ASTM E 384 : 2017 : REDLINE
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Test Method for Microindentation Hardness of Materials
Available format(s)
PDF
Superseded date
11-12-2022
Language(s)
English
Published date
08-25-2017
CONTAINED IN VOL. 03.01, 2017 Defines determination of the microindentation hardness of materials.
1.1This test method covers determination of the microindentation hardness of materials.
1.2This test method covers microindentation tests made with Knoop and Vickers indenters under test forces in the range from 9.8 × 10-3 to 9.8 N (1 to 1000 gf).
1.3This test method includes an analysis of the possible sources of errors that can occur during microindentation testing and how these factors affect the precision, bias, repeatability, and reproducibility of test results.
1.4Information pertaining to the requirements for direct verification and calibration of the testing machine and the requirements for the manufacture and calibration of Vickers and Knoop reference hardness test blocks are in Test Method E92.
Note 1:While Committee E04 is primarily concerned with metals, the test procedures described are applicable to other materials.
1.5Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Committee |
E 04
|
| DocumentType |
Redline
|
| Pages |
40
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| SAE AMS 4901 : 2015 | TITANIUM SHEET, STRIP, AND PLATE, COMMERCIALLY PURE, ANNEALED, 70.0 KSI (485 MPA) |
| SAE AMS 5925 : 2012 | STEEL, CORROSION -RESISTANT, BARS, WIRE, AND FORGINGS, 15.5CR - 1.8MO - 0.20N (0.37 - 0.45C), ELECTROSLAG REMELTED |
| DIN EN ISO 15156-3:2015-12 | PETROLEUM AND NATURAL GAS INDUSTRIES - MATERIALS FOR USE IN H[2]S-CONTAINING ENVIRONMENTS IN OIL AND GAS PRODUCTION - PART 3: CRACKING-RESISTANT CRAS (CORROSION-RESISTANT ALLOYS) AND OTHER ALLOYS (ISO 15156-3:2015) |
| 07/30172770 DC : 0 | BS ISO 10428 - PETROLEUM AND NATURAL GAS INDUSTRIES DOWNHOLE EQUIPMENT - DOWNHOLE EQUIPMENT - SUCKER RODS, COUPLINGS AND ANCILLARY EQUIPMENT |
| ASTM D 1474 : 1998 : R2002 | Standard Test Methods for Indentation Hardness of Organic Coatings |
| ASTM F 364 : 1996 : R2014 | Standard Specification for Molybdenum Flattened Wire for Electron Tubes |
| SAE AMS 2762 : 2018 | CARBURIZING - CARBON AND LOW-ALLOY STEEL PARTS |
| SAE AMS 5960 : 2013 | NICKEL ALLOY, CORROSION AND HEAT-RESISTANT SHEET, STRIP, AND FOIL, NI - 18CR - 2.8MO - 5.5CB(NB) - 0.70TI - 1.50AL - 10FE - 9CO - 1W, VACUUM INDUCTION MELTED AND CONSUMABLE ELECTRODE REMELTED, SOLUTION HEAT TREATED |
| SAE AMS 6356 : 2015 | STEEL, SHEET, STRIP, AND PLATE, 0.95CR - 0.20MO - (0.30 - 0.35C) (4132) |
| MIL-DTL-32480 Base Document:2014 | Adapter, Hydraulic and Pneumatic, Flareless Tube Fitting to ORFS Connectors, 1500 to 3000 PSI and Minus 65 Degrees Fahrenheit to Plus 250 Degrees Fahrenheit, General Specification for |
| SAE AMS 6350 : 2015 | STEEL SHEET, STRIP, AND PLATE, 0.95CR - 0.20MO (0.28 - 0.33C) (SAE 4130) |
| ASTM C 849 : 1988 : R2016 | Standard Test Method for Knoop Indentation Hardness of Ceramic Whitewares |
| SAE AMS 6370 : 2016 | STEEL, BARS, FORGINGS, AND RINGS, 0.95CR - 0.20MO (0.28 - 0.33C) (SAE 4130) |
| SAE AMS 7851 : 2017 | COLUMBIUM (NIOBIUM) ALLOY FOIL, SHEET, STRIP, AND PLATE, 10W - 2.5ZR, RECRYSTALLIZED |
| BS EN ISO 17945:2015 | Petroleum, petrochemical and natural gas industries. Metallic materials resistant to sulfide stress cracking in corrosive petroleum refining environments |
| SAE AMS 6330 : 2017 | STEEL BARS, FORGINGS, AND TUBING, 0.65CR - 1.25NI (0.33 - 0.38C) |
| SAE AMS 7849E : 2015(R2018) | TANTALUM SHEET, STRIP, AND PLATE, ANNEALED |
| MIL-H-6875 Revision H:1989 | HEAT TREATMENT OF STEEL RAW MATERIALS |
| SAE MAM 5914 : 2003 | NICKEL ALLOY, CORROSION AND HEAT RESISTANT, SHEET, STRIP, AND FOIL 52.5NI - 19CR - 3.0MO - 5.0CB - 0.90TI - 0.50AL - 18FE CONSUMABLE ELECTRODE OR VACUUM INDUCTION MELTED PRECISION COLD ROLLED, SOLUTION HEAT TREATED |
| 13/30261096 DC : 0 | BS EN ISO 17945 - MATERIALS RESISTANT TO SULFIDE STRESS CRACKING IN CORROSIVE PETROLEUM REFINING ENVIRONMENTS |
| MIL-DTL-32372 Revision A:2016 | Fitting, Adapter, Hydraulic and Pneumatic, NPTF to ORFS Connectors, 1500 to 3000 PSI and -65°F to 250°F |
| SAE AMS 5902 : 2008 | STEEL, CORROSION-RESISTANT, SHEET AND STRIP, 18CR - 8NI (SAE 30301), COLD ROLLED, 3/4 HARD, 175 KSI (1207 MPA) TENSILE STRENGTH |
| SAE AMS 6527 : 2018 | STEEL, BARS AND FORGINGS, 2.0CR - 10NI - 14CO - 1.0MO (0.15 - 0.19C), VACUUM MELTED, NORMALIZED AND OVERAGED |
| SAE AMS 5223 : 2012 | IRON-NICKEL ALLOY, STRIP, 49Fe 5.3Cr 42Ni 2.5Ti 0.55Al, SOLUTION HEAT TREATED, COLD ROLLED, 10% REDUCTION |
| ASTM B 596 : 1989 : R2006 | Standard Specification for Gold-Copper Alloy Electrical Contact Material |
| SAE AMS6328N : 2017 | STEEL, BARS, FORGINGS, AND TUBING, 0.50CR - 0.55NI - 0.25MO (0.48 TO 0.53C) (SAE 8750) |
| MIL-PRF-32577 Base Document:2017 | COATING SYSTEM, NONSKID, METALLIC THERMAL SPRAY APPLICATION |
| ASTM E 1268 : 2001 : R2007 | Standard Practice for Assessing the Degree of Banding or Orientation of Microstructures |
