• There are no items in your cart

ASTM D 8065/D8065M : 2016

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Classification System and Basis for Specification for Specifying Plastic Films
Available format(s)

Hardcopy , PDF

Superseded date

11-09-2023

Language(s)

English

Published date

09-09-2016

CONTAINED IN VOL. 08.03, 2016 Specifies a classification system for tabulating the properties of unfilled, single-layer plastic films.

1.1This standard provides a classification system for tabulating the properties of unfilled, single-layer plastic films.

Note 1:The classification system serves many of the needs of industries using plastic films. The standard is subject to revision as the need requires; therefore, the latest revision should always be used.

Note 2:Film is defined in Terminology D883 as an optional term for sheeting having a nominal thickness no greater than 0.25 mm [0.010 in.].

1.2The classification system and subsequent line call-out (specification) is intended to be a means of identifying plastic films used for applications including industrial, packaging, construction, and agriculture. It is not intended for the selection of materials to be used in films. This selection should be made by those having expertise in the plastics field after careful consideration of the end-use requirements, the environment to which the films will be exposed, the fabrication process to be employed, the inherent properties of the material not covered in this document, and the economic factors.

1.3This classification system is based on the premise that plastic films can be arranged into broad generic families based on materials with similar composition using basic film properties. A system is thus established which, together with values describing additional requirements, permits as complete a description as desired of the selected film.

1.4In all cases where the provisions of this classification system would conflict with the referenced ASTM specification for a particular film product, the latter shall take precedence.

Note 3:It is strongly recommended that this classification system be used for all new applications and specifications and that the specification of films using existing standards be expeditiously withdrawn or converted to this classification system.

1.5This classification system applies to commercial products and, as such, there is no control over the manufacturing parameters employed in producing the film. It shall be the responsibility of those developing the specification documents utilizing this classification system to identify the critical parameters and values to be used for the cell classifications and suffix requirements.

1.6Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 4:There is no known ISO equivalent to this standard.

Committee
D 20
DocumentType
Standard
Pages
5
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

ASTM D 8195 : 2018 Standard Classification System and Basis for Specification for Polyethylene Terephthalate Film and Sheeting

