• There are no items in your cart

ASTM E 1645 : 2016 : REDLINE

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Practice for Preparation of Dried Paint Samples by Hotplate or Microwave Digestion for Subsequent Lead Analysis
Available format(s)

PDF

Superseded date

10-14-2020

Language(s)

English

Published date

03-01-2016

CONTAINED IN VOL. 04.11, 2016 Defines the sample preparation procedures for paint samples that are collected during the assessment, management or control of lead hazards.

1.1This practice covers the sample preparation procedures for paint samples that are collected during the assessment, management or control of lead hazards.

1.2This practice describes the digestion procedures using a hot plate or microwave oven or apparatus for paint samples that are to be analyzed for lead content.

1.3This practice covers the general considerations for quantitative sample extraction for total recoverable lead in dried paint samples (either bulk paint or paint powder) using hot plate or microwave heating techniques, or both.

1.4This practice contains notes that are explanatory and not part of the mandatory requirements of the standard.

1.5This practice is based on two NIOSH Methods, 7082 and 7105, and on an EPA standard operating procedure for lead in paint.

1.6The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 6.1.2, 6.1.2.1, 6.1.2.2, 6.3.2.4, 7.2.1, and 7.2.2.

Committee
D 22
DevelopmentNote
Supersedes ASTM ES 37 (12/2001)
DocumentType
Redline
Pages
7
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

PD CEN/TR 16741:2015 Textiles and textile products. Guidance on health and environmental issues related to chemical content of textile products intended for clothing, interior textiles and upholstery
ASTM A 1109 : 2018 Standard Specification for Special Fittings for Single-Stack Hubless Cast Iron Soil Pipe Fittings for Sanitary, Waste, and Vent Piping Applications
ASTM E 1583 : 2017 Standard Practice for Evaluating Laboratories Engaged in Determination of Lead in Paint, Dust, Airborne Particulates, and Soil Taken From and Around Buildings and Related Structures
ASTM D 7876 : 2013 Standard Practice for Practice for Sample Decomposition Using Microwave Heating (With or Without Prior Ashing) for Atomic Spectroscopic Elemental Determination in Petroleum Products and Lubricants
ASTM E 631 : 2015 : REDLINE Standard Terminology of Building Constructions
ASTM E 2119 : 2016 Standard Practice for Quality Systems for Conducting In Situ Measurements of Lead Content in Paint or Other Coatings Using Field-Portable X-Ray Fluorescence (XRF) Devices
ASTM E 1828 : 2001 Standard Practice for Evaluating the Performance Characteristics of Qualitative Chemical Spot Test Kits for Lead in Paint (Withdrawn 2010)
ASTM E 2051 : 2001 Standard Practice for the Determination of Lead in Paint, Settled Dust, Soil and Air Particulate by Field-Portable Electroanalysis (Withdrawn 2010)
ASTM E 2052 : 1999 Standard Guide for Evaluation, Management, and Control of Lead Hazards in Facilities (Withdrawn 2008)
ASTM E 2115 : 2015 Standard Guide for Conducting Lead Hazard Assessments of Dwellings and of Other Child-Occupied Facilities
ASTM E 1775 : 2016 : REDLINE Standard Guide for Evaluating Performance of On-Site Extraction and Field-Portable Electrochemical or Spectrophotometric Analysis for Lead
ASTM A 74 : 2017 : REDLINE Standard Specification for Cast Iron Soil Pipe and Fittings
S.R. CEN/TR 16741:2015 TEXTILES AND TEXTILE PRODUCTS - GUIDANCE ON HEALTH AND ENVIRONMENTAL ISSUES RELATED TO CHEMICAL CONTENT OF TEXTILE PRODUCTS INTENDED FOR CLOTHING, INTERIOR TEXTILES AND UPHOLSTERY
ASTM E 1613 : 2012 : REDLINE Standard Test Method for Determination of Lead by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES), Flame Atomic Absorption Spectrometry (FAAS), or Graphite Furnace Atomic Absorption Spectrometry (GFAAS) Techniques
CEN/TR 16741:2015 Textiles and textile products - Guidance on health and environmental issues related to chemical content of textile products intended for clothing, interior textiles and upholstery

ASTM D 1129 : 2013 : REDLINE Standard Terminology Relating to Water
ISO 8655-1:2002 Piston-operated volumetric apparatus Part 1: Terminology, general requirements and user recommendations
ISO 1042:1998 Laboratory glassware One-mark volumetric flasks
ASTM E 1729 : 2016 Standard Practice for Field Collection of Dried Paint Samples for Subsequent Lead Determination
ISO Guide 30:2015 Reference materials Selected terms and definitions

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.