• There are no items in your cart

ASTM D 7589 : 2016 : REDLINE

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VID Spark Ignition Engine
Available format(s)

PDF

Superseded date

04-08-2016

Language(s)

English

Published date

04-08-2016

CONTAINED IN VOL. 05.04, 2018 Defines an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight 3856 kg or less.

1.1This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight 3856 kg or less. The tests are conducted using a specified spark-ignition engine with a displacement of 3.6 L (General Motors)4 on a dynamometer test stand. It applies to multi viscosity grade oils used in these applications.

1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.2.1Exceptions—Where there is no direct equivalent such as the units for screw threads, National Pipe threads/diameters, tubing size, and single source supply equipment specifications. Additionally, Brake Fuel Consumption (BSFC) is measured in kilograms per kilowatthour.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.4This test method is arranged as follows:

Subject

Section

Introduction

Scope

1

Referenced Documents

2

Terminology

3

Summary of Test Method

4

Significance and Use

5

Apparatus

6

General

6.1

Test Engine Configuration

6.2

Laboratory Ambient Conditions

6.3

Engine Speed and Torque Control

6.4

Dynamometer

6.4.1

Dynamometer Torque

6.4.2

Engine Cooling System

6.5

External Oil System

6.6

Fuel System

6.7

Fuel Flow Measurement

6.7.2

Fuel Temperature and Pressure Control to the Fuel
 Flowmeter

6.7.3

Fuel Temperature and Pressure Control to Engine Fuel Rail

6.7.4

Fuel Supply Pumps

6.7.5

Fuel Filtering

6.7.6

Engine Intake Air Supply

6.8

Intake Air Humidity

6.8.1

Intake Air Filtration

6.8.2

Intake Air Pressure Relief

6.8.3

Temperature Measurement

6.9

Thermocouple Location

6.9.5

AFR Determination

6.10

Exhaust and Exhaust Back Pressure Systems

6.11

Exhaust Manifolds

6.11.1

Laboratory Exhaust System

6.11.2

Exhaust Back Pressure

6.11.3

Pressure Measurement and Pressure Sensor Locations

6.12

Engine Oil

6.12.2

Fuel to Fuel Flowmeter

6.12.3

Fuel to Engine Fuel Rail

6.12.4

Exhaust Back Pressure

6.12.5

Intake Air

6.12.6

Intake Manifold Vacuum/Absolute Pressure

6.12.7

Coolant Flow Differential Pressure

6.12.8

Crankcase Pressure

6.12.9

Engine Hardware and Related Apparatus

6.13

Test Engine Configuration

6.13.1

ECU (Power Control Module)

