• There are no items in your cart

ASTM D 5628 : 2018

Current
Current

The latest, up-to-date edition.

Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimens by Means of a Falling Dart (Tup or Falling Mass)
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

06-14-2018

This test method covers the determination of the threshold value of impact-failure energy required to crack or break flat, rigid plastic specimens under various specified conditions of impact of a free-falling dart (tup), based on testing many specimens.

1.1This test method covers the determination of the threshold value of impact-failure energy required to crack or break flat, rigid plastic specimens under various specified conditions of impact of a free-falling dart (tup), based on testing many specimens.

1.2The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 8.

Note 1:This test method and ISO 6603-1 are technically equivalent only when the test conditions and specimen geometry required for Geometry FE and the Bruceton Staircase method of calculation are used.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 20
DocumentType
Test Method
ISBN
0
Pages
10
PublisherName
American Society for Testing and Materials
Status
Current
Supersedes

ASTM D 5420 : 2016 Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact)
ASTM D 8161 : 2017 Standard Test Method for Impact Resistance of Thermoplastic Pavement Marking Materials over a Highway Substrate by Means of a Striker Impacted by a Falling Weight
ASTM D 4000 : 2016 Standard Classification System for Specifying Plastic Materials

ASTM D 1600 : 1999 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 6779 : 2002 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 883 : 2023 Standard Terminology Relating to Plastics
ASTM D 6779 : 2005 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2020 Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ASTM D 5947 : 1996 Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
ASTM D 6779 : 2007 : REV A Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 3763 : 2014 Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors
ASTM D 4000 : 2013 Standard Classification System for Specifying Plastic Materials
ASTM D 1709 : 2022 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 1709 : 2004 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 2444 : 1999 : R2010 Standard Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
ASTM D 2444 : 2019 Standard Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
ASTM D 3763 : 2000 Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors
ASTM D 4000 : 2003 : REV A Standard Classification System for Specifying Plastic Materials
ASTM D 3763 : 2010 Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors
ASTM D 6779 : 2003 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 4000 : 2000 : REV A Standard Classification System for Specifying Plastic Materials
ASTM D 5947 : 2002 Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
ASTM D 883 : 2024 Standard Terminology Relating to Plastics
ASTM D 4000 : 2012 Standard Classification System for Specifying Plastic Materials
ASTM D 4000 : 2009 Standard Classification System for Specifying Plastic Materials
ASTM D 2444 : 2017 Standard Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
ASTM D 6779 : 2011 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 4000 : 2011 Standard Classification System for Specifying Plastic Materials
ASTM D 883 : 2022 Standard Terminology Relating to Plastics
ASTM D 883 : 2020 : REV B Standard Terminology Relating to Plastics
ASTM D 6779 : 2008 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 5947 : 2011 Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
ASTM D 5947 : 2018 Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
ASTM E 691 : 2020 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 6779 : 2004 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 3763 : 2018 Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors
ASTM D 1600 : 2007 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 4000 : 2004 : EDT 1 Standard Classification System for Specifying Plastic Materials
ASTM D 1600 : 2013 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 6779 : 2012 Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ASTM D 1709 : 2015 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 2444 : 2021 Standard Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
ASTM D 1600 : 2014 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 6779 : 2006 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 4000 : 2023 Standard Classification System for Specifying Plastic Materials
ASTM D 1600 : 2008 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM E 691 : 2019 : EDT 1 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E 691 : 2023 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 4000 : 2009 : REV B Standard Classification System for Specifying Plastic Materials
ASTM D 1709 : 2009 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 4000 : 2000 Standard Classification System for Specifying Plastic Materials
ASTM D 1709 : 1998 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 5947 : 2006 Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
ASTM D 4000 : 2010 : REV A Standard Classification System for Specifying Plastic Materials
ASTM D 3763 : 2008 Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors
ASTM D 1709 : 2001 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 4000 : 2007 Standard Classification System for Specifying Plastic Materials
ASTM D 4000 : 2009 : REV A Standard Classification System for Specifying Plastic Materials
ASTM E 691 : 2022 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 4000 : 2001 Standard Classification System for Specifying Plastic Materials
ASTM E 691 : 2009 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 4000 : 2008 Standard Classification System for Specifying Plastic Materials
ASTM D 3763 : 2010 : EDT 1 Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors
ASTM D 2444 : 1999 Standard Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
ASTM D 1709 : 2016 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 6779 : 2004 : REV A Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2023 Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ASTM D 1600 : 2018 Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
ASTM D 6779 : 2012 : REV A Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ASTM D 618 : 2013 Standard Practice for Conditioning Plastics for Testing
ASTM E 691 : 2021 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 5947 : 2003 Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
ASTM D 1709 : 2008 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 4000 : 2001 : REV A : EDT 1 Standard Classification System for Specifying Plastic Materials
ASTM D 5947 : 2001 : EDT 1 Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
ASTM D 6779 : 2002 : REV A Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 4000 : 2004 Standard Classification System for Specifying Plastic Materials
ASTM D 2444 : 1999 : R2005 Standard Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
ASTM D 3763 : 2015 Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors
ASTM D 3763 : 2002 Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors
ASTM D 4000 : 2010 Standard Classification System for Specifying Plastic Materials
ASTM D 1709 : 2016 : REV A : EDT 1 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 3763 : 2006 Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors
ASTM D 6779 : 2016 Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2007 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 1709 : 2003 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 6779 : 2021 Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2010 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 3763 : 2023 Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors
ASTM D 4000 : 2003 Standard Classification System for Specifying Plastic Materials
ASTM D 1709 : 2015 : REV A Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 4000 : 2020 Standard Classification System for Specifying Plastic Materials
ASTM D 618 : 2021 Standard Practice for Conditioning Plastics for Testing
ASTM D 1709 : 2016 : REV A Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 6779 : 2017 Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2008 : REV A Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2006 : EDT 1 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)

View more information
US$63.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.