• There are no items in your cart

ASTM E 1783/E1783M : 1996 : R2017

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Preformed Architectural Strip Seals for Buildings and Parking Structures
Available format(s)

Hardcopy , PDF

Superseded date

03-22-2024

Language(s)

English

Published date

09-07-2017

CONTAINED IN VOL. 04.12, 2017 Defines the physical requirements for the fully cured elastomeric alloy and the movement capabilities of preformed architectural compression seals used for sealing expansion joints in buildings and parking structures.

1.1This specification covers the physical requirements for the fully cured elastomeric alloy and the movement capabilities of preformed architectural compression seals used for sealing expansion joints in buildings and parking structures. The preformed architectural strip seal is an elastomeric extrusion. This extrusion is either a membrane or tubular having an internal baffle system produced continuously and longitudinally throughout the material. These extrusions are secured in or over a joint by locking rails or an end dam nosing material. The architectural strip seal is compressed and expanded by this mechanical or chemical attachment.

Note 1:Movement capability is defined in Test Method E1399/E1399M.

1.2This specification covers all colors of architectural strip seals.

Note 2:The products described in this specification are manufactured from thermoplastic elastomers defined as “fully cured elastomeric alloys” in Test Method D5048.

1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
E 06
DevelopmentNote
Supersedes ASTM E 1783. (09/2013)
DocumentType
Standard
Pages
5
ProductNote
Reconfirmed 2017
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM E 631 : 2015 Standard Terminology of Building Constructions

