• There are no items in your cart

ASTM D 5741 : 1996 : R2017

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Practice for Characterizing Surface Wind Using a Wind Vane and Rotating Anemometer
Available format(s)

Hardcopy , PDF

Superseded date

10-19-2023

Language(s)

English

Published date

03-31-2017

CONTAINED IN VOL. 11.03, 2017 Defines a method for characterizing surface wind speed, wind direction, peak one-minute speeds, peak three-second and peak one-minute speeds, and standard deviations of fluctuation about the means of speed and direction.

1.1This practice covers a method for characterizing surface wind speed, wind direction, peak one-minute speeds, peak three-second and peak one-minute speeds, and standard deviations of fluctuation about the means of speed and direction.

1.2This practice may be used with other kinds of sensors if the response characteristics of the sensors, including their signal conditioners, are equivalent or faster and the measurement uncertainty of the system is equivalent or better than those specified below.

1.3The characterization prescribed in this practice will provide information on wind acceptable for a wide variety of applications.

Note 1:This practice builds on a consensus reached by the attendees at a workshop sponsored by the Office of the Federal Coordinator for Meteorological Services and Supporting Research in Rockville, MD on Oct. 29–30, 1992.

1.4The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 22
DevelopmentNote
Supersedes ASTM D 4480. (12/2001)
DocumentType
Standard Practice
Pages
5
ProductNote
Reconfirmed 2017
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 711 : 2023 Standard Test Method for No-Pick-Up Time of Pavement Markings
ASTM D 711 : 2010 : R2015 Standard Test Method for No-Pick-Up Time of Traffic Paint

ASTM D 5096 : 2023 Standard Test Method for Determining the Performance of a Cup Anemometer or Propeller Anemometer
ASTM D 5096 : 2002 : R2011 Standard Test Method for Determining the Performance of a Cup Anemometer or Propeller Anemometer
ASTM D 5366 : 1996 : R2017 Standard Test Method for Determining the Dynamic Performance of a Wind Vane
ASTM D 1356 : 2015 Standard Terminology Relating to Sampling and Analysis of Atmospheres
ASTM D 5366 : 1996 : R2002 : EDT 1 Standard Test Method for Determining the Dynamic Performance of a Wind Vane
ASTM D 1356 : 2017 Standard Terminology Relating to Sampling and Analysis of Atmospheres
ASTM D 5096 : 1996 Standard Test Method for Determining the Performance of a Cup Anemometer or Propeller Anemometer
ASTM D 1356 : 2015 : REV B Standard Terminology Relating to Sampling and Analysis of Atmospheres
ASTM D 5366 : 1996 : R2011 Standard Test Method for Determining the Dynamic Performance of a Wind Vane
ASTM D 1356 : 2014 : REV A Standard Terminology Relating to Sampling and Analysis of Atmospheres
ASTM D 5366 : 1996 Standard Test Method for Determining the Dynamic Performance of a Wind Vane
ASTM D 5096 : 2002 : R2007 Standard Test Method for Determining the Performance of a Cup Anemometer or Propeller Anemometer
ASTM D 5366 : 1996 : R2007 Standard Test Method for Determining the Dynamic Performance of a Wind Vane
ASTM D 1356 : 2015 : REV A Standard Terminology Relating to Sampling and Analysis of Atmospheres
ASTM D 1356 : 2005 : R2010 Standard Terminology Relating to Sampling and Analysis of Atmospheres
ASTM D 5096 : 2002 : R2017 Standard Test Method for Determining the Performance of a Cup Anemometer or Propeller Anemometer
ASTM D 5366 : 2023 Standard Test Method for Determining the Dynamic Performance of a Wind Vane
ASTM D 1356 : 2020 Standard Terminology Relating to Sampling and Analysis of Atmospheres
ASTM D 1356 : 2000 : REV A Standard Terminology Relating to Sampling and Analysis of Atmospheres
ASTM D 1356 : 2014 : REV B Standard Terminology Relating to Sampling and Analysis of Atmospheres
ASTM D 1356 : 2014 Standard Terminology Relating to Sampling and Analysis of Atmospheres
ASTM D 5096 : 2002 Standard Test Method for Determining the Performance of a Cup Anemometer or Propeller Anemometer
ASTM D 1356 : 2005 Standard Terminology Relating to Sampling and Analysis of Atmospheres

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.