• There are no items in your cart

ASTM D 7750 : 2012 : R2017

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Cure Behavior of Thermosetting Resins by Dynamic Mechanical Procedures using an Encapsulated Specimen Rheometer
Available format(s)

Hardcopy , PDF

Superseded date

06-09-2023

Language(s)

English

Published date

09-13-2017

CONTAINED IN VOL. 15.03, 2017 Defines the use of dynamic mechanical instrumentation for determination and reporting of the thermal advancement of cure behavior of thermosetting resin on an inert filler or fiber in a laboratory.

1.1This method covers the use of dynamic mechanical instrumentation for determination and reporting of the thermal advancement of cure behavior of thermosetting resin on an inert filler or fiber in a laboratory. It may also be used for determining the cure properties of filled resins and resins without reinforcements. These encapsulated specimens are deformed in torsional shear using dynamic mechanical methods.

1.2This method is intended to provide means for determining the cure behavior of thermosetting resins on fibers over a range of temperatures from room temperature to 250°C by forced-constant amplitude techniques (in accordance with Practice D4065). Plots of complex modulus, complex viscosity, and damping ratio or tan delta as a function of time or temperature, or both, quantify the thermal advancement or cure characteristics of a resin or a resin on fiber.

1.3Test data obtained by this method is relevant and appropriate for optimizing cure cycles.

1.4The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.4.1Exception—The fahrenheit temperature measurement in 10.1 is provided for information only and is not considered standard.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 30
DocumentType
Test Method
Pages
8
ProductNote
Reconfirmed 2017
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 3532/D3532M : 2019 Standard Test Method for Gel Time of Carbon Fiber-Epoxy Prepreg
ASTM D 4762 : 2018 Standard Guide for Testing Polymer Matrix Composite Materials

