 5628 : 2018 | Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimens by Means of a Falling Dart (Tup or Falling Mass) |
| ASTM D 5628 : 2006 | Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimens by Means of a Falling Dart (Tup or Falling Mass) |
| ASTM D 1600 : 2014 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1600 : 2008 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 4066 : 2013 : R2019 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| ASTM D 5947 : 2006 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 4066 : 2001 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| ASTM D 3763 : 2008 | Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors |
| ASTM D 2794 : 1993 : R1999 : EDT 1 | Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact) |
| ASTM D 4066 : 1994 : REV B | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| ASTM D 4066 : 2013 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| ASTM D 2794 : 1993 : R2004 | Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact) |
| ASTM D 3763 : 2010 : EDT 1 | Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors |
| ASTM D 4226 : 2010 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
| ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
| ASTM D 5947 : 2003 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 4226 : 2016 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
| ASTM D 5628 : 1996 | Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimens by Means of a Falling Dart (Tup or Falling Mass) |
| ASTM D 3763 : 2015 | Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors |
| ASTM D 3763 : 2002 | Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors |
| ASTM D 4066 : 2000 : REV A | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| ASTM D 4226 : 2000 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
| ASTM D 3763 : 2006 | Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors |
| ASTM D 2794 : 1993 : R2019 | Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact) |
| ASTM D 5628 : 2007 | Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimens by Means of a Falling Dart (Tup or Falling Mass) |
| ASTM D 2794 : 1993 : R2010 | Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact) |
| ASTM D 4066 : 1996 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| ASTM D 4226 : 2009 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
| ASTM D 4226 : 2011 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
| ASTM D 5628 : 2010 | Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimens by Means of a Falling Dart (Tup or Falling Mass) |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.