| SAE AMS 6434 : 2016 | STEEL, SHEET, STRIP, AND PLATE, 0.78CR - 1.8NI - 0.35MO - 0.20V (0.33 - 0.38C) (4335 MOD) |
| SAE AMS 6433 : 2015 | STEEL, SHEET, STRIP, AND PLATE 0.75MN - 0.78CR - 1.8NI - 0.35MO - 0.20V (0.33 - 0.38C) (4335 MOD) |
| ABMA 10A : 2001 : R2008 | METAL BALLS FOR UNGROUND BEARINGS AND OTHER USES |
| API 5ST:2010 | SPECIFICATION FOR COILED TUBING |
| SAE AMS 4990 : 2015 | TITANIUM ALLOY SHEET, STRIP, AND PLATE, 6AL - 6V - 2SN, SOLUTION HEAT TREATED AND AGED |
| API 11AX RUSSIAN : 13ED 2015 | SPECIFICATION FOR SUBSURFACE SUCKER ROD PUMP ASSEMBLIES, COMPONENTS, AND FITTINGS, THIRTEENTH EDITION |
| SAE AMS 6257 : 2016 | STEEL BARS, FORGINGS, AND TUBING, 1.6SI - 0.82CR - 1.8NI - 0.40MO - 0.08V (0.40 - 0.44C), CONSUMABLE ELECTRODE VACUUM REMELTED, NORMALIZED AND TEMPERED |
| MIL-HDBK-1886 Base Document:1998 | TUNGSTEN CARBIDE-COBALT COATING, DETONATION PROCESS FOR |
| MIL-S-8844 Revision D:1987 | STEEL BAR, REFORGING STOCK AND MECHANICAL TUBING LOW ALLOY PREMIUM QUALITY |
| API 5L CHINESE : 2012 | SPECIFICATION FOR LINE PIPE |
| SAE AMS 2368 : 2017 | SAMPLING AND TESTING OF WROUGHT TITANIUM RAW MATERIAL EXCEPT FORGINGS AND FORGING STOCK |
| CSA Z662.1 : 2013 | COMMENTARY ON CSA Z662-07, OIL AND GAS PIPELINE SYSTEMS |
| SAE AMS 6282 : 2015 | STEEL TUBING, MECHANICAL, 0.50CR - 0.55NI - 0.25MO (0.33 - 0.38C) (SAE 8735) |
| SAE AMS 7852 : 2017 | COLUMBIUM (NIOBIUM) ALLOY SHEET, STRIP, AND PLATE, 10HF - 1.0TI |
| API 11B : 2010 | SPECIFICATION FOR SUCKER RODS, POLISHED RODS AND LINERS, COUPLINGS, SINKER BARS, POLISHED ROD CLAMPS, STUFFING BOXES, AND PUMPING TEES |
| SAE AMS 6302K : 2017 | LOW-ALLOY STEEL, HEAT-RESISTANT, BARS, FORGINGS, AND TUBING, 0.65SI - 1.25CR - 0.50MO - 0.25V (0.28 - 0.33C) |
| SAE AMS 4987 : 2015 | TITANIUM ALLOY, FORGINGS, 10V - 2FE - 3AI, CONSUMABLE ELECTRODE MELTED, SINGLE-STEP SOLUTION HEAT TREATED AND OVERAGED, 140 KSI (965 MPA) TENSILE STRENGTH |
| SAE AMS 4907 : 2013 | TITANIUM ALLOY, SHEET, STRIP, AND PLATE, 6.0AL - 4.0V, EXTRA LOW INTERSTITIAL, ANNEALED |
| SAE AMS 5903 : 2006 | STEEL, CORROSION-RESISTANT, SHEET, STRIP, AND PLATE, 18CR - 9.0NI (SAE 30302), COLD ROLLED, 1/4 HARD, 125 KSI (862 MPA) TENSILE STRENGTH |
| SAE AMS 6528 : 2017 | STEEL, BARS, 0.95CR - 0.20MO (0.28 - 0.33C) (SAE 4130), SPECIAL AIRCRAFT QUALITY CLEANLINESS, NORMALIZED |
| AWS B4.0M : 2000 | STANDARD METHODS FOR MECHANICAL TESTING OF WELDS |
| AWS WHB.3.9 : 2007 | WELDING PROCESSES - PART 2: WELDING HANDBOOK, 9TH EDITION, VOL. 3 |
| AWS B4.0:2016 | STANDARD METHODS FOR MECHANICAL TESTING OF WELDS |
| AWS D1.5M/D1.5 : 2015 | BRIDGE WELDING CODE |
| SAE AMS 6949 : 2016 | TITANIUM ALLOY, SHEET AND STRIP, 4AL - 2.5V - 1.5FE, ELECTRON BEAM SINGLE MELTED. ANNEALED |
| SAE AMS 5631 : 2018 | STEEL, CORROSION-RESISTANT, BARS AND FORGINGS, 17CR (0.60 - 0.75C) (440A) |
| SAE AMS 6946 : 2014 | TITANIUM ALLOY, SHEET, STRIP, AND PLATE 4AL - 2.5V - 1.5FE, ANNEALED |
| SAE AMS 2355 : 2017 | QUALITY ASSURANCE, SAMPLING AND TESTING, ALUMINUM ALLOYS AND MAGNESIUM ALLOY, WROUGHT PRODUCTS (EXCEPT FORGING STOCK), AND ROLLED, FORGED, OR FLASH WELDED RINGS |
| EN ISO 3183:2012/A1:2018 | PETROLEUM AND NATURAL GAS INDUSTRIES - STEEL PIPE FOR PIPELINE TRANSPORTATION SYSTEMS (ISO 3183:2012) |
| SAE AMS 5910 : 2012 | STEEL, CORROSION-RESISTANT, SHEET, STRIP, AND PLATE, 19CR - 9.2NI (SAE 30304) COLD ROLLED, 125 KSI (862 MPA) TENSILE STRENGTH |
| SAE AMS 2585A : 2013 | SHOT PEENING MEDIA, ULTRASONICALLY ACTIVATED |
| ASTM B 477 : 1997 : R2002 | Standard Specification for Gold-Silver-Nickel Electrical Contact Alloy |
| SAE AMS 4903 : 2015 | TITANIUM ALLOY SHEET, STRIP, AND PLATE, 6AL - 4V, SOLUTION HEAT TREATED |
| ASTM F 3213 : 2017 | Standard for Additive Manufacturing – Finished Part Properties – Standard Specification for Cobalt-28 Chromium-6 Molybdenum via Powder Bed Fusion |
| ASTM C 522 : 2003 | Standard Test Method for Airflow Resistance of Acoustical Materials |
| ASTM D 1474 : 1998 | Standard Test Methods for Indentation Hardness of Organic Coatings |
| SAE J 441 : 2013 | Cut Wire Shot |
| ASTM C 849 : 1988 : R1999 | Standard Test Method for Knoop Indentation Hardness of Ceramic Whitewares |
| ASTM C 730 : 1998 : R2013 | Standard Test Method for<brk type="line"/> Knoop Indentation Hardness of Glass |
| ASTM C 522 : 2003 : R2009 : EDT 1 | Standard Test Method for Airflow Resistance of Acoustical Materials |
| ASTM E 1268 : 2001 : R2016 | Standard Practice for Assessing the Degree of Banding or Orientation of Microstructures |
| ASTM C 730 : 1998 : R2008 | Standard Test Method for Knoop Indentation Hardness of Glass |
| ASTM E 2546 : 2015 : REDLINE | Standard Practice for Instrumented Indentation Testing |
| ASTM B 832 : 1993 : R2003 | Standard Guide for Electroforming with Nickel and Copper |
| ASTM B 596 : 1989 : R2017 | Standard Specification for Gold-Copper Alloy Electrical Contact Material |
| ASTM F 2215 : 2015 : REDLINE | Standard Specification for Balls, Bearings, Ferrous and Nonferrous for Use in Bearings, Valves, and Bearing Applications |