ASTM D 4092 : 2007 : R2013 Standard Terminology for Plastics: Dynamic Mechanical Properties
ASTM E 380 : 1993 Standard Practice for Use of the Internation System of Units (SI) (the Modernized Metric System) (Withdrawn 1997)
ASTM D 4000 : 2013 Standard Classification System for Specifying Plastic Materials
ASTM D 4065 : 2006 Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures
ASTM D 4092 : 1996 Standard Terminology: Plastics: Dynamic Mechanical Properties
ASTM D 3878 : 2002 : REV A Standard Terminology for Composite Materials
ASTM D 6507 : 2019 Standard Practice for Fiber Reinforcement Orientation Codes for Composite Materials
ASTM D 4000 : 2003 : REV A Standard Classification System for Specifying Plastic Materials
ASTM D 4000 : 2000 : REV A Standard Classification System for Specifying Plastic Materials
ASTM D 4000 : 2012 Standard Classification System for Specifying Plastic Materials
ASTM D 4000 : 2009 Standard Classification System for Specifying Plastic Materials
ASTM D 3878 : 2015 Standard Terminology for Composite Materials
ASTM D 3878 : 2019 Standard Terminology for Composite Materials
ASTM D 3878 : 2000 Standard Terminology Composite Materials
ASTM D 7028 : 2007 Standard Test Method for Glass Transition Temperature (DMA Tg) of Polymer Matrix Composites by Dynamic Mechanical Analysis (DMA)
ASTM D 4473 : 2003 Standard Test Method for Plastics: Dynamic Mechanical Properties: Cure Behavior
ASTM D 4000 : 2011 Standard Classification System for Specifying Plastic Materials
ASTM D 4092 : 2021 Standard Terminology for Plastics: Dynamic Mechanical Properties
ASTM D 4000 : 2004 : EDT 1 Standard Classification System for Specifying Plastic Materials
ASTM D 6507 : 2016 : REDLINE Standard Practice for Fiber Reinforcement Orientation Codes for Composite Materials
ASTM D 4092 :2007 Standard Terminology: Plastics: Dynamic Mechanical Properties
ASTM D 4000 : 2023 Standard Classification System for Specifying Plastic Materials
ASTM D 4473 : 2008 : R2016 Standard Test Method for Plastics: Dynamic Mechanical Properties: Cure Behavior
ASTM D 3878 : 2003 : REV A Standard Terminology for Composite Materials
ASTM D 3878 : 2016 Standard Terminology for Composite Materials
ASTM D 4473 : 2008 : R2021 Standard Test Method for Plastics: Dynamic Mechanical Properties: Cure Behavior
ASTM D 4000 : 2009 : REV B Standard Classification System for Specifying Plastic Materials
ASTM D 4092 : 2001 Standard Terminology: Plastics: Dynamic Mechanical Properties
ASTM D 3878 : 2019 : REV A Standard Terminology for Composite Materials
ASTM D 3878 : 2020 : REV A Standard Terminology for Composite Materials
ASTM D 3878 : 1998 Standard Terminology Composite Materials
ASTM D 4000 : 2000 Standard Classification System for Specifying Plastic Materials
ASTM D 4065 : 2012 Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures
ASTM D 4000 : 2010 : REV A Standard Classification System for Specifying Plastic Materials
ASTM D 3878 : 2018 Standard Terminology for Composite Materials
ASTM D 4000 : 2007 Standard Classification System for Specifying Plastic Materials
ASTM D 6507 : 2011 Standard Practice for Fiber Reinforcement Orientation Codes for Composite Materials
ASTM D 4000 : 2009 : REV A Standard Classification System for Specifying Plastic Materials
ASTM D 4000 : 2001 Standard Classification System for Specifying Plastic Materials
ASTM D 3878 : 2002 Standard Terminology for Composite Materials
ASTM D 4000 : 2008 Standard Classification System for Specifying Plastic Materials
ASTM D 6507 : 2016 Standard Practice for Fiber Reinforcement Orientation Codes for Composite Materials
ASTM D 4473 : 1995 : REV A Standard Test Method for Plastics: Dynamic Mechanical Properties: Cure Behavior
ASTM D 3878 : 2004 Standard Terminology for Composite Materials
ASTM D 4000 : 2001 : REV A : EDT 1 Standard Classification System for Specifying Plastic Materials
ASTM D 3878 : 2007 : R2013 Standard Terminology for Composite Materials
ASTM D 4000 : 2004 Standard Classification System for Specifying Plastic Materials
ASTM D 3878 : 2020 : REDLINE Standard Terminology for Composite Materials
ASTM D 3878 : 2020 Standard Terminology for Composite Materials
ASTM D 4065 : 2012 : REDLINE Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures
ASTM D 3878 : 2003 Standard Terminology for Composite Materials
ASTM D 4065 : 1995 Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures
ASTM D 3878 : 2007 Standard Terminology for Composite Materials
ASTM D 6507 : 2000 : R2005 Standard Practice for Fiber Reinforcement Orientation Codes for Composite Materials
ASTM D 4000 : 2010 Standard Classification System for Specifying Plastic Materials
ASTM D 6507 : 2000 Standard Practice for Fiber Reinforcement Orientation Codes for Composite Materials
ASTM D 7028 : 2007 : EDT 1 Standard Test Method for Glass Transition Temperature (DMA Tg) of Polymer Matrix Composites by Dynamic Mechanical Analysis (DMA)
ASTM D 4473 : 2001 Standard Test Method for Plastics: Dynamic Mechanical Properties: Cure Behavior
ASTM D 4473 : 2008 Standard Test Method for Plastics: Dynamic Mechanical Properties: Cure Behavior
ASTM D 3878 : 2004 : REV A Standard Terminology for Composite Materials
ASTM D 4000 : 2003 Standard Classification System for Specifying Plastic Materials
ASTM D 7028 : 2007 : R2015 Standard Test Method for Glass Transition Temperature (DMA Tg) of Polymer Matrix Composites by Dynamic Mechanical Analysis (DMA)
ASTM D 4000 : 2020 Standard Classification System for Specifying Plastic Materials
ASTM D 3878 : 2001 Standard Terminology Composite Materials
ASTM D 4000 : 2016 : REDLINE Standard Classification System for Specifying Plastic Materials
ASTM D 4065 : 2001 Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.