ASTM D 2000 : 2003 : REV A : EDT 1 Standard Classification System for Rubber Products in Automotive Applications
ASTM D 2000 : 2001 Standard Classification System for Rubber Products in Automotive Applications
ASTM D 2240 : 2000 Standard Test Method for Rubber Property—Durometer Hardness
ASTM D 1052 : 2005 Standard Test Method for Measuring Rubber Deterioration-Cut Growth Using Ross Flexing Apparatus
ASTM D 471 : 2016 : REV A Standard Test Method for Rubber Property—Effect of Liquids
ASTM E 631 : 2015 : REDLINE Standard Terminology of Building Constructions
ASTM D 1149 : 2016 Standard Test Methods for Rubber Deterioration—Cracking in an Ozone Controlled Environment
ASTM D 3183 : 2010 Standard Practice for Rubber<span class='unicode'>—</span>Preparation of Pieces for Test Purposes from Products
ASTM D 2000 : 2000 : EDT 1 Standard Classification System for Rubber Products in Automotive Applications
ASTM D 2000 : 2003 : REV A Standard Classification System for Rubber Products in Automotive Applications
ASTM D 5048 : 2009 Standard Test Method for Measuring the Comparative Burning Characteristics and Resistance to Burn-Through of Solid Plastics Using 125-mm Flame
ASTM D 1149 : 2016-02 TEST METHODS FOR RUBBER DETERIORATION - CRACKING IN AN OZONE CONTROLLED ENVIRONMENT
ASTM D 2240 : 2004 Standard Test Method for Rubber Property—Durometer Hardness
ASTM D 5048 : 2020 Standard Test Method for Measuring the Comparative Burning Characteristics and Resistance to Burn-Through of Solid Plastics Using a 125-mm Flame
ASTM D 3183 : 2009 Standard Practice for Rubber<span class='unicode'>—</span>Preparation of Pieces for Test Purposes from Products
ASTM E 1399/E1399M : 1997 : R2022 Standard Test Method for Cyclic Movement and Measuring the Minimum and Maximum Joint Widths of Architectural Joint Systems
ASTM D 3183 : 201 PRACTICE FOR RUBBER - PREPARATION OF PIECES FOR TEST PURPOSES FROM PRODUCTS
ASTM D 1149 : 2015 Standard Test Methods for Rubber Deterioration—Cracking in an Ozone Controlled Environment
ASTM D 412 : 2016 : EDT 1 Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension
ASTM D 792 : 2013 : REDLINE Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
ASTM D 3183 : 2010 : R2015 Standard Practice for Rubber—Preparation of Pieces for Test Purposes from Products
ASTM E 1399/E1399M : 1997 : R2017 Standard Test Method for Cyclic Movement and Measuring the Minimum and Maximum Joint Widths of Architectural Joint Systems
ASTM D 1149 : 2007 Standard Test Methods for Rubber Deterioration-Cracking in an Ozone Controlled Environment
ASTM D 2240 : 2004 : EDT 1 Standard Test Method for Rubber Property—Durometer Hardness
ASTM D 471 : 2016 : REV A : R2021 Standard Test Method for Rubber Property—Effect of Liquids
ASTM D 3183 : 2007 Standard Practice for Rubber—Preparation of Product Pieces for Test Purposes from Products
ASTM D 5048 : 2003 Standard Test Method for Measuring the Comparative Burning Characteristics and Resistance to Burn-Through of Solid Plastics Using 125-mm Flame
ASTM D 2000 : 2008 Standard Classification System for Rubber Products in Automotive Applications
ASTM D 2000 : 2006 Standard Classification System for Rubber Products in Automotive Applications
ASTM D 412 : 2016 Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension
ASTM D 2000 : 2006 : REV A Standard Classification System for Rubber Products in Automotive Applications
ASTM D 1149 : 2018 Standard Test Methods for Rubber Deterioration—Cracking in an Ozone Controlled Environment
ASTM D 2240 : 2015 : R2021 Standard Test Method for Rubber Property—Durometer Hardness
ASTM D 2000 : 2005 Standard Classification System for Rubber Products in Automotive Applications
ASTM D 2000 : 2018 Standard Classification System for Rubber Products in Automotive Applications
ASTM D 2240 : 2002 Standard Test Method for Rubber Property—Durometer Hardness
ASTM D 865 : 2011 Standard Test Method for Rubber<char: emdash>Deterioration by Heating in Air (Test Tube Enclosure)
ASTM D 1052 : 1985 : R1999 : EDT 1 Standard Test Method for Measuring Rubber Deterioration-Cut Growth Using Ross Flexing Apparatus
ASTM D 5048 : 2014 Standard Test Method for Measuring the Comparative Burning Characteristics and Resistance to Burn-Through of Solid Plastics Using a 125-mm Flame
ASTM D 2000 : 2006 : REV A : EDT 1 Standard Classification System for Rubber Products in Automotive Applications
ASTM D 3183 : 1984 : R1998 Standard Practice for Rubber-Preparation of Pieces for Test Purposes from Products
ASTM D 2240 : 2015 Standard Test Method for Rubber Property—Durometer Hardness
ASTM D 2000 : 2012 : R2017 Standard Classification System for Rubber Products in Automotive Applications
ASTM D 1149 : 2007 : R2012 Standard Test Methods for Rubber Deterioration—Cracking in an Ozone Controlled Environment
ASTM D 2240 : 2003 Standard Test Method for Rubber Property—Durometer Hardness
ASTM D 1149 : 1978 : REV A Standard Test Method for Rubber Deterioration - Surface Ozone Cracking In A Chamber ( Flat Specimen)
ASTM D 2240 : 2002 : REV B Standard Test Method for Rubber Property—Durometer Hardness
ASTM D 1052 : 2009 : R2014 Standard Test Method for Measuring Rubber Deterioration—Cut Growth Using Ross Flexing Apparatus
ASTM D 2240 : 2015 : EDT 1 Standard Test Method for Rubber Property—Durometer Hardness
ASTM D 1052 : 2009 Standard Test Method for Measuring Rubber Deterioration-Cut Growth Using Ross Flexing Apparatus
ASTM D 412 : 2016 : R2021 Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension
ASTM D 5048 : 2019 Standard Test Method for Measuring the Comparative Burning Characteristics and Resistance to Burn-Through of Solid Plastics Using a 125-mm Flame
ASTM D 2240 : 2005 Standard Test Method for Rubber Property—Durometer Hardness
ASTM D 2000 : 2004 Standard Classification System for Rubber Products in Automotive Applications
ASTM D 2240 : 2005 : R2010 Standard Test Method for Rubber Property—Durometer Hardness
ASTM D 5048 : 2018 Standard Test Method for Measuring the Comparative Burning Characteristics and Resistance to Burn-Through of Solid Plastics Using a 125-mm Flame
ASTM D 471 : 2016-02 TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS
ASTM D 3183 : 2002 Standard Practice for Rubber—Preparation of Pieces for Test Purposes from Products
ASTM D 2240 : 2002 : REV A Standard Test Method for Rubber Property—Durometer Hardness
ASTM D 3183 : 2010 : R2019 Standard Practice for Rubber—Preparation of Pieces for Test Purposes from Products
ASTM D 1052 : 2009 : R2019 Standard Test Method for Measuring Rubber Deterioration—Cut Growth Using Ross Flexing Apparatus
ASTM D 2000 : 2012 Standard Classification System for Rubber Products in Automotive Applications
ASTM D 2000 : 2003 Standard Classification System for Rubber Products in Automotive Applications
ASTM D 2000 : 2000 Standard Classification System for Rubber Products in Automotive Applications
ASTM D 1149 : 1999 Standard Test Method for Rubber Deterioration-Surface Ozone Cracking in a Chamber
ASTM D 746 : 2014 : REDLINE Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact
ASTM D 5048 : 1997 Standard Test Method for Measuring the Comparative Burning Characteristics and Resistance to Burn-Through of Solid Plastics Using 125-mm Flame

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.