ASTM D 2732 : 2008 Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film and Sheeting
ASTM E 96/E96M : 2016 : REDLINE Standard Test Methods for Water Vapor Transmission of Materials
ASTM D 1746 : 1997 Standard Test Method for Transparency of Plastic Sheeting
ASTM D 1203 : 1994 : R1999 : EDT 1 Standard Test Methods for Volatile Loss From Plastics Using Activated Carbon Methods
ASTM D 1004 : 2008 Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting
ASTM D 6988 : 2008 Standard Guide for Determination of Thickness of Plastic Film Test Specimens
ASTM D 1894 : 2014 : REDLINE Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting
ASTM D 1894 : 2011 Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting
ASTM D 1922 : 2008 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 7192 : 2005 Standard Test Method for High Speed Puncture Properties of Plastic Films Using Load and Displacement Sensors
ASTM D 3420 : 2014 : REDLINE Standard Test Method for Pendulum Impact Resistance of Plastic Film
ASTM D 2578 : 2009 Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films
ASTM D 3420 : 2008 Standard Test Method for Pendulum Impact Resistance of Plastic Film
ASTM D 2582 : 2008 Standard Test Method for Puncture-Propagation Tear Resistance of Plastic Film and Thin Sheeting
ASTM D 1204 : 2014 : REDLINE Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature
ASTM D 1204 : 2007 Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature
ASTM D 2275 : 2001 : R2008 : EDT 1 Standard Test Method for Voltage Endurance of Solid Electrical Insulating Materials Subjected to Partial Discharges (Corona) on the Surface
ASTM D 150 : 2022 Standard Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation
ASTM D 1709 : 2022 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 3801 : 2006 Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position
ASTM D 2732 : 2014 : R2020 Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film<brk/> and Sheeting
ASTM E 29 : 2013 : R2019 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
ASTM D 7192 : 2019 Standard Test Method for High Speed Puncture Properties of Plastic Films Using Load and Displacement Sensors
ASTM D 3354 : 2008 Standard Test Method for Blocking Load of Plastic Film by the Parallel Plate Method
ASTM D 3892 : 2015 : R2020 Standard Practice for Packaging/Packing of Plastics
ASTM D 1434 : 1982 : R2003 Standard Test Method for Determining Gas Permeability Characteristics of Plastic Film and Sheeting
ASTM E 96/E96M : 2022 : REV A : EDT 1 Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials
ASTM D 2305 : 2010 Standard Test Methods for Polymeric Films Used for Electrical Insulation
ASTM D 1709 : 2004 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 4272/D4272M : 2015 Standard Test Method for Total Energy Impact of Plastic Films by Dart Drop
ASTM D 1004 : 1994 : REV A Standard Test Method for Initial Tear Resistance of Plastic Film and Sheeting
ASTM E 96/E96M : 2022 : REV A Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials
ASTM D 2176 : 2016 : R2021 Standard Test Method for Folding Endurance of Paper and Plastics Film by the M.I.T. Tester
ASTM D 3420 : 2014 Standard Test Method for Pendulum Impact Resistance of Plastic Film
ASTM D 1004 : 2009 Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting
ASTM D 1003 : 2007 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
ASTM D 6988 : 2021 Standard Guide for Determination of Thickness of Plastic Film Test Specimens
ASTM D 1790 : 2002 Standard Test Method for Brittleness Temperature of Plastic Sheeting by Impact
ASTM D 1790 : 2014 Standard Test Method for Brittleness Temperature of Plastic Sheeting by Impact
ASTM D 1204 : 2014 Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature
ASTM D 2923 : 2008 Standard Test Method for Rigidity of Polyolefin Film and Sheeting
ASTM D 1746 : 2023 Standard Test Method for Transparency of Plastic Sheeting
ASTM D 3420 : 2008 : REV A Standard Test Method for Pendulum Impact Resistance of Plastic Film
ASTM D 2923 : 2013 Standard Test Method for Rigidity of Polyolefin Film and Sheeting (Withdrawn 2015)
ASTM D 1003 : 2013 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
ASTM E 96/E96M : 2021 Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials
ASTM D 1203 : 2022 Standard Test Methods for Volatile Loss from Plastics Using Activated Carbon Methods
ASTM D 1004 : 2013 Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting
ASTM D 2838 : 2008 Standard Test Method for Shrink Tension and Orientation Release Stress of Plastic Film and Thin Sheeting
ASTM D 7192 : 2010 Standard Test Method for High Speed Puncture Properties of Plastic Films Using Load and Displacement Sensors
ASTM D 1922 : 2015 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM E 29 : 2002 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
ASTM D 2457 : 2008 Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics
ASTM D 2582 : 2003 Standard Test Method for Puncture-Propagation Tear Resistance of Plastic Film and Thin Sheeting
ASTM D 2578 : 2008 Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films
ASTM D 3892 : 1993 : R2003 Standard Practice for Packaging/Packing of Plastics
ASTM D 1922 : 2023 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 3892 : 2015 Standard Practice for Packaging/Packing of Plastics