| ASTM B 578 : 1987 : R1999 | Standard Test Method for Microhardness of Electroplated Coatings |
| NFPA 1901:2016 | AUTOMOTIVE FIRE APPARATUS |
| DIN EN ISO 15156-2:2015-12 | PETROLEUM AND NATURAL GAS INDUSTRIES - MATERIALS FOR USE IN H[2]S-CONTAINING ENVIRONMENTS IN OIL AND GAS PRODUCTION - PART 2: CRACKING-RESISTANT CARBON AND LOW-ALLOY STEELS, AND THE USE OF CAST IRONS (ISO 15156-2:2015) |
| BS EN ISO 13628-2:2006 | Petroleum and natural gas industries. Design and operation of subsea production systems Unbonded flexible pipe systems for subsea and marine applications |
| MIL-PRF-26542-3 Revision E:2012 | MICROPHONE ASSEMBLY, M100/AIC |
| MIL-DTL-12133 Revision E:2015 | WASHER, SPRING TENSION, GENERAL SPECIFICATION FOR |
| SAE AMS 6558 : 2013 | STEEL, BARS, WIRE, AND FORGINGS 10.5MO - 6W - 3.75CR - 2V (1.25 - 1.40C) POWDER METALLURGY PRODUCT HOT ISOSTATICALLY PRESSED |
| SAE AMS 5923 : 2013 | STEEL, CORROSION-RESISTANT, BARS, WIRE, AND FORGINGS,17CR - 0.52MO (0.95 - 1.20C) (SAE 51440C), FOR BEARING APPLICATIONS |
| SAE AMS 5544 : 2014 | NICKEL ALLOY, CORROSION AND HEAT-RESISTANT, SHEET, STRIP, AND PLATE, 57NI - 19.5CR - 13.5CO - 4.2MO - 3.0TI - 1.4AL - 0.05ZR - 0.006B, CONSUMABLE ELECTRODE OR VACUUM INDUCTION MELTED, ANNEALED |
| SAE AMS 4916L : 2017 | TITANIUM ALLOY SHEET, STRIP, AND PLATE 8AL - 1MO - 1V DUPLEX ANNEALED |
| SAE AMS 5914 : 2012 | NICKEL ALLOY, CORROSION AND HEAT RESISTANT, SHEET, STRIP, AND FOIL 52.5NI - 19CR - 3.0MO - 5.0CB - 0.90TI - 0.50AL - 18FE, CONSUMABLE ELECTRODE OR VACUUM INDUCTION MELTED PRECISION COLD ROLLED, SOLUTION HEAT TREATED |
| API SPEC 20E : 2017 | ALLOY AND CARBON STEEL BOLTING FOR USE IN THE PETROLEUM AND NATURAL GAS INDUSTRIES |
| MIL-STD-1876 Revision A:1991 | NITRIDING, GASEOUS ATMOSPHERE PROCESSING FOR |
| SAE AMS 4909 : 2016 | TITANIUM ALLOY, SHEET, STRIP, AND PLATE 5AL - 2.5SN, EXTRA LOW INTERSTITIAL ANNEALED |
| SAE AMS 6280 : 2017 | STEEL BARS, FORGINGS, AND RINGS, 0.50CR - 0.55NI - 0.20MO (0.28 - 0.33C) (SAE 8630) |
| SAE AMS 6412 : 2015 | STEEL, BARS AND FORGINGS 0.80CR - 1.8NI - 0.25MO (0.35 - 0.40C) (4337) |
| SAE AMS 6378 : 2014 | STEEL BARS, 1.0CR - 0.20MO - 0.45SE (0.39 - 0.48C) (4142H MODIFIED), DIE-DRAWN, 130 KSI (896 MPA) YIELD STRENGTH, FREE MACHINING |
| SAE AMS 5596 : 2017 | NICKEL ALLOY, CORROSION AND HEAT-RESISTANT, SHEET, STRIP, FOIL AND PLATE, 52.5NI - 19CR - 3.0MO - 5.1CB (NB) - 0.90TI - 0.50AL - 18FE, CONSUMABLE ELECTRODE REMELTED OR VACUUM INDUCTION MELTED, 1775 DEGREES F (968 DEGREES C) SOLUTION HEAT TREATED |
| SAE AMS 6475 : 2013 | STEEL, NITRIDING, BARS, FORGINGS, AND TUBING, 1.1CR - 3.5NI - 0.25MO - 1.2AL (0.21 - 0.26C) |
| SAE AMS 5621 : 2015 | STEEL, CORROSION RESISTANT, BARS, WIRE, AND FORGINGS, 13CR (0.30-0.40C) (51420), ANNEALED |
| SAE AMS 6953 : 2018 | TITANIUM ALLOY SHEET, 6AL - 4SN - 3NB - 0.5MO - 0.3SI, DUPLEX ANNEALED |
| SAE AMS 6413 : 2016 | STEEL, MECHANICAL TUBING 0.80CR - 1.8NI - 0.25MO (0.35 - 0.40C) (4337) |
| ASTM C 1327 : 2015 : REDLINE | TEST METHOD FOR VICKERS INDENTATION HARDNESS OF ADVANCED CERAMICS |
| MIL-T-55155 Revision C:1993 | TERMINALS, FEEDTHRU (INSULATED) AND TERMINALS, STUD (INSULATED AND NONINSULATED), GENERAL SPECIFICATION FOR |
| ASTM A 1086 : 2013 | Standard Specification for Thin-Gauge Nonoriented Electrical Steel Fully Processed Types |
| SAE AMS 2774 : 2016 | HEAT TREATMENT, WROUGHT NICKEL ALLOY AND COBALT ALLOY PARTS |
| SAE AMS 6352 : 2013 | STEEL SHEET, STRIP, AND PLATE, 0.95CR - 0.20MO (0.33 - 0.38C) (SAE 4135) |
| ASTM E 1077 : 2014 : REDLINE | Standard Test Methods for Estimating the Depth of Decarburization of Steel Specimens |
| API 64 : 2017-08 | DIVERTER EQUIPMENT SYSTEMS |
| ASTM B 277 : 1995 | Standard Test Method for Hardness of Electrical Contact Materials |
| W59-13 | Welded steel construction (metal arc welding) |
| SAE AMS 2404 : 2018 | PLATING, ELECTROLESS NICKEL |
| ASTM A 826/A826M : 1995 | Standard Specification for Seamless Austenitic and Martensitic Stainless Steel Duct Tubes for Liquid Metal-Cooled Reactor Core Components |
| FF-O-601 Revision F:1990 | OPENERS, CAN, HAND AND MOUNTED |
| API 5L RUSSIAN : 2012 | SPECIFICATION FOR LINE PIPE |
| SAE AMS 6455 : 2016 | STEEL, SHEET, STRIP, AND PLATE, 0.95CR - 0.22V (0.48 - 0.53C) (SAE 6150) |
| DOD-STD-35-36 Revision B:1979 | AUTOMATED ENGINEERING DOCUMENT PREPARATION SYSTEM SEALS, GASKETS AND PACKING |
| BS ISO 4498:2005 | Sintered metal materials, excluding hardmetals. Determination of apparent hardness and microhardness |
| API STD 1104 SPANISH : 2013 | WELDING OF PIPELINES AND RELATED FACILITIES |
| I.S. EN ISO 3183:2012 | PETROLEUM AND NATURAL GAS INDUSTRIES - STEEL PIPE FOR PIPELINE TRANSPORTATION SYSTEMS (ISO 3183:2012) |
| ABMA 10A : 2001 : R2015 | METAL BALLS FOR UNGROUND BEARINGS AND OTHER USES |
| SAE AMS 2759/7 : 2010 | CARBURIZING AND HEAT TREATMENT OF CARBURIZING GRADE STEEL PARTS |
| SAE AMS 5085 : 2017 | STEEL SHEET, STRIP, AND PLATE, 0.48 - 0.55C (SAE 1050) |
| SAE AMS 6551 : 2013 | STEEL BARS, FORGINGS AND TUBING 1.75CR - 4.0NI - 0.5MO - (0.35 - 0.40C) PREMIUM AIRCRAFT QUALITY CONSUMABLE ELECTRODE VACUUM REMELTED |
