ASTM E 155 : 2015 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
08-10-2020
English
09-01-2015
CONTAINED IN VOL. 03.03, 2017 Describes the types and degrees of discontinuities that may be found in aluminum-alloy and magnesium-alloy castings.
1.1These reference radiographs illustrate the types and degrees of discontinuities that may be found in aluminum-alloy and magnesium-alloy castings. The castings illustrated are in thicknesses of 1/4in. (6.35 mm) and 3/4in. (19.1 mm). The reference radiograph films are an adjunct to this document and must be purchased separately from ASTM International if needed.
1.2These film reference radiographs are not intended to illustrate the types and degrees of discontinuities found in aluminum-alloy and magnesium-alloy castings when performing digital radiography. If performing digital radiography of aluminum-alloy castings, refer to Digital Reference Image Standard E2422. If performing digital radiography of magnesium-alloy castings, refer to Digital Reference Image Standard E2869.
1.3This document may be used where no other applicable document exists, for other material thicknesses for which it has been found to be applicable and for which agreement has been reached between the purchaser and the manufacturer.
1.4From time to time, there may be minor changes to the process for manufacturing of the reference radiograph adjunct materials. These changes could include changes in the films or processing chemicals used, changes in the dies or printing for the cardboard mats, etc.; however, in all cases, these changes are reviewed by the Illustration Monitoring Subcommittee and all reference radiographs are reviewed against a fixed prototype image to ensure that there are no changes to the acceptance level represented by the reference radiographs. Therefore, the adjunct reference radiographs remain valid for use with this standard regardless of the date of production or the revision level of the text standard.
1.5The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1:Vol I: The set of reference radiographs consists of 13 plates covering discontinuities in aluminum-alloy castings and 10 plates covering discontinuities in magnesium-alloy castings. Each plate is held in an 81/2by 11-in. (216 by 279-mm) cardboard frame and each plate illustrates eight grades of severity for the discontinuity in approximately a 2 by 2-in. (51 by 51-mm) area. The cardboard frames are contained in a 101/2by 111/2-in. (267 by 292-mm) ring binder. The reference radiographs are not impacted by this revision. There have been no revisions to the adjunct reference radiographs since original issue. The adjunct reference radiographs of any issue remain valid and may be used to this standard.
Vol. II: The set of reference radiographs consists of four plates covering discontinuities in magnesium-alloy castings only. Each plate is held in an 81/2by 11-in. (216 by 279-mm) cardboard frame and illustrates eight grades of severity for the discontinuity (with the exception of discrete discontinuities, where only one example of each discontinuity is given).
Note 2:Reference radiographs applicable to aluminum and magnesium die castings up to 1 in. (25 mm) in thickness are contained in Reference Radiographs E505.
| Committee |
E 07
|
| DevelopmentNote |
Supersedes ASTM E 98 (12/2001)
|
| DocumentType |
Redline
|
| Pages |