6.13.2

Thermostat Block-Off Adapter Plate

6.13.3

Wiring Harness

6.13.4

Oil Pan

6.13.5

Engine Water Pump Adapter Plate

6.13.6

Thermostat Block-Off Plate

6.13.7

Oil Filter Adapter Plate

6.13.8

Modified Throttle Body Assembly

6.13.9

Fuel Rail

6.13.10

Miscellaneous Apparatus Related to Engine Operation

6.14

Reagents and Materials

7

Engine Oil

7.1

Test Fuel

7.2

Engine Coolant

7.3

Cleaning Materials

7.4

Preparation of Apparatus

8

Test Stand Preparation

8.2

Engine Preparation

9

Cleaning of Engine Parts

9.3

Engine Assembly Procedure

9.4

General Assembly Instructions

9.4.1

Bolt Torque Specifications

9.4.2

Sealing Compounds

9.4.3

Harmonic Balancer

9.4.5

Thermostat

9.4.6

Coolant Inlet

9.4.7

Oil Filter Adapter

9.4.8

Dipstick Tube

9.4.9

Sensors, Switches, Valves, and Positioners

9.4.10

Ignition System

9.4.11

Fuel Injection System

9.4.12

Intake Air System

9.4.13

Engine Management System

9.4.14

Accessory Drive Units

9.4.15

Exhaust Manifolds

9.4.16

Engine Flywheel and Guards

9.4.17

Lifting of Assembled Engines

9.4.18

Engine Mounts

9.4.19

Non-Phased Camshaft Gears

9.4.20

Internal Coolant Orifice

9.4.21

Calibration

10

Stand/Engine Calibration

10.1

Procedure

10.1.1

Reporting of Reference Results

10.1.2

Instrument Calibration

10.2

Engine Torque Measurement System

10.2.3

Fuel Flow Measurement System

10.2.4

Coolant Flow Measurement System

10.2.5

Thermocouple and Temperature Measurement System

10.2.6

Humidity Measurement System

10.2.7

Other Instrumentation

10.2.8

Test Procedure

11

External Oil System

11.1

Flush Effectiveness Demonstration

11.2

Preparation for Oil Charge

11.3

Initial Engine Start-Up

11.4

New Engine Break-In

11.5

Oil Charge for Break-In

11.5.2

Break-In Operating Conditions

11.5.3

Standard Requirements for Break-In

11.5.4

Routine Test Operation

11.6

Start-Up and Shutdown Procedures

11.6.1

Flying Flush Oil Exchange Procedures

11.6.2

Test Operating Stages

11.6.3

Stabilization to Stage Conditions

11.6.4

Stabilized BSFC Measurement Cycle

11.6.5

BLB1 Oil Flush Procedure for BL Oil Before Test Run 1

11.6.6

BSFC Measurement of BLB1 Oil Before Test Oil

11.6.7

BLB2 Oil Flush Procedure for BL Oil Before Test Oil Run 2

11.6.8

BSFC Measurement of BLB2 Oil Before Test Oil

11.6.9

Percent Delta Calculation for BLB1 vs. BLB2

11.6.10

Test Oil Flush Procedure

11.6.11

Test Oil Aging, Phase I

11.6.12

BSFC Measurement of Aged (Phase I) Test Oil

11.6.13

Test Oil Aging, Phase II

11.6.14

BSFC Measurement of Aged (Phase II) Test Oil

11.6.15

Oil Consumption and Sampling

11.6.16

Flush Procedure for BL Oil (BLA) After Test Oil

11.6.17

General Test Data Logging Forms

11.6.18

Diagnostic Review Procedures

11.6.19

Determination of Test Results

12

Report

13

Precision and Bias

14

Keywords

15

Annexes

ASTM Test Monitoring Center: Organization

Annex A1

ASTM Test Monitoring Center: Calibration Procedures

Annex A2

ASTM Test Monitoring Center: Maintenance Activities

Annex A3

ASTM Test Monitoring Center: Related Information

Annex A4

Detailed Specifications and Drawings of Apparatus

Annex A5

Oil Heater Cerrobase Refill Procedure

Annex A6

Engine Part Number Listing

Annex A7

Safety Precautions

Annex A8

Report Format

Annex A9

Statistical Equations for Mean and Standard Deviations

Annex A10

Oil Sump Full Level Determination Consumption
 Measurement Calibration Procedure

Annex A11

Fuel Injector Evaluation

Annex A12

Pre-test Maintenance Checklist

Annex A13

Blow-by Ventilation System Requirements

Annex A14

Calculation of Test Results

Annex A15

Calculation of Unweighted Baseline Shift

Annex A16

Non–Phased Cam Gear and Position Actuator Installation Procedure

Annex A17

Appendix

Procurement of Test Materials

Appendix X1

Committee
D 02
DocumentType
Redline
Pages
65
PublisherName
American Society for Testing and Materials
Status
Superseded

SAE J 183 : 2017 ENGINE OIL PERFORMANCE AND ENGINE SERVICE CLASSIFICATION (OTHER THAN 'ENERGY CONSERVING')
SAE J 1423 : 2015 CLASSIFICATION OF ENERGY CONSERVING ENGINE OIL AND RESOURCE CONSERVING ENGINE OIL FOR PASSENGER CARS, VANS, SPORT UTILITY VEHICLES, AND LIGHT-DUTY TRUCKS
SAE J 304 : 2016 ENGINE OIL TESTS

API 1509 : 2002 ENGINE OIL LICENSING AND CERTIFICATION SYSTEM
ASTM D 86 : 2017-06 TEST METHOD FOR DISTILLATION OF PETROLEUM PRODUCTS AND LIQUID FUELS AT ATMOSPHERIC PRESSURE
IEEE/ASTM SI_10-2010 American National Standard for Metric Practice
ANSI MC96.1 : 1982 TEMPERATURE MEASUREMENT THERMOCOUPLES
SAE J 304 : 2016 ENGINE OIL TESTS
ASTM D 3237 : 2017 : REDLINE Standard Test Method for Lead in Gasoline by Atomic Absorption Spectroscopy
ASTM D 6837 : 2013 : REDLINE Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VIB Spark Ignition Engine<rangeref></rangeref >
SAE J 1423 : 2015 CLASSIFICATION OF ENERGY CONSERVING ENGINE OIL AND RESOURCE CONSERVING ENGINE OIL FOR PASSENGER CARS, VANS, SPORT UTILITY VEHICLES, AND LIGHT-DUTY TRUCKS
ASTM D 240 : 2017 : REDLINE Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter

View more information
US$125.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.