| MIL-DTL-32464 Revision A:2017 | FITTINGS, ADAPTER, HYDRAULIC AND PNEUMATIC, 37 DEGREES SPHERICAL TO ANPT CONNECTORS, 1500 TO 3000 PSI, GENERAL SPECIFICATION FOR |
| ASTM B 476 : 2001 : R2017 | Standard Specification for General Requirements for Wrought Precious Metal Electrical Contact Materials |
| API 5C7:1996 | RECOMMENDED PRACTICE FOR COILED TUBING OPERATIONS IN OIL AND GAS WELL SERVICES |
| NACE TM 01 77 : 2016 | LABORATORY TESTING OF METALS FOR RESISTANCE TO SULFIDE STRESS CRACKING AND STRESS CORROSION CRACKING IN H[2]S ENVIRONMENTS |
| DOD-F-24669-3 Base Document:1986 | FORGINGS AND FORGING STOCK, STEEL BARS AND BILLETS FOR NITRIDING (METRIC) |
| API SPEC 16F : 2017 | SPECIFICATION FOR MARINE DRILLING RISER EQUIPMENT |
| SAE AMS 3880 : 2016 | CRYSTALLIZED GLASS CERAMIC |
| MIL-DTL-32371 Base Document:2012 | Fittings, Adapter, Hydraulic and Pneumatic, Spherical to ORFS Connectors, 1500 to 3000 PSI, General Specification for |
| SAE AMS 6427 : 2014 | STEEL BARS, FORGINGS, AND TUBING, 0.88CR - 1.8NI - 0.42MO - 0.08V (0.25 - 0.33C) (4330 MOD) |
| SAE AMS 6385 : 2015 | STEEL SHEET, STRIP, AND PLATE, LOW ALLOY, HEAT-RESISTANT, 0.65SI - 1.25CR - 0.50MO - 0.25V (0.27 - 0.33C) |
| SAE AMS 6454 : 2011 | STEEL, SHEET, STRIP, AND PLATE, 1.8NI - 0.80CR - 0.25MO (0.38 - 0.43C) (SAE 4340) VACUUM CONSUMABLE ELECTRODE REMELTED |
| ASTM C 730 : 1998 : R2003 | Standard Test Method for Knoop Indentation Hardness of Glass |
| ASTM F 3042 : 2013 | Standard Specification for Nonferrous Hex Socket, Slotted Headless, and Square Head Set Screws |
| ASTM B 540 : 1997 : R2012 | Standard Specification for Palladium Electrical Contact Alloy |
| SAE AMS 6447 : 2016 | STEEL, BARS, FORGINGS, AND TUBING, 1.4CR (0.93-1.05C) (SAE 52100), ELECTROSLAG REMELTED |
| ASTM B 541 : 2001 : R2018 | Standard Specification for Gold Electrical Contact Alloy |
| SAE AMS 6431 : 2017 | STEEL, BARS, FORGINGS, AND TUBING, 1.05CR - 0.55NI - 1.0MO - 0.11V (0.45 - 0.50C) (D6AC), VACUUM CONSUMABLE ELECTRODE REMELTED |
| CSA Z662 PACKAGE : 2011 | CONSISTS OF Z662-11, OIL AND GAS PIPELINE SYSTEMS AND Z662.1-11, COMMENTARY ON CSA Z662-11, OIL AND GAS PIPELINE SYSTEMS |
| SAE AMS 6479 : 2015 | STEEL, BARS, FORGINGS, AND TUBING 1.45CR (0.93-1.05C) (SAE 52100) SPECIAL AIRCRAFT-QUALITY CLEANLINESS |
| ASTM B 563 : 2001 | Standard Specification for Palladium-Silver-Copper Electrical Contact Alloy |
| ASTM C 849 : 1988 : R2011 | Standard Test Method for Knoop Indentation Hardness of Ceramic Whitewares |
| ASTM B 563 : 2001 : R2011 | Standard Specification for Palladium-Silver-Copper Electrical Contact Alloy |
| SAE AMS 5905 : 2012 | STEEL, CORROSION-RESISTANT, SHEET AND STRIP, 18CR - 9.0NI (SAE 30302), COLD ROLLED, 3/4 HARD, 175 KSI (1207 MPA) TENSILE STRENGTH |
| SAE AMS 5926 : 2016 | STEEL, CORROSION-RESISTANT, BARS, WIRE, TUBING, AND FORGINGS 15.5CR - 1.5SI - 0.3MO - 0.1N (0.45 - 0.60C) FOR BEARING APPLICATIONS |
| SAE J 827 : 2013 | HIGH-CARBON CAST-STEEL-SHOT |
| ASTM F 2511 : 2005 | Standard Specification for Rollers, Bearing, Needle, Ferrous, Solid |
| SAE MAM 4911 : 1994 | TITANIUM ALLOY, SHEET, STRIP, AND PLATE, 6AL - 4V, ANNEALED |
| SAE AMS 2755 : 2015 | NITRIDING, MOLTEN SALT BATH |
| SAE AMS 6300 : 2015 | STEEL BARS AND FORGINGS, 0.25MO (0.35 - 0.40C) (SAE 4037) |
| SAE AMS 6470 : 2014 | STEEL, NITRIDING, BARS, FORGINGS, AND TUBING 1.6CR - 0.35MO - 1.13AL (0.38 - 0.43C) (135 MOD) |
| SAE AMS 5913 : 2014 | STEEL, CORROSION-RESISTANT, SHEET AND STRIP, 19CR - 9.2NI (SAE 30304), COLD ROLLED, FULL HARD, 185 KSI (1276 MPA) TENSILE STRENGTH |
| SAE AMS 6359 : 2015 | STEEL, SHEET, STRIP, AND PLATE 0.80CR - 1.8NI - 0.25MO (0.38 - 0.43C) (SAE 4340) |
| NACE TM 01 03 : 2003 | LABORATORY TEST PROCEDURES FOR EVALUATION OF SOHIC RESISTANCE OF PLATE STEELS USED IN WET H[2]S SERVICE |
| SAE AMS 6494 : 2016 | STEEL BARS, FORGINGS, AND TUBING, 1.0CR - 2.50NI - 2.0MO - 1.10SI (0.10 - 0.20C) AIRCRAFT-QUALITY |
| BS EN ISO 3183 : 2012 | PETROLEUM AND NATURAL GAS INDUSTRIES - STEEL PIPE FOR PIPELINE TRANSPORTATION SYSTEMS |
| SAE AMS 6360 : 2013 | STEEL TUBING, SEAMLESS, 0.95CR - 0.20MO (0.28 - 0.33C) (SAE 4130), NORMALIZED OR STRESS RELIEVED |
| SAE AMS 5618 : 2017 | STEEL, CORROSION-RESISTANT, BARS, WIRE, AND FORGINGS, 17CR - 0.52MO (0.95 - 1.20C) (440C), CONSUMABLE ELECTRODE VACUUM MELTED |
| ASTM B 477 : 1997 : R2017 | Standard Specification for Gold-Silver-Nickel Electrical Contact Alloy |
| SAE AMS 6417 : 2015 | STEEL, BARS, FORGINGS, AND TUBING, 1.6SI - 0.82CR - 1.8NI - 0.40MO - 0.08V (0.38 - 0.43C), CONSUMABLE ELECTRODE VACUUM REMELTED |
| OIML G 5 : 1989 | HARDNESS STANDARD EQUIPMENT |
| SAE AMS 7857 : 2017 | COLUMBIUM (NIOBIUM) ALLOY BARS, RODS, AND EXTRUSIONS, 10HF - 1.0TI, RECRYSTALLIZATION ANNEALED |
| ASTM F 3056 : 2014 | Standard Specification for Additive Manufacturing Nickel Alloy (UNS N06625) with Powder Bed Fusion |
| ASTM F 2924 : 2014 : REDLINE | Standard Specification for Additive Manufacturing Titanium-6 Aluminum-4 Vanadium with Powder Bed Fusion |
