• There are no items in your cart

ASTM E 1514 : 1998 : R2017 : EDT 1

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Structural Standing Seam Steel Roof Panel Systems
Available format(s)

Hardcopy , PDF

Superseded date

01-09-2024

Language(s)

English

Published date

11-08-2017

CONTAINED IN VOL. 04.11, 2017 Defines the design, construction, and weatherability of structural standing seam steel roof panel systems. It includes performance requirements for the following elements only: panels, concealed panel clips, panel/clip anchorage, and panel joint sealers.

1.1This specification covers the design, construction, and weatherability of structural standing seam steel roof panel systems. It includes performance requirements for the following elements only: panels, concealed panel clips, panel/clip anchorage, and panel joint sealers.

Note 1:These systems are used on both low-slope and steep-slope roof applications. They also are used with or without an underlying deck or sheathing.

1.2The objective of this specification is to provide for the overall performance of the structural standing seam steel roof panel system as defined in 3.2.6 during its service life in order to provide weather protection, carry the specified design loads, and allow proper access over the roof surface in order to provide for periodic maintenance of equipment by the owner.

1.3In addition to structural, the specifier shall evaluate other characteristics beyond the scope of this specification that affect the final choice of roof construction. These include, but are not limited to, functional, legal, insurance, and economic considerations. See Appendix X1 for specifier's checklist.

1.4The specification is not intended to exclude products or systems not covered by the referenced documents.

1.5The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.6The text of this specification contains notes and footnotes that provide explanatory information and are not requirements of this specification.