5
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
| SAE AS 7114/4 : 2008 | NADCAP REQUIREMENTS FOR NONDESTRUCTIVE TESTING FACILITY RADIOGRAPHY |
| ASTM B 199 : 2017 : REDLINE | Standard Specification for Magnesium-Alloy Permanent Mold Castings |
| MIL-STD-2175 Revision A:1993 | CASTING, CLASSIFICATION AND INSPECTION OF |
| MIL-STD-1689 Revision A:1990 | FABRICATION, WELDING AND INSPECTION OF SHIPS STRUCTURE |
| SAE AMS 4240 : 1982 | CASTINGS, SAND - 10MG, SOLUTION HEAT TREATED & NATURALLY AGED |
| SAE AMS A 21180 : 2017 | ALUMINUM-ALLOY CASTINGS, HIGH STRENGTH |
| DIN EN 2002-21:2000-07 (Draft) | AEROSPACE SERIES - METALLIC MATERIALS; TEST METHODS - PART 21: RADIOGRAPHIC TESTING OF CASTINGS |
| SAE AMS 4222 : 2017 | ALUMINUM ALLOY CASTINGS, SAND, MODERATE HEAT RESISTANCE 4.0CU - 2.0NI - 1.5MG - 0.12TI (242.0P) SOLUTION HEAT TREATED AND STABILIZED |
| BS 5L 101:2011 | Procedure for inspection, testing and acceptance of aluminium-base and magnesium-base ingots and castings |
| MIL-C-47269 Revision A:1992 | CASTINGS, INSPECTION OF (FOR GUIDED MISSILE AND ROCKET MATERIAL) |
| ASTM E 1030 : 2005 : R2011 | Standard Test Method for Radiographic Examination of Metallic Castings |
| 99/710246 DC : JUL 99 | PREN 2002-21 - AEROSPACE SERIES - METALLIC MATERIALS - TEST METHODS - PART 21: RADIOGRAPHIC TESTING OF CASTINGS |
| MIL-Q-45970 Revision A:1975 | QUALITY ASSURANCE FOR WEAPONS AND SUPPORT MATERIAL |
| SAE AMS 4241 : 2015 | ALUMINUM ALLOY CASTINGS, 7.0SI - 0.58MG - 0.15TI - 0.06BE (D357.0-T6), SOLUTION AND PRECIPITATION HEAT TREATED, DENDRITE ARM SPACING (DAS) CONTROLLED |
| ISO 9915:1992 | Aluminium alloy castings Radiography testing |
| BS 4L 101:1990 | Procedure for inspection, testing and acceptance of aluminium-base and magnesium-base ingots and castings |
| ASTM E 2869 : 2017 : REDLINE | Standard Digital Reference Images for Magnesium Castings |
| EN 50052:2016 | High-voltage switchgear and controlgear - Gas-filled cast aluminium alloy enclosures |
| EN 12681-1:2017 | Founding - Radiographic testing - Part 1: Film techniques |
| EN 12681 : 2003 | FOUNDING - RADIOGRAPHIC EXAMINATION |
| MIL-A-21180 Revision D:1984 | ALUMINUM-ALLOY CASTINGS, HIGH STRENGTH |
| DEFSTAN 07-85(PT1)/3(2006) : 2006 | DESIGN REQUIREMENTS FOR WEAPONS AND ASSOCIATED SYSTEMS - PART 1: MANDATORY DESIGN REQUIREMENTS |
| CSA C83 : 2017 | COMMUNICATION AND POWER LINE HARDWARE |
| MIL-W-63150 Base Document:1977 | WEAPONS AND SUPPORT MATERIAL STANDARD QUALITY ASSURANCE PROVISIONS FOR |
| MIL-STD-278 Revision F:1987 | WELDING AND CASTING STANDARD |
| 17/30244737 DC : 0 | BS EN 17149 - RAILWAY APPLICATIONS - FATIGUE STRENGTH ASSESSMENT OF RAILWAY VEHICLE STRUCTURES BASED ON CUMULATIVE DAMAGE |
| BS EN 50052:2016 | High-voltage switchgear and controlgear. Gas-filled cast aluminium alloy enclosures |
| SAE MAM 4427 : 2003 | MAGNESIUM ALLOY SAND CASTINGS 4.0Y - 2.3ND - 0.7ZR (WE43A - T6) SOLUTION AND PRECIPITATION HEAT TREATED |
| SAE AMS 4227 : 1988 | ALUMINUM ALLOY, CASTINGS SAND, 8.0CU 6.0MG 0.50MN 0.50NI, AS CAST |
| SAE AMS 4429 : 2012 | MAGNESIUM ALLOY CASTINGS, SAND 2.8ND - 1.4GD - 0.4ZN - 0.6ZR (EV31A - T6), SOLUTION AND PRECIPITATION HEAT TREATED |
| ASTM E 2736 : 2017 : REDLINE | Standard Guide for Digital Detector Array Radiography |
| ASTM B 80 : 2015 : REDLINE | Standard Specification for Magnesium-Alloy Sand Castings |