| ASTM F 912 : 2011 : R2017 | Standard Specification for Alloy Steel Socket Set Screws |
| ASTM A 1038 : 2017 : REDLINE | Standard Test Method for Portable Hardness Testing by the Ultrasonic Contact Impedance Method |
| ASTM B 388 : 2006 | Standard Specification for Thermostat Metal Sheet and Strip |
| ASTM F 3056 : 2014 : EDT 1 | Standard Specification for Additive Manufacturing Nickel Alloy (UNS N06625) with Powder Bed Fusion |
| SAE AMS 6340 : 2014 | STEEL BARS, FORGINGS, AND TUBING 0.88CR - 1.8NI - 0.42MO - 0.08V (0.28 - 0.33C) (4330 MOD) CONSUMABLE ELECTRODE VACUUM REMELTED |
| SAE AMS 2759 : 2014 | HEAT TREATMENT OF STEEL PARTS, GENERAL REQUIREMENTS |
| SAE AMS 6348 : 2013 | STEEL, BARS, 0.95CR - 0.20MO (0.28 TO 0.33C) (SAE 4130), NORMALIZED |
| ASTM C 849 : 1988 : R2006 | Standard Test Method for Knoop Indentation Hardness of Ceramic Whitewares |
| ASTM F 879 : 2015 : REDLINE | Standard Specification for Stainless Steel Socket Button and Flat Countersunk Head Cap Screws |
| ASTM B 69 : 2016 : REDLINE | Standard Specification for Rolled Zinc |
| ASTM D 1474 : 1998 : R2008 | Standard Test Methods for Indentation Hardness of Organic Coatings |
| ASTM B 477 : 1997 : R2008 | Standard Specification for Gold-Silver-Nickel Electrical Contact Alloy |
| ASTM B 540 : 1997 : R2017 | Standard Specification for Palladium Electrical Contact Alloy |
| ASTM F 1459 : 2006 | Standard Test Method for Determination of the Susceptibility of Metallic Materials to Hydrogen Gas Embrittlement (HGE) |
| ASTM F 3055 : 2014 | Standard Specification for Additive Manufacturing Nickel Alloy (UNS N07718) with Powder Bed Fusion |
| ASTM F 3055 : 2014 : EDT 1 | Standard Specification for Additive Manufacturing Nickel Alloy (UNS N07718) with Powder Bed Fusion |
| ASTM B 541 : 2001 | Standard Specification for Gold Electrical Contact Alloy |
| ASTM B 388 : 2006 : R2012 | Standard Specification for Thermostat Metal Sheet and Strip |
| DIN EN ISO 4498:2010-11 | Sintered metal materials, excluding hardmetals - Determination of apparent hardness and microhardness (ISO 4498:2010) |
| I.S. EN ISO 13628-2:2006 | PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 2: UNBONDED FLEXIBLE PIPE SYSTEMS FOR SUBSEA AND MARINE APPLICATIONS |
| I.S. EN ISO 15156-2:2015&LC:2015 | PETROLEUM AND NATURAL GAS INDUSTRIES - MATERIALS FOR USE IN H[2]S-CONTAINING ENVIRONMENTS IN OIL AND GAS PRODUCTION - PART 2: CRACKING-RESISTANT CARBON AND LOW-ALLOY STEELS, AND THE USE OF CAST IRONS (ISO 15156-2:2015) |
| EN ISO 15156-2:2015 | Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - Part 2: Cracking-resistant carbon and low alloy steels, and the use of cast irons (ISO 15156-2:2015) |
| EN ISO 15156-3:2015 | Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys (ISO 15156-3:2015) |
| I.S. EN ISO 4498:2010 | SINTERED METAL MATERIALS, EXCLUDING HARDMETALS - DETERMINATION OF APPARENT HARDNESS AND MICROHARDNESS |
| ASME PCC 2 : 2015 | REPAIR OF PRESSURE EQUIPMENT AND PIPING |
| SAE AMS 4940 : 2017 | TITANIUM SHEET, STRIP, AND PLATE COMMERCIALLY PURE ANNEALED, 25.0 KSI (172 MPA) YIELD STRENGTH |
| MIL-STD-3049 Base Document:2013 | MATERIALS DEPOSITION, DDM: DIRECT DEPOSITION OF METAL FOR REMANUFACTURE, RESTORATION AND RECOATING |
| SAE AMS 5932 : 2012 | STEEL, CORROSION AND HEAT-RESISTANT, BARS, FORGINGS AND TUBING 14.5CR - 2.3NI - 12.5CO - 4.0MO - 0.60V - 0.03CB(NB), CARBURIZING, PREMIUM AIRCRAFT-QUALITY, DOUBLE VACUUM MELTED |
| ASTM B 277 : 1995 : R2006 | Standard Test Method for Hardness of Electrical Contact Materials |
| SAE AMS 5911 : 2014 | STEEL, CORROSION-RESISTANT, SHEET AND STRIP, 19CR - 9.2NI (SAE 30304) COLD ROLLED, 1/2 HARD, 150 KSI (1034 MPA) TENSILE STRENGTH |
| I.S. EN ISO 13628-5:2009 | PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 5: SUBSEA UMBILICALS |
| MIL-DTL-18866 Revision J:2015 | Fittings, Hydraulic Tube, Flared, 37 Degree and Flareless, General Specification for |
| ASTM C 522 : 2003 : R2016 | Standard Test Method for Airflow Resistance of Acoustical Materials |
| BS 3531-8:1982 | Surgical implants Specification for ceramic materials based on alumina |
| I.S. EN 843-4:2005 | ADVANCED TECHNICAL CERAMICS - MECHANICAL PROPERTIES OF MONOLITHIC CERAMICS AT ROOM TEMPERATURE - PART 4: VICKERS, KNOOP AND ROCKWELL SUPERFICIAL HARDNESS |
| SAE AMS 6278 : 2016 | STEEL, BARS, FORGINGS, AND TUBING, 4.1CR - 3.4NI - 4.2MO - 1.2V (0.11 - 0.15C), PREMIUM AIRCRAFT-QUALITY FOR BEARING APPLICATIONS, DOUBLE VACUUM MELTED |
| ASTM B 563 : 2001 : R2017 | Standard Specification for Palladium-Silver-Copper Electrical Contact Alloy |
| SAE AMS 6327L : 2017 | STEEL BARS AND FORGINGS, 0.50CR - 0.55NI - 0.25MO (0.38 - 0.43C) (SAE 8740), HEAT TREATED, 125 KSI (862 MPA) TENSILE STRENGTH (COMPOSITION SIMILAR TO UNS G87400) |
| SAE AMS 5225 : 2014 | IRON-NICKEL ALLOY, STRIP, 49FE - 5.3CR - 42NI - 2.5TI - 0.55AL, SOLUTION HEAT TREATED, COLD ROLLED, 50% REDUCTION |
| SAE AMS 4910 : 2017 | TITANIUM ALLOY, SHEET, STRIP, AND PLATE 5AL - 2.5SN ANNEALED |
