• There are no items in your cart

ASTM E 1797 : 2012

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings
Available format(s)

Hardcopy , PDF

Superseded date

11-11-2014

Language(s)

English

Published date

07-15-2012

CONTAINED IN VOL. 04.11, 2017 Specifies minimum material performance requirements and laboratory test procedures for reinforced liquid coating encapsulation products (single- or multiple-coat systems) for leaded paint in buildings.

1.1 This specification covers minimum material performance requirements and laboratory test procedures for reinforced liquid coating encapsulation products (single- or multiple-coat systems) for leaded paint in buildings. Performance properties addressed in this specification are:

1.1.1 Impact Resistance,

1.1.2 Adhesion,

1.1.3 Dry Abrasion Resistance,

1.1.4 Water Vapor Transmission,

1.1.5 Water and Chemical Resistance,

1.1.6 Surface Burning Characteristics,

1.1.7 Volatile Organic Compound (VOC) Content,

1.1.8 Weathering,

1.1.9 Aging,

1.1.10 Scrub Resistance,

1.1.11 Mildew Resistance,

1.1.12 Paintability/Repairability,

1.2 This specification does not address the selection of an encapsulation product for specific use conditions. Specific use conditions may require performance values other than those stated in this specification. See Guide E1796 for guidance.

1.3 This specification complements Specification E1795 for non-reinforced liquid coating encapsulation products.

1.4 This specification does not cover the use of encapsulation products on industrial steel structures nor residential exterior coated metal surfaces because no corrosion control requirements are included.

1.5 This specification applies to any liquid-applied product incorporating reinforcement materials as part of the system. Reinforcement materials are continuous fabric or mesh and are applied in the field. These materials are typically applied between a base and top coat. These products are used to encapsulate a leaded paint surface with the intent of reducing human exposure to lead in paint.

1.6 The results of the test methods included in this specification will not necessarily predict field performance.

1.7 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
E 06
DevelopmentNote
Supersedes ASTM PS 41 (12/2001)
DocumentType
Standard
Pages
6
ProductNote
Reconfirmed 2012
PublisherName
American Society for Testing and Materials
Status
Superseded
Supersedes

ASTM E 2252 : 2018 Standard Practice for Selection of Lead Hazard Reduction Methods for Identified Risks in Residential Housing or Child Occupied Facilities
ASTM E 1795 : 2017 Standard Specification for Non-Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings
ASTM E 1796 : 2003 : R2016 Standard Guide for Selection and Use of Liquid Coating Encapsulation Products for Leaded Paint in Buildings

ASTM D 2486 : 2017 : REDLINE Standard Test Methods for Scrub Resistance of Wall Paints
ASTM E 1795 : 2017 : REDLINE Standard Specification for Non-Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings
ASTM D 823 : 1995 Standard Practices for Producing Films of Uniform Thickness of Paint, Varnish, and Related Products on Test Panels
ASTM D 3891 : 2008 Standard Practice for Preparation of Glass Panels for Testing Paint, Varnish, Lacquer, and Related Products
ASTM D 4541 : 2017 : REDLINE Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
ASTM D 16 : 2016 : REDLINE TERMINOLOGY FOR PAINT, RELATED COATINGS, MATERIALS, AND APPLICATIONS
ASTM D 4414 : 1995 Standard Practice for Measurement of Wet Film Thickness by Notch Gages
ASTM G 154 : 2016 : REDLINE Standard Practice for Operating Fluorescent Ultraviolet (UV) Lamp Apparatus for Exposure of Nonmetallic Materials
ASTM D 7091 : 2013 : REDLINE Standard Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals
ASTM D 2794 : 1993 TEST METHOD FOR RESISTANCE OF ORGANIC COATINGS TO THE EFFECTS OF RAPID DEFORMATION (IMPACT)
ASTM D 1212 : 1991 Standard Test Methods for Measurement of Wet Film Thickness of Organic Coatings
FED-STD-141 Revision D:2001 PAINT, VARNISH, LACQUER AND RELATED MATERIALS, METHODS OF INSPECTION, SAMPLING AND TESTING
ASTM D 1475 : 2013 : REDLINE Standard Test Method For Density of Liquid Coatings, Inks, and Related Products
ASTM D 3273 : 2016 : REDLINE Standard Test Method for Resistance to Growth of Mold on the Surface of Interior Coatings in an Environmental Chamber
ASTM D 3359 : 2017 : REDLINE Standard Test Methods for Rating Adhesion by Tape Test
ASTM D 1653 : 2013 : REDLINE Standard Test Methods for Water Vapor Transmission of Organic Coating Films

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.