ASTM D 2305 : 2018 Standard Test Methods for Polymeric Films Used for Electrical Insulation
ASTM D 1894 : 2000 Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting
ASTM D 1922 : 2006 : REV A Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 1004 : 1994 : REV A : R2003 Standard Test Method for Initial Tear Resistance of Plastic Film and Sheeting
ASTM D 257 : 2014 Standard Test Methods for DC Resistance or Conductance of Insulating Materials
ASTM D 3985 : 2005 Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor
ASTM D 5946 : 2004 Standard Test Method for Corona-Treated Polymer Films Using Water Contact Angle Measurements
ASTM D 3801 : 2000 Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position
ASTM D 883 : 2022 Standard Terminology Relating to Plastics
ASTM D 1790 : 1999 Standard Test Method for Brittleness Temperature of Plastic Sheeting by Impact
ASTM D 1894 : 2001 Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting
ASTM D 3420 : 2021 Standard Test Method for Pendulum Impact Resistance of Plastic Film
ASTM D 2578 : 1999 : REV A Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films
ASTM D 6988 : 2003 Standard Guide for Determination of Thickness of Plastic Film Test Specimens
ASTM E 96/E96M : 2022 Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials
ASTM D 3801 : 2010 Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position
ASTM D 5946 : 2009 Standard Test Method for Corona-Treated Polymer Films Using Water Contact Angle Measurements
ASTM D 883 : 2020 : REV B Standard Terminology Relating to Plastics
ASTM D 7209 : 2006 Standard Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products (Withdrawn 2015)
ASTM D 1938 : 2014 Standard Test Method for Tear-Propagation Resistance (Trouser Tear) of Plastic Film and Thin Sheeting by a Single-Tear Method
ASTM D 3354 : 2015 Standard Test Method for Blocking Load of Plastic Film by the Parallel Plate Method
ASTM D 3892 : 1993 : R1998 Standard Practice for Packaging/Packing of Plastics
ASTM D 2578 : 2017 Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films
ASTM D 1004 : 2013 : REDLINE Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting
ASTM D 1204 : 2008 Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature
ASTM D 3985 : 2005 : R2010 : EDT 1 Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor
ASTM D 3985 : 2002 : EDT 1 Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor
ASTM D 3354 : 1996 Standard Test Method for Blocking Load of Plastic Film by the Parallel Plate Method
ASTM D 1203 : 2016 : REDLINE Standard Test Methods for Volatile Loss From Plastics Using Activated Carbon Methods
ASTM D 3801 : 2019 Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position
ASTM D 4272/D4272M : 2023 Standard Test Method for Total Energy Impact of Plastic Films by Dart Drop
ASTM D 1746 : 2003 Standard Test Method for Transparency of Plastic Sheeting
ASTM D 2582 : 2009 Standard Test Method for Puncture-Propagation Tear Resistance of Plastic Film and Thin Sheeting
ASTM D 1709 : 2015 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 2732 : 1996 Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film and Sheeting
ASTM D 1790 : 2014 : REDLINE Standard Test Method for Brittleness Temperature of Plastic Sheeting by Impact
ASTM D 1239 : 2014 : REDLINE Standard Test Method for Resistance of Plastic Films to Extraction by Chemicals
ASTM D 7192 : 2008 Standard Test Method for High Speed Puncture Properties of Plastic Films Using Load and Displacement Sensors
ASTM D 774/D774M : 1997 Standard Test Method for Bursting Strength of Paper
ASTM D 1004 : 2003 Standard Test Method for Initial Tear Resistance of Plastic Film and Sheeting
ASTM D 2732 : 2003 Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film and Sheeting
ASTM D 7192 : 2018 Standard Test Method for High Speed Puncture Properties of Plastic Films Using Load and Displacement Sensors
ASTM D 1003 : 2007 : EDT 1 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
ASTM D 2582 : 2007 Standard Test Method for Puncture-Propagation Tear Resistance of Plastic Film and Thin Sheeting
ASTM D 2582 : 2016 Standard Test Method for Puncture-Propagation Tear Resistance of Plastic Film and Thin Sheeting
ASTM D 5946 : 1999 Standard Test Method for Corona-Treated Polymer Films Using Water Contact Angle Measurements
ASTM D 1204 : 2014 : R2020 Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature
ASTM D 1004 : 2007 Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting
ASTM D 1203 : 2016 Standard Test Methods for Volatile Loss From Plastics Using Activated Carbon Methods
ASTM D 2176 : 2016 Standard Test Method for Folding Endurance of Paper and Plastics Film by the M.I.T. Tester
ASTM D 1894 : 2014 Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting (Withdrawn 2023)
ASTM D 1922 : 2003 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 3801 : 2019 : REV A Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position
ASTM D 2923 : 2006 Standard Test Method for Rigidity of Polyolefin Film and Sheeting
ASTM D 1709 : 2009 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 1709 : 1998 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 2275 : 2014 Standard Test Method for Voltage Endurance of Solid Electrical Insulating Materials Subjected to Partial Discharges (Corona) on the Surface