| ASTM F 364 : 1996 : R2009 | Standard Specification for Molybdenum Flattened Wire for Electron Tubes |
| SAE AS 7108 : 2009 | NADCAP AUDIT CRITERIA FOR CHEMICAL PROCESSING |
| SAE AMS 2437 : 2012 | COATING, PLASMA SPRAY DEPOSITION |
| ASTM C 1326 : 2013 | Standard Test Method for Knoop Indentation Hardness of Advanced Ceramics |
| SAE AMS 2759/13 : 2018 | GASEOUS NITROCARBURIZING |
| SAE AIR 4777 : 2013(R 2018) | NONDESTRUCTIVE INSPECTION (NDI) METHODS USED DURING PRODUCTION AND OPERATION OF AIRCRAFT WHEELS AND BRAKES |
| SAE AMS 6304 : 2016 | LOW-ALLOY STEEL, HEAT-RESISTANT, BARS, FORGINGS, AND TUBING, 0.95CR - 0.55MO - 0.30V (0.40 - 0.50C) |
| SAE AMS 6409E : 2016 | STEEL, BARS, FORGINGS, AND TUBING 0.80CR - 1.8NI - 0.25MO (0.38 - 0.43C) (SAE 4340) SPECIAL AIRCRAFT QUALITY CLEANLINESS, NORMALIZED AND TEMPERED |
| ASTM B 578 : 1987 : R2015 | Standard Test Method for Microhardness of Electroplated Coatings |
| SAE AMS 6945 : 2014 | TITANIUM ALLOY, SINGLE MELT, SHEET, STRIP, AND PLATE 6AL - 4V ANNEALED |
| SAE AMS 6320 : 2017 | STEEL BARS, FORGINGS, AND RINGS 0.50CR - 0.55NI - 0.25MO (0.33 - 0.38C) (8735) |
| SAE ARP 4715A : 2011(S2018) | INDUCTION HARDENING OF STEEL COMPONENTS |
| NACE RP 04 72 : 2005 | METHODS AND CONTROLS TO PREVENT IN-SERVICE ENVIRONMENTAL CRACKING OF CARBON STEEL WELDMENTS IN CORROSIVE PETROLEUM REFINING ENVIRONMENTS |
| AGMA 2004 : C | GEAR MATERIALS, HEAT TREATMENT AND PROCESSING MANUAL |
| DIN EN ISO 17945 E : 2015 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - METALLIC MATERIALS RESISTANT TO SULFIDE STRESS CRACKING IN CORROSIVE PETROLEUM REFINING ENVIRONMENTS (ISO 17945:2015) |
| SAE AMS 2454 : 2012 | PLATING, ELECTROLESS NICKEL, CODEPOSITED WITH POLYTETRAFLUOROETHYLENE (PTFE) |
| 04/301931 DC : DRAFT JAN 2004 | ISO 13628-2 - PETROLEUM AND NATURAL GAS INDUSTRIES DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 2: UNBONDED FLEXIBLE PIPE SYSTEMS FOR SUBSEA AND MARINE APPLICATIONS |
| MIL-DTL-32460 Revision A:2017 | ADAPTER, HYDRAULIC AND PNEUMATIC, 37 DEGREES FLARE TUBE FITTING TO ORFS CONNECTORS, 1500 TO 3000 PSI AND -65 DEGREES F TO 250 DEGREES F, GENERAL SPECIFICATION FOR |
| SAE AMS 4919 : 2014 | TITANIUM ALLOY SHEET, STRIP, AND PLATE 6AL - 2SN - 4ZR - 2MO - 0.08SI DUPLEX ANNEALED |
| 07/30127452 DC : DRAFT AUG 2007 | BS ISO 13628-5 - PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 5: SUBSEA UMBILICALS |
| GGG-D-751 Revision D:1989 | DRILLS, TWIST (TAPER-SQUARE, STRAIGHT, AND TAPER-ROUND SHANKS) |
| SAE AMS 5907 : 2012 | STEEL, CORROSION AND HEAT-RESISTANT, SHEET, STRIP, AND PLATE, 17CR - 12NI - 2.5MO (SAE 30316), COLD ROLLED, 1/4 HARD, 125 KSI (862 MPA) TENSILE STRENGTH |
| Z245.15-17 | Steel valves |
| MIL-P-85856 Base Document:1988 | POWDER MATERIALS FOR FLAME AND PLASMA SPRAYED COATINGS GENERAL SPECIFICATION FOR |
| API SPEC 17E : 2017 | SPECIFICATION FOR SUBSEA UMBILICALS |
| MIL-DTL-32502 Base Document:2014 | Coating, Cobalt-Phosphorus Alloy, Nanocrystalline (Electrodeposited) |
| SAE AMS 4544 H: 2017 | NICKEL-COPPER ALLOY, CORROSION RESISTANT, SHEET, STRIP, AND PLATE 67NI - 30CU, ANNEALED |
| API 5ST : 2010 : R2015 | SPECIFICATION FOR COILED TUBING |
| GGG-K-275 Revision D:1974 | KEY, SOCKET HEAD SCREW AND KEY SETS SOCKET HEAD (WRENCH, HEXAGON, SPLINE AND SQUARE) |
| SAE AMS 6323 : 2017 | STEEL, MECHANICAL TUBING 0.50CR - 0.55NI - 0.25MO (0.38 - 0.43C) (SAE 8740) |
| ASTM F 3302 : 2018 | Standard for Additive Manufacturing – Finished Part Properties – Standard Specification for Titanium Alloys via Powder Bed Fusion |
| ASTM F 2162 : 2001 : R2016 | Standard Specification for Bearing, Roller, Needle: Drawn Outer Ring, Full Complement, Without Inner Ring, Open and Closed End, Standard Type |
| SAE AMS 5892 : 2014 | ALLOY, SHEET AND STRIP, 42FE - 37.5NI - 14CO - 4.8CB (NB) - 1.6TI, SOLUTION HEAT TREATED, PRECIPITATION HARDENABLE, MULTIPLE MELTED, HIGH TEMPERATURE, LOW EXPANSION |
| A-A-52202 Revision C:2012 | OPENER, CAN, HAND, FOR SQUARE AND ROUND FOOD CANS |
| ABMA 10A : 2001 | METAL BALLS FOR UNGROUND BEARINGS AND OTHER USES |
| SAE AMS 6477 : 2015 | STEEL, BARS, FORGINGS, AND TUBING, 0.80CR (0.90 - 1.03C), FOR BEARING APPLICATIONS |
| SAE AMS 6358 : 2016 | STEEL SHEET, STRIP, AND PLATE, 0.50CR - 0.55NI - 0.25MO (0.38 - 0.43C) (SAE 8740) |
| SAE ARP 1341 : 2010 | DETERMINING DECARBURIZATION AND CARBURIZATION IN FINISHED PARTS OF CARBON AND LOW-ALLOY STEELS |
| SAE AMS 6539 : 2013 | STEEL BARS, FORGINGS, AND TUBING, 1.7CR - 3.8NI - 0.3MO - (0.32-0.38 C), AIRCRAFT-QUALITY |
| ASTM B 477 : 1997 | Standard Specification for Gold-Silver-Nickel Electrical Contact Alloy |
| SAE AMS 6324 : 2014 | STEEL BARS, FORGINGS, AND TUBING, 0.65CR - 0.70NI - 0.25MO (0.38 - 0.43C) (8740 MODIFIED) |
| SAE AMS 7855 : 2017 | COLUMBIUM (NIOBIUM) ALLOY BARS, RODS, AND WIRE, 10W - 2.5ZR, RECRYSTALLIZED |
| SAE AMS 4917 : 2017 | TITANIUM ALLOY SHEET, STRIP, AND PLATE 13.5V - 11CR - 3.0AL - SOLUTION HEAT TREATED |
| SAE AMS 6415 : 2016 | STEEL, BARS, FORGINGS, AND TUBING 0.80CR - 1.8NI - 0.25MO (0.38 - 0.43C) (SAE 4340) |