1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
E 06
DocumentType
Standard
Pages
5
ProductNote
Reconfirmed EDT 1
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM A 875/A875M : 2013 Standard Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-Coated by the Hot-Dip Process
ASTM C 765 : 1997 : R2015 Standard Test Method for Low-Temperature Flexibility of Preformed Tape Sealants
ASTM C 711 : 2022 Standard Test Method for Low-Temperature Flexibility and Tenacity of One-Part, Elastomeric, Solvent-Release Type Sealants
ASTM E 631 : 2015 : REDLINE Standard Terminology of Building Constructions
ASTM A 653/A653M : 2001 : REV A Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process
ASTM E 1592 : 2005 : R2017 Standard Test Method for Structural Performance of Sheet Metal Roof and Siding Systems by Uniform Static Air Pressure Difference
ASTM A 653/A653M : 2023 Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process
ASTM E 1680 : 2016 : REDLINE Standard Test Method for Rate of Air Leakage through Exterior Metal Roof Panel Systems
ASTM A 463/A463M : 2015 : R2020 : EDT 1 Standard Specification for Steel Sheet, Aluminum-Coated, by the Hot-Dip Process
ASTM G 21 : 2015 : REDLINE Standard Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi
ASTM E 1646 : 1995 : R2018 Standard Test Method for Water Penetration of Exterior Metal Roof Panel Systems by Uniform Static Air Pressure Difference
ASTM E 1646 : 1995 : R2003 Standard Test Method for Water Penetration of Exterior Metal Roof Panel Systems by Uniform Static Air Pressure Difference
ASTM E 1592 : 2001 Standard Test Method for Structural Performance of Sheet Metal Roof and Siding Systems by Uniform Static Air Pressure Difference
ASTM C 711 : 2014 : REDLINE Standard Test Method for Low-Temperature Flexibility and Tenacity of One-Part, Elastomeric, Solvent-Release Type Sealants
ASTM A 653/A653M : 2022 Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process
ASTM D 3310 : 2000 : R2006 Standard Test Method for Determining Corrosivity of Adhesive Materials
ASTM A 875/A875M : 2013 : REDLINE Standard Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-Coated by the Hot-Dip Process
ASTM A 792/A792M : 2009 Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process
ASTM A 653/A653M : 2020 Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process
ASTM E 1646 : 1995 Standard Test Method for Water Penetration of Exterior Metal Roof Panel Systems by Uniform Static Air Pressure Difference
ASTM D 1667 : 1976 : R1990 Standard Specification for Flexible Cellular MaterialsÐVinyl Chloride Polymers and Copolymers (Closed-Cell Foam)
ASTM A 875/A875M : 2013 : R2021 Standard Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-Coated by the Hot-Dip Process
ASTM D 1667 : 2005 Standard Specification for Flexible Cellular Materials-Vinyl Chloride Polymers and Copolymers (Closed-Cell Foam)
ASTM D 1667 : 1997 Standard Specification for Flexible Cellular Materials-Vinyl Chloride Polymers and Copolymers (Closed-Cell Foam)
ASTM E 1646 : 1995 : R2011 Standard Test Method for Water Penetration of Exterior Metal Roof Panel Systems by Uniform Static Air Pressure Difference
ASTM A 792/A792M : 2022 Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process
ASTM E 1680 : 2011 Standard Test Method for Rate of Air Leakage Through Exterior Metal Roof Panel Systems
ASHRAE HDBK FUNDAMENTALS : 2013 ASHRAE HANDBOOK - FUNDAMENTALS
ASTM A 875/A875M : 2023 Standard Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-Coated by the Hot-Dip Process
ASTM A 463/A463M : 2022 Standard Specification for Steel Sheet, Aluminum-Coated, by the Hot-Dip Process
ASTM D 1667 : 2022 Standard Specification for Flexible Cellular Materials—Poly (Vinyl Chloride) Foam (Closed-Cell)
ASTM A 463/A463M : 2015 : REDLINE Standard Specification for Steel Sheet, Aluminum-Coated, by the Hot-Dip Process
ASTM D 3310 : 2000 Standard Test Method for Determining Corrosivity of Adhesive Materials
ASTM A 875/A875M : 2022 Standard Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-Coated by the Hot-Dip Process
ASTM D 3310 : 2000 : R2023 Standard Test Method for Determining Corrosivity of Adhesive Materials
ASTM E 1592 : 1998 Standard Test Method for Structural Performance of Sheet Metal Roof and Siding Systems by Uniform Static Air Pressure Difference
ASTM C 711 : 2014 Standard Test Method for Low-Temperature Flexibility and Tenacity of One-Part, Elastomeric, Solvent-Release Type Sealants
ASTM C 765 : 2023 Standard Test Method for Low-Temperature Flexibility of Preformed Tape Sealants
ASTM E 1680 : 2016 Standard Test Method for Rate of Air Leakage through Exterior Metal Roof Panel Systems
ASTM D 1667 : 2005 : R2011 Standard Specification for Flexible Cellular Materials<char: emdash>Poly (Vinyl Chloride) Foam (Closed-Cell)
ASTM A 792/A792M : 2010 : R2015 Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process
ASTM D 3310 : 2000 : R2014 Standard Test Method for Determining Corrosivity of Adhesive Materials
ASTM A 792/A792M : 2023 Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process
FM 4471 : 2010 CLASS 1 PANEL ROOFS
ASTM A 875/A875M : 2021 Standard Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-Coated by the Hot-Dip Process
ASTM D 1667 : 2017 : REDLINE Standard Specification for Flexible Cellular Materials—Poly (Vinyl Chloride) Foam (Closed-Cell)
ASTM A 792/A792M : 2021 : REV A Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process
ASTM E 1680 : 1995 Standard Test Method for Rate of Air Leakage Through Exterior Metal Roof Panel Systems
ASTM A 875/A875M : 2009 Standard Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-Coated by the Hot-Dip Process
ASTM G 21 : 2015 Standard Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi
UL 580:5ED 2006-11 Standard for Tests for Uplift Resistance of Roof Assemblies
ASTM A 792/A792M : 2021 Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process
ASTM E 1592 : 2005 Standard Test Method for Structural Performance of Sheet Metal Roof and Siding Systems by Uniform Static Air Pressure Difference
ASTM G 21 : 2015 : R2021 : EDT 1 Standard Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi
ASTM D 1667 : 2017 Standard Specification for Flexible Cellular Materials—Poly (Vinyl Chloride) Foam (Closed-Cell)
ASTM E 1680 : 2016 : R2022 Standard Test Method for Rate of Air Leakage through Exterior Metal Roof Panel Systems
ASTM E 1592 : 2005 : R2012 Standard Test Method for Structural Performance of Sheet Metal Roof and Siding Systems by Uniform Static Air Pressure Difference

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.