| NASA MSFC STD 100 : 1961 | CASTING, ALUMINIUM AND MAGNESIUM ALLOY, RADIOGRAPHIC INSPECTION OF, ACCEPTANCE STANDARD FOR |
| ASME B31.3:2016 | PROCESS PIPING |
| ASTM B 403 : 2012 : REDLINE | Standard Specification for Magnesium-Alloy Investment Castings |
| SAE AMS 4249B : 2012 (R2018) | ALUMINUM ALLOY CASTINGS 7.0SI - 0.58MG - 0.15TI - 0.06BE (D357.0-T6) SOLUTION AND PRECIPITATION HEAT TREATED (REQUIRING FATIGUE AND FRACTURE TOUGHNESS TESTING) |
| SAE AMS 4424 : 2014 | Magnesium Alloy Castings, Sand 6.0Al - 3.0Zn (AZ63-T6) Solution and Precipitation Heat Treated |
| SAE AMS 4418 : 2012 | MAGNESIUM ALLOY, SAND CASTINGS, 2.5AG - 2.1DI - 0.70ZR (QE22A-T6), SOLUTION AND PRECIPITATION HEAT TREATED |
| MIL-M-46143 Base Document:1988 | MAGNESIUM LITHIUM ALLOY CASTINGS (LS141A AND LZ145A) |
| 15/30303100 DC : 0 | BS EN 50052 - CAST ALUMINIUM ALLOY ENCLOSURES FOR GAS-FILLED HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR |
| MIL-P-45971 Base Document:1975 | PRODUCT ENGINEERING QUALITY ENGINEERING SYSTEM (PEQES) FOR WEAPONS AND SUPPORT MATERIAL |
| SAE AMS 4482 : 2012 | CAST ALUMINUM ALLOY COMPOSITE 4.6 CU - 3.4TI - 1.4B - 0.75AG - 0.27MG (A205.0/TIB2/3P-T7P) SAND CAST, SOLUTION AND PRECIPITATION HEAT TREATED |
| SAE AMS 4417 : 2018 | CASTINGS, SAND, MAGNESIUM ALLOY, 1.5AG - 2.1DI - 0.08CU - 0.70ZR (EQ21A - T6), SOLUTION AND PRECIPITATION HEAT TREATED |
| SAE AMS 4443 : 2017 | MAGNESIUM ALLOY, SAND CASTINGS, 4.5ZN - 0.75ZR (ZK51A-T5) PRECIPITATION HEAT TREATED |
| SAE AMS 7918 : 2016 | BERYLLIUM ALUMINUM ALLOY INVESTMENT CASTINGS, 64.9BE - 30AL - 3AG - 1CO - 0.75GE, AS CAST |
| SAE AS 7100/1 : 2008 | NATIONAL AEROSPACE AND DEFENSE CONTRACTORS ACCREDITATION PROGRAM (NADCAP) SURVEY CHECKLISTS FOR THE NDT SUPPLIERS ACCREDITATION PROGRAM |
| SAE AMS 4231 : 1983 | CASTINGS, SAND - 4.5CU - 1.1SI, SOLUTION AND PRECIPITATION HEAT TREATED |
| ASTM E 1030/E1030M : 2015 : REDLINE | Standard Practice for Radiographic Examination of Metallic Castings |
| BS EN 12681-1:2017 | Founding. Radiographic testing Film techniques |
| ASTM E 2422 : 2017 : REDLINE | Standard Digital Reference Images for Inspection of Aluminum Castings |
| ASTM E 1030 : 2005 | Standard Test Method for Radiographic Examination of Metallic Castings |
| DIN EN 12681:2003-06 | FOUNDING - RADIOGRAPHIC EXAMINATION |
| CSA C22.2 No. 145 : 2011 | ELECTRIC MOTORS AND GENERATORS FOR USE IN HAZARDOUS (CLASSIFIED) LOCATIONS |
| CSA C22.2 No. 145 : 2011 : INC : UPD 1 : 2017 : R201500 | ELECTRIC MOTORS AND GENERATORS FOR USE IN HAZARDOUS (CLASSIFIED) LOCATIONS |
| CSA C22.2 No. 145 : 2011 : R2015 | ELECTRIC MOTORS AND GENERATORS FOR USE IN HAZARDOUS (CLASSIFIED) LOCATIONS |
| SAE AMS 4219 : 2015 | ALUMINUM ALLOY CASTINGS, 7.0SI - 0.55MG - 0.12TI - 0.06BE (A357.0 T6), SOLUTION AND PRECIPITATION HEAT TREATED |
| DIN 29531:1990-09 | Aerospace; castings of aluminium and magnesium alloys; technical specification |
| PREN 50052 : DRAFT 2015 | CAST ALUMINIUM ALLOY ENCLOSURES FOR GAS-FILLED HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR |
| I.S. EN 12681:2003 | FOUNDING - RADIOGRAPHIC EXAMINATION |
| ASTM F 3318 : 2018 | Standard for Additive Manufacturing – Finished Part Properties – Specification for AlSi10Mg with Powder Bed Fusion – Laser Beam |
| SAE AMS 4439 : 2012 | MAGNESIUM ALLOY CASTINGS, 4.2ZN - 1.2 RARE EARTHS - 0.7ZR (ZE41A-T5), PRECIPITATION HEAT TREATED |