| SAE AMS 6490 : 2014 | STEEL BARS, FORGINGS, AND TUBING 4.0CR - 4.2MO - 1.0V (0.77 - 0.85C) (M-50) PREMIUM AIRCRAFT-QUALITY FOR BEARING APPLICATIONS CONSUMABLE ELECTRODE VACUUM MELTED |
| SAE AMS 6381 : 2017 | STEEL, MECHANICAL TUBING, 0.95CR - 0.20MO (0.38 - 0.43C) (SAE 4140) |
| SAE AMS 6414 : 2016 | STEEL, BARS, FORGINGS, AND TUBING 0.80CR - 1.8NI - 0.25MO (0.38 - 0.43C) (SAE 4340) VACUUM CONSUMABLE ELECTRODE REMELTED |
| SAE AMS 5529 : 2012 | STEEL, CORROSION RESISTANT, SHEET AND STRIP, 17CR - 7.1NI - 1.1AL, SOLUTION HEAT TREATED AND COLD ROLLED, PRECIPITATION HARDENABLE, 0.0015 TO 0.100 INCH (0.038 TO 2.54 MM) NOMINAL THICKNESS |
| SAE AMS 4899 : 2016 | TITANIUM ALLOY, SHEET, STRIP, AND PLATE, 4.5AI - 3V - 2FE - 2MO, ANNEALED |
| SAE AMS 4986 : 2015 | TITANIUM ALLOY, FORGINGS, 10V - 2FE - 3AL, CONSUMABLE ELECTRODE MELTED, SINGLE-STEP SOLUTION HEAT TREATED AND OVERAGED, 160 KSI (1103 MPA) TENSILE STRENGTH |
| SAE AMS 5120 : 2013 | STEEL STRIP, 0.68 - 0.80C (SAE 1074) |
| SAE AMS 5632 : 2018 | STEEL, CORROSION-RESISTANT, BARS, WIRE, AND FORGINGS, 17CR - 0.50MO (0.95 - 1.20C) (440F), FREE-MACHINING, ANNEALED |
| API 5C8 : 2017 | CARE, MAINTENANCE, AND INSPECTION OF COILED TUBING |
| SAE AMS 6437 : 2015 | STEEL, SHEET, STRIP, AND PLATE, 5.0CR - 1.3MO - 0.50V (0.38 - 0.43C) (H-11) |
| ASTM B 596 : 1989 : R2012 | Standard Specification for Gold-Copper Alloy Electrical Contact Material |
| API 17E REDLINE : 2010 | SPECIFICATION FOR SUBSEA UMBILICALS |
| SAE AMS 6346 : 2013 | STEEL BARS, 0.95CR - 0.20MO (0.28 TO 0.33C) (SAE 4130), HARDENED AND TEMPERED, 125 KSI (862 MPA) TENSILE STRENGTH |
| SAE AMS 5517 : 2010 | STEEL, CORROSION RESISTANT, SHEET AND STRIP, 18CR - 8NI (301) COLD ROLLED, 125 KSI (862 MPA) TENSILE STRENGTH |
| SAE AMS 6303 : 2018 | STEEL BARS AND FORGINGS, LOW ALLOY, HEAT-RESISTANT, 0.65SI - 1.25CR - 0.50MO - 0.85V (0.25 - 0.30C) |
| SAE AMS 5518 : 2014 | STEEL, CORROSION RESISTANT, SHEET AND STRIP 18CR - 8NI COLD ROLLED, 150 KSI (1034 MPA) TENSILE STRENGTH |
| SAE AMS 6365 : 2014 | STEEL TUBING, SEAMLESS, 0.95CR - 0.20MO (0.33 - 0.38C) (SAE 4135), NORMALIZED OR STRESS RELIEVED |
| API 16AR : 2017 | STANDARD FOR REPAIR AND REMANUFACTURE OF DRILL-THROUGH EQUIPMENT |
| AGMA 942 : A2012(R2017) | METALLURGICAL SPECIFICATIONS FOR POWDER METALLURGY, PM, STEEL GEARING |
| API SPEC 11AX : 2015 | SPECIFICATION FOR SUBSURFACE SUCKER ROD PUMP ASSEMBLIES, COMPONENTS, AND FITTINGS |
| SAE AMS 6281 : 2015 | STEEL, MECHANICAL TUBING, 0.50CR - 0.55NI - 0.20MO (0.28 - 0.33C) (SAE 8630) |
| SAE AMS 5878 : 2015 | NICKEL ALLOY, CORROSION AND HEAT-RESISTANT, SHEET, STRIP, AND PLATE, 59NI - 22CR - 2MO - 14W - 0.35AI - 0.03LA, SOLUTION HEAT TREATED |
| CAN/CSA-Z662-15 | Oil and gas pipeline systems |
| ISO 3183:2012 | Petroleum and natural gas industries Steel pipe for pipeline transportation systems |
| SAE AMS 5525 : 2012 | STEEL, CORROSION AND HEAT RESISTANT, SHEET, STRIP, AND PLATE 15CR - 25.5NI - 1.2MO - 2.1TI - 0.006B - 0.30V, 1800 DEGREE F (982 DEGREE C) SOLUTION HEAT TREATED |
| SAE AMS 6444 : 2015 | STEEL, BARS, FORGINGS, AND TUBING, 1.45CR (0.93 - 1.05C) (SAE 52100), PREMIUM AIRCRAFT-QUALITY, CONSUMABLE ELECTRODE VACUUM REMELTED |
| ICEA S 89 648 : 2011 | AERIAL SERVICE WIRE TECHNICAL REQUIREMENTS |
| ASTM B 540 : 1997 : R2008 | Standard Specification for Palladium Electrical Contact Alloy |
| ASTM A 880 : 1995 | Standard Practice for Criteria for Use in Evaluation of Testing Laboratories and Organizations for Examination and Inspection of Steel, Stainless Steel, and Related Alloys (Withdrawn 2004) |
| ASTM F 2328 : 2017 : REDLINE | Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts |
| ASTM F 2511 : 2005 : EDT 1 | Standard Specification for Rollers, Bearing, Needle, Ferrous, Solid |
| ASTM B 933 : 2016 : REDLINE | Standard Test Method for Microindentation Hardness of Powder Metallurgy (PM) Materials |
| SAE AMS 6497 : 2013 | STEEL BARS, FORGINGS, AND TUBING, NITRIDING 1.4CR - 1.2MO - 0.3V (0.29 - 0.36C), ELECTROSLAG REMELTED OR CONSUMABLE ELECTRODE VACUUM REMELTED, PREMIUM AIRCRAFT-QUALITY FOR BEARING APPLICATIONS |
| ASTM B 277 : 1995 : R2001 | Standard Test Method for Hardness of Electrical Contact Materials |
| ASTM B 540 : 1997 : R2008 : EDT 1 | Standard Specification for Palladium Electrical Contact Alloy |
| ASTM B 596 : 1989 : R1999 | Standard Specification for Gold-Copper Alloy Electrical Contact Material |
| ASTM B 684 : 1997 | Standard Specification for Platinum-Iridium Electrical Contact Materials |
| ASTM A 771/A771M : 1995 | Standard Specification for Seamless Austenitic and Martensitic Stainless Steel Tubing for Liquid Metal-Cooled Reactor Core Components |
| NACE SP 04 72 : 2015 | METHODS AND CONTROLS TO PREVENT IN-SERVICE ENVIRONMENTAL CRACKING OF CARBON STEEL WELDMENTS IN CORROSIVE PETROLEUM REFINING ENVIRONMENTS |
| UNI EN ISO 4498 : 2010 | SINTERED METAL MATERIALS, EXCLUDING HARDMETALS - DETERMINATION OF APPARENT HARDNESS AND MICROHARDNESS |
| UNI EN ISO 13628-2 : 2007 | PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 2: UNBONDED FLEXIBLE PIPE SYSTEMS FOR SUBSEA AND MARINE APPLICATIONS |