ASTM D 2582 : 2000 Standard Test Method for Puncture-Propagation Tear Resistance of Plastic Film and Thin Sheeting
ASTM D 2176 : 1997 : REV A Standard Test Method for Folding Endurance of Paper by the M.I.T. Tester
ASTM D 1203 : 2021 Standard Test Methods for Volatile Loss from Plastics Using Activated Carbon Methods
ASTM D 2457 : 2013 Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics
ASTM D 2457 : 2013 : REDLINE Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics
ASTM D 1203 : 2010 Standard Test Methods for Volatile Loss From Plastics Using Activated Carbon Methods
ASTM D 2176 : 1997 : REV A : R2002 Standard Test Method for Folding Endurance of Paper by the M.I.T. Tester
ASTM D 1709 : 2001 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 3354 : 2011 Standard Test Method for Blocking Load of Plastic Film by the Parallel Plate Method
ASTM D 1894 : 2011 : EDT 1 Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting
ASTM D 6988 : 2007 Standard Guide for Determination of Thickness of Plastic Film Test Specimens
ASTM D 2838 : 1995 Standard Test Method for Shrink Tension and Orientation Release Stress of Plastic Film and Thin Sheeting
ASTM D 5946 : 2001 Standard Test Method for Corona-Treated Polymer Films Using Water Contact Angle Measurements
ASTM D 2923 : 1995 Standard Test Method for Rigidity of Polyolefin Film and Sheeting
ASTM E 96/E96M : 2016 Standard Test Methods for Water Vapor Transmission of Materials
ASTM D 2305 : 1999 Standard Test Methods for Polymeric Films Used for Electrical Insulation
ASTM D 1003 : 2011 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
ASTM D 2923 : 2001 Standard Test Method for Rigidity of Polyolefin Film and Sheeting
ASTM D 2305 : 2002 Standard Test Methods for Polymeric Films Used for Electrical Insulation
ASTM D 1938 : 2002 Standard Test Method for Tear-Propagation Resistance (Trouser Tear) of Plastic Film and Thin Sheeting by a Single-Tear Method
ASTM D 1938 : 1994 Standard Test Method for Tear-Propagation Resistance (Trouser Tear) of Plastic Film and Thin Sheeting by a Single-Tear Method
ASTM D 1709 : 2016 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 1746 : 2009 Standard Test Method for Transparency of Plastic Sheeting
ASTM D 3354 : 2015 : REDLINE Standard Test Method for Blocking Load of Plastic Film by the Parallel Plate Method
ASTM D 1003 : 2013 : REDLINE Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
ASTM D 1239 : 2022 Standard Test Method for Resistance of Plastic Films to Extraction by Chemicals
ASTM D 2732 : 2014 : REDLINE Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film<brk/> and Sheeting
ASTM D 1922 : 2015 : R2020 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 4272/D4272M : 2015 : REDLINE Standard Test Method for Total Energy Impact of Plastic Films by Dart Drop
ASTM D 2578 : 2004 Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films
ASTM D 1003 : 2021 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
ASTM D 2457 : 1997 Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics
ASTM D 2176 : 1997 : REV A : R2007 Standard Test Method for Folding Endurance of Paper by the M.I.T. Tester (Withdrawn 2010)
ASTM D 1434 : 1982 : R2015 : EDT 1 Standard Test Method for Determining Gas Permeability Characteristics of Plastic Film and Sheeting
ASTM D 1239 : 2022 : REV A Standard Test Method for Resistance of Plastic Films to Extraction by Chemicals
ASTM D 1709 : 2008 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 1922 : 2003 : REV A Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 2582 : 2021 Standard Test Method for Puncture-Propagation Tear Resistance of Plastic Film and Thin Sheeting
ASTM D 3801 : 1996 : EDT 1 Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position
ASTM D 5946 : 2017 : REDLINE Standard Test Method for Corona-Treated Polymer Films Using Water Contact Angle Measurements
ASTM D 3985 : 1995 Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor
ASTM D 1204 : 1994 : EDT 1 Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature
ASTM D 1434 : 1982 : R2009 : EDT 1 Standard Test Method for Determining Gas Permeability Characteristics of Plastic Film and Sheeting
ASTM D 2275 : 2022 Standard Test Method for Voltage Endurance of Solid Electrical Insulating Materials Subjected to Partial Discharges (Corona) on the Surface
ASTM D 6988 : 2013 Standard Guide for Determination of Thickness of Plastic Film Test Specimens
ASTM D 1746 : 2015 Standard Test Method for Transparency of Plastic Sheeting
ASTM D 257 : 2014 : REDLINE Standard Test Methods for DC Resistance or Conductance of Insulating Materials
ASTM D 1003 : 2000 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
ASTM D 1922 : 2015 : REDLINE Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 5946 : 2017 Standard Test Method for Corona-Treated Polymer Films Using Water Contact Angle Measurements
ASTM D 2275 : 2001 Standard Test Method for Voltage Endurance of Solid Electrical Insulating Materials Subjected to Partial Discharges (Corona) on the Surface
ASTM D 7192 : 2019 : REDLINE Standard Test Method for High Speed Puncture Properties of Plastic Films Using Load and Displacement Sensors
ASTM D 2732 : 2014 Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film<brk/> and Sheeting
