• There are no items in your cart

ASTM D 8161 : 2017

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Impact Resistance of Thermoplastic Pavement Marking Materials over a Highway Substrate by Means of a Striker Impacted by a Falling Weight
Superseded date

12-27-2022

Published date

04-17-2018

CONTAINED IN VOL. 06.02, 2018 Describes the sample preparation over a road-type substrate and test methodology of thermoplastic pavement marking materials similar to the 'Gardner Impact' method as listed in Test Method D5420.

1.1This test method covers the sample preparation over a road-type substrate and test methodology of thermoplastic pavement marking materials similar to the “Gardner Impact” method as listed in Test Method D5420.

1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 01
DocumentType
Test Method
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

ASTM D 5420 : 1998 : REV A Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact)
ASTM E 177 : 1990 : REV A : R1996 Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods
ASTM E 177 : 2014 : REDLINE Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods
ASTM D 4796 : 2017 Standard Test Method for Bond Strength of Thermoplastic Pavement Marking Materials
ASTM D 5420 : 2010 Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact)
ASTM D 7308 : 2017 : REDLINE Standard Practice for Sample Preparation of Thermoplastic Pavement Marking Materials
ASTM D 7308 : 2017 Standard Practice for Sample Preparation of Thermoplastic Pavement Marking Materials
ASTM D 4796 : 1988 : R2004 Standard Test Method for Bond Strength of Thermoplastic Traffic Marking Materials
ASTM D 7307 : 2006 : R2011 Standard Practice for Sampling of Thermoplastic Traffic Marking Materials
ASTM D 883 : 2022 Standard Terminology Relating to Plastics
ASTM D 883 : 2020 : REV B Standard Terminology Relating to Plastics
ASTM E 284 : 2022 Standard Terminology of Appearance
ASTM D 2794 : 1992 Standard Test Method for Resistence of Organic Coatings to the Effects of Rapid Deformation (Impact)
ASTM E 691 : 2020 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 5420 : 2004 Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact)
ASTM D 4796 : 2010 Standard Test Method for Bond Strength of Thermoplastic Traffic Marking Materials
ASTM D 5628 : 2018 Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimens by Means of a Falling Dart (Tup or Falling Mass)
ASTM E 284 : 2017 : REDLINE Standard Terminology of Appearance
ASTM D 5628 : 2006 Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimens by Means of a Falling Dart (Tup or Falling Mass)
ASTM E 691 : 2019 : EDT 1 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 7308 : 2007 : R2012 Standard Practice for Sample Preparation of Thermoplastic Traffic Marking Materials
ASTM D 4796 : 2017 : REDLINE Standard Test Method for Bond Strength of Thermoplastic Pavement Marking Materials
ASTM D 7307 : 2021 Standard Practice for Sampling of Thermoplastic Pavement Marking Materials
ASTM E 691 : 2022 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 2794 : 1993 : R1999 : EDT 1 Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact)
ASTM E 691 : 2009 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 2794 : 1993 : R2004 Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact)
ASTM D 7308 : 2007 Standard Practice for Sample Preparation of Thermoplastic Traffic Marking Materials
ASTM D 7307 : 2006 Standard Practice for Sampling of Thermoplastic Traffic Marking Materials
ASTM E 691 : 2021 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 2794 : 1993 TEST METHOD FOR RESISTANCE OF ORGANIC COATINGS TO THE EFFECTS OF RAPID DEFORMATION (IMPACT)
ASTM D 5628 : 1996 Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimens by Means of a Falling Dart (Tup or Falling Mass)
ASTM D 5420 : 2016 : REDLINE Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact)
ASTM D 5420 : 2021 Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact)
ASTM D 5420 : 2016 Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact)
ASTM D 2794 : 1993 : R2019 Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact)
ASTM D 5628 : 2007 Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimens by Means of a Falling Dart (Tup or Falling Mass)
ASTM D 7307 : 2006 : R2016 Standard Practice for Sampling of Thermoplastic Traffic Marking Materials
ASTM D 2794 : 1993 : R2010 Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact)
ASTM D 4796 : 1988 : R1998 Standard Test Method for Bond Strength of Thermoplastic Traffic Marking Materials
ASTM E 284 : 2017 Standard Terminology of Appearance
ASTM D 5628 : 2010 Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimens by Means of a Falling Dart (Tup or Falling Mass)

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.