| ASTM E 1648 : 2015 : REDLINE | Standard Reference Radiographs for Examination of Aluminum Fusion Welds |
| SAE AMS 2175 : 2010 | CASTINGS, CLASSIFICATION AND INSPECTION OF |
| MIL-STD-453 Revision C:1984 | INSPECTION, RADIOGRAPHIC |
| I.S. EN 12681-1:2017 | FOUNDING - RADIOGRAPHIC TESTING - PART 1: FILM TECHNIQUES |
| SAE AMS 4420 : 2017 | MAGNESIUM ALLOY CASTINGS, SAND, 6AL - 3ZN (AZ63A-F), AS CAST |
| SAE AMS 4427 : 2012 | MAGNESIUM ALLOY CASTINGS, SAND, 4.0Y - 2.3ND - 0.7ZR (WE43B - T6), SOLUTION AND PRECIPITATION HEAT TREATED |
| SAE AMS 4442 : 2012 | MAGNESIUM ALLOY SAND CASTINGS, 3.2 RARE EARTHS - 2.5ZN - 0.70ZR (EZ33A-T5), PRECIPITATION HEAT TREATED |
| PREN 2002-21 : 200P2 | AEROSPACE SERIES - METALLIC MATERIALS - TEST METHODS - PART 21: RADIOGRAPHIC TESTING OF CASTINGS |
| SAE AMS 4242 : 2015 | ALUMINUM ALLOY, CASTINGS, 4.7CU - 0.60AG - 0.35MN - 0.25MG - 0.25TI (B201.0-T7), SOLUTION HEAT TREATED AND OVERAGED |
| SAE AMS 4434 : 2017 | MAGNESIUM ALLOY CASTINGS, SAND, 9.0AL - 2.0ZN (AZ92A-T6), SOLUTION AND PRECIPITATION HEAT TREATED |
| BS EN 12681:2003 | Founding. Radiographic examination |
| BS EN 13981-3:2006 | Aluminium and aluminium alloys. Products for structural railway applications. Technical conditions for inspection and delivery Castings |
| EN 13981-3:2006 | Aluminium and aluminium alloys - Products for structural railway applications - Technical conditions for inspection and delivery - Part 3: Castings |
| MIL-M-46062 Revision C:1985 | MAGNESIUM ALLOY CASTINGS, HIGH STRENGTH |
| 04/30050372 DC : DRAFT JUN 2004 | EN 13981-3 - ALUMINIUM AND ALUMINIUM ALLOYS - PRODUCTS FOR STRUCTURAL RAILWAY APPLICATIONS - TECHNICAL CONDITIONS FOR INSPECTION AND DELIVERY - PART 3: CASTINGS |
| SAE AMS 4440 : 1999 | MAGNESIUM ALLOY CASTINGS, SAND 3.5CE - 0.70ZR (EK41A-T5) PRECIPITATION HEAT TREATED |
| SAE AMS 4426 : 2013 | CASTINGS, SAND, MAGNESIUM ALLOY 5.1Y - 3.0RE - 0.70ZR (WE54-T6) SOLUTION AND PRECIPITATION HEAT TREATED |
| SAE AMS T 81915 : 2016 | TITANIUM AND TITANIUM-ALLOY CASTINGS, INVESTMENT |
| SAE AMS 4444 : 2017 | MAGNESIUM ALLOY CASTINGS, SAND, 6.0ZN - 0.80ZR (ZK61A-T5), PRECIPITATION HEAT TREATED |
| SAE AMS 4471 : 2014 | CAST ALUMINUM ALLOY COMPOSITE 4.6CU - 3.4TI - 1.4B - 0.75AG - 0.27MG (205.0/TIB[2]/3P-T7P) INVESTMENT CAST, SOLUTION AND PRECIPITATION HEAT TREATED |
| SAE AMS 4275 : 2017 | CASTINGS, PERMANENT MOLD, 6.2SN - 1CU - 1NI, STRESS RELIEVED |
| SAE AMS 4425 : 2017 | MAGNESIUM ALLOY CASTINGS, SAND, 5.8ZN - 2.5RE - 0.70ZR (ZE63-T6), SOLUTION AND PRECIPITATION HEAT TREATED |
| SAE AMS 4288 : 2016 | ALUMINUM ALLOY CASTINGS, 7.0SI - 0.58MG - 0.15TI (E357.0-T6), SOLUTION AND PRECIPITATION HEAT TREATED |
| SAE AMS STD 2175 : 2003 | CASTINGS, CLASSIFICATION AND INSPECTION OF |
| SAE AMS 4437 : 2014 | MAGNESIUM ALLOY CASTINGS, SAND, 8.7AL - 0.70ZN (AZ91C-T6), SOLUTION HEAT TREATED AND AGED |
| ASTM E 505 : 2015 : REDLINE | Standard Reference Radiographs for Inspection of Aluminum and Magnesium Die Castings |
| ASME B31.3 SPANISH : 2010 | PROCESS PIPING |
| ASTM E 2869 : 2017 : REDLINE | Standard Digital Reference Images for Magnesium Castings |
| ASTM E 505 : 2015 : REDLINE | Standard Reference Radiographs for Inspection of Aluminum and Magnesium Die Castings |
| ASTM E 2422 : 2017 : REDLINE | Standard Digital Reference Images for Inspection of Aluminum Castings |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.