ASTM D 1790 : 2008 Standard Test Method for Brittleness Temperature of Plastic Sheeting by Impact
ASTM D 1790 : 2021 Standard Test Method for Brittleness Temperature of Plastic Sheeting by Impact
ASTM D 1203 : 1994 : R2003 Standard Test Methods for Volatile Loss From Plastics Using Activated Carbon Methods
ASTM D 1922 : 2005 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 3892 : 1993 : R2009 Standard Practice for Packaging/Packing of Plastics
ASTM D 3420 : 1995 Standard Test Method for Pendulum Impact Resistance of Plastic Film
ASTM D 1239 : 2007 Standard Test Method for Resistance of Plastic Films to Extraction by Chemicals
ASTM D 3801 : 2010-08 TEST METHOD FOR MEASURING THE COMPARATIVE BURNING CHARACTERISTICS OF SOLID PLASTICS IN A VERTICAL POSITION
ASTM D 2578 : 2023 Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films
ASTM D 1709 : 2016 : REV A : EDT 1 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 3354 : 2021 Standard Test Method for Blocking Load of Plastic Film by the Parallel Plate Method
ASTM D 1938 : 2008 Standard Test Method for Tear-Propagation Resistance (Trouser Tear) of Plastic Film and Thin Sheeting by a Single-Tear Method
ASTM D 3801 : 2020 Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position
ASTM D 1894 : 2008 Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting
ASTM D 2838 : 2009 : EDT 1 Standard Test Method for Shrink Tension and Orientation Release Stress of Plastic Film and Thin Sheeting (Withdrawn 2018)
ASTM D 1938 : 2006 Standard Test Method for Tear-Propagation Resistance (Trouser Tear) of Plastic Film and Thin Sheeting by a Single-Tear Method
ASTM D 2838 : 2007 Standard Test Method for Shrink Tension and Orientation Release Stress of Plastic Film and Thin Sheeting
ASTM D 6988 : 2013 : REDLINE Standard Guide for Determination of Thickness of Plastic Film Test Specimens
ASTM D 1709 : 2003 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 2457 : 2003 Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics
ASTM D 1003 : 2011 : EDT 1 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
ASTM D 1922 : 2000 : REV A Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 1239 : 2014 Standard Test Method for Resistance of Plastic Films to Extraction by Chemicals
ASTM D 1434 : 2023 Standard Test Method for Determining Gas Permeability Characteristics of Plastic Film and Sheeting
ASTM D 150 : 2018 Standard Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation
ASTM D 1239 : 1998 Standard Test Method for Resistance of Plastic Films to Extraction by Chemicals
ASTM D 1746 : 2015 : REDLINE Standard Test Method for Transparency of Plastic Sheeting
ASTM D 1204 : 2002 Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature
ASTM D 3354 : 2004 Standard Test Method for Blocking Load of Plastic Film by the Parallel Plate Method
ASTM D 1203 : 2020 Standard Test Methods for Volatile Loss From Plastics Using Activated Carbon Methods
ASTM D 2582 : 2016 : REDLINE Standard Test Method for Puncture-Propagation Tear Resistance of Plastic Film and Thin Sheeting
ASTM D 3985 : 2002 Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor
ASTM D 1894 : 2006 Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting
ASTM D 1003 : 1992 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
ASTM D 2838 : 2009 Standard Test Method for Shrink Tension and Orientation Release Stress of Plastic Film and Thin Sheeting
ASTM D 3985 : 2017 Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor
ASTM D 257 : 2014 : R2021 : EDT 1 Standard Test Methods for DC Resistance or Conductance of Insulating Materials
ASTM D 2457 : 2021 Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics
ASTM D 2457 : 2008 : EDT 1 Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics
ASTM D 1938 : 2019 Standard Test Method for Tear-Propagation Resistance (Trouser Tear) of Plastic Film and Thin Sheeting by a Single-Tear Method
ASTM D 1922 : 2006 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 2838 : 2002 Standard Test Method for Shrink Tension and Orientation Release Stress of Plastic Film and Thin Sheeting
ASTM D 7192 : 2008 : REV A Standard Test Method for High Speed Puncture Properties of Plastic Films Using Load and Displacement Sensors
ASTM D 2275 : 1995 Standard Test Method for Voltage Endurance of Solid Electrical Insulating Materials Subjected to Partial Discharges (Corona) on the Surface
ASTM D 2578 : 2004 : REV A Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films
ASTM D 1709 : 2015 : REV A Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 1004 : 2021 Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting
ASTM D 1922 : 2009 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 1434 : 1982 : R1998 Standard Test Method for Determining Gas Permeability Characteristics of Plastic Film and Sheeting
ASTM D 2176 : 1997 Standard Test Method for Folding Endurance of Paper by the M.I.T. Tester
ASTM D 3892 : 2015 : REDLINE PRACTICE FOR PACKAGING/PACKING OF PLASTICS
ASTM D 1709 : 2016 : REV A Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 2275 : 2014 : REDLINE Standard Test Method for Voltage Endurance of Solid Electrical Insulating Materials Subjected to Partial Discharges (Corona) on the Surface
ASTM E 29 : 2022 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.