| SAE AMS 6439 : 2016 | STEEL SHEET, STRIP, AND PLATE, 1.05CR - 0.55NI - 1.0MO - 0.12V (0.42 - 0.48C) (D6AC), CONSUMABLE ELECTRODE VACUUM MELTED, ANNEALED |
| SAE AMS 2759/10 : 2014 | AUTOMATED GASEOUS NITRIDING CONTROLLED BY NITRIDING POTENTIAL |
| SAE AMS 6429 : 2014 | STEEL BARS, FORGINGS, TUBING, AND RINGS 0.78CR - 1.8NI - 0.35MO - 0.20V (0.33 - 0.38C) (4335 MOD) CONSUMABLE ELECTRODE VACUUM MELTED |
| SAE AMS 4939C : 2017 | TITANIUM ALLOY SHEET, STRIP, AND PLATE, 3AL - 8V - 6CR - 4MO - 4ZR, SOLUTION HEAT TREATED |
| MIL-DTL-45204 Revision D:2007 | Gold Plating, Electrodeposited |
| AGMA 923 : B | METALLURGICAL SPECIFICATIONS OF STEEL GEARING |
| API SPEC 11B CHINESE : 2010 | SPECIFICATION FOR SUCKER RODS, POLISHED RODS AND LINERS, COUPLINGS, SINKER BARS, POLISHED ROD CLAMPS, STUFFING BOXES, AND PUMPING TEES |
| SAE AMS 6482 : 2015 | STEEL BARS, FORGINGS, AND TUBING, 1.5SI - 1.25CR - 3.8NI - 0.50MO - 0.30V (0.40C) VACUUM REMELTED, ANNEALED |
| SAE AMS 2436 : 2011 | COATING, ALUMINUM OXIDE DETONATION DEPOSITION |
| SAE AMS 2773 : 2013 | HEAT TREATMENT, CAST NICKEL ALLOY AND COBALT ALLOY PARTS |
| UNI EN ISO 13628-5 : 2010 | PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 5: SUBSEA UMBILICALS |
| SAE AMS 6499 : 2015 | STEEL, BARS, FORGINGS, AND TUBING, 2.7SI - 0.85CR - 1.8NI - 0.4MO - 0.2V - (0.37 - 0.44C), DOUBLE VACUUM MELTED |
| SAE AMS 5749 : 2014 | STEEL, CORROSION-RESISTANT, BARS, WIRE, FORGINGS, AND TUBING 14.5CR - 4.0MO - 1.2V (1.10-1.20C) PREMIUM QUALITY FOR BEARING APPLICATIONS, DOUBLE VACUUM MELTED |
| SAE AMS 6493 : 2013 | STEEL BARS, FORGINGS, AND TUBING, 1.0CR - 3.25NI - 0.40MO (0.17 - 0.22C), ELECTROSLAG REMELTED OR CONSUMABLE ELECTRODE VACUUM REMELTED, PREMIUM AIRCRAFT-QUALITY |
| ASTM E 10 : 2017-05 | TEST METHOD FOR BRINELL HARDNESS OF METALLIC MATERIALS |
| SAE AMS 2406 : 2015 | PLATING, CHROMIUM, HARD DEPOSIT |
| SAE AMS 6951 : 2017 | TITANIUM ALLOY, SHEET 5AL - 4V - 0.75MO - 0.5FE ANNEALED |
| API SPEC 19TT : 2016 | SPECIFICATION FOR DOWNHOLE WELL TEST TOOLS AND RELATED EQUIPMENT |
| SAE AMS 6496 : 2013 | STEEL BARS, FORGINGS, AND TUBING, NITRIDING, 1.4CR - 1.2MO - 0.3V (0.29 - 0.36C) AIRCRAFT-QUALITY FOR BEARING APPLICATIONS |
| SAE AMS 6484 : 2016 | STEEL, BARS, FORGINGS, AND TUBING 0.80CR - 1.8NI - 0.25MO (0.38 - 0.43C) (SAE 4340) NORMALIZED AND TEMPERED |
| SAE AMS 6372 : 2017 | STEEL, MECHANICAL TUBING, 0.95CR - 0.20MO (0.33 - 0.38C) (SAE 4135) |
| ASTM F 606/F606M : 2016 : REDLINE | Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets |
| ASTM F 837M : 2016 : REDLINE | Standard Specification for Stainless Steel Socket Head Cap Screws [Metric] |
| SAE AMS 6351 : 2015 | STEEL, SHEET, STRIP, AND PLATE, 0.95CR - 0.20MO (0.28 - 0.33C) (SAE 4130), SPHEROIDIZED |
| SAE J 2175 : 2015 | SPECIFICATIONS FOR LOW CARBON CAST STEEL SHOT |
| BS EN ISO 15156-3:2015 | Petroleum and natural gas industries. Materials for use in H2S-containing environments in oil and gas production Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys |
| SAE AMS 2759/6 : 2005 | GAS NITRIDING OF LOW-ALLOY STEEL PARTS |
| SAE AMS 5951 : 2017 | NICKEL ALLOY, CORROSION AND HEAT-RESISTANT, SHEET, STRIP, AND PLATE, 57NI - 20CR - 10CO - 8.5MO - 2.1TI - 1.5AL - 0.005B, VACUUM INDUCTION AND CONSUMABLE ELECTRODE MELTED, SOLUTION HEAT TREATED, PRECIPITATION HEAT TREATABLE |
| SAE AMS 6382 : 2014 | STEEL, BARS, FORGINGS, AND RINGS 0.95CR - 0.20MO (0.38 - 0.43C) (SAE 4140) ANNEALED |
| MIL-STD-2197 Revision A:2012 | BRUSH ELECTROPLATING ON MARINE MACHINERY |
| ASTM B 684 : 1997 : R2008 | Standard Specification for Platinum-Iridium Electrical Contact Materials |
| BS 3828:1973 | Specification for crystal glass |
| MIL C 26074 : E | COATINGS, ELECTROLESS NICKEL, REQUIREMENTS FOR |
| SAE AMS 6492 : 2013 | STEEL BARS, FORGINGS, AND TUBING, 1.0CR - 3.25NI - 0.40MO (0.17 - 0.22C) AIRCRAFT QUALITY |
| SAE J 2270 : 2016 | SHIP SYSTEMS AND EQUIPMENT - THREADED FASTENERS - INSPECTION, TEST, AND INSTALLATION GUIDANCE |
| ASTM B 613 : 2017 : REDLINE | Standard Guide for Preparing Specifications for Miniature Brushes of Composite Materials for Sliding Electric Contacts |
| SAE AMS 6317K : 2017 | STEEL BARS AND FORGINGS, 1.8NI - 0.25MO (0.38 - 0.43C) (4640), HEAT TREATED, 125 KSI (862 MPA) TENSILE STRENGTH |
| SAE AMS C 26074 : 2013 | ELECTROLESS NICKEL COATINGS |
| SAE AMS 5912 : 2014 | STEEL, CORROSION-RESISTANT, SHEET AND STRIP, 19CR - 9.2NI (SAE 30304), COLD ROLLED, 3/4 HARD, 175 KSI (1207 MPA) TENSILE STRENGTH |
| ASTM B 578 : 1987 : R2004 | Standard Test Method for Microhardness of Electroplated Coatings |
| SAE AMS 6362 : 2014 | STEEL TUBING, SEAMLESS, 0.95CR - 0.20MO (0.28 - 0.33C) (SAE 4130), 150 KSI (1034 MPA) TENSILE STRENGTH |
| ASTM F 1459 : 2006 : R2012 | Standard Test Method for Determination of the Susceptibility of Metallic Materials to Hydrogen Gas Embrittlement (HGE) |
| SAE ARP 5483/2 : 2017 | ROLLING ELEMENT BEARING HARDNESS TEST |
| SAE AMS 6312 : 2015 | STEEL BARS, FORGINGS, AND TUBING, 1.8NI - 0.25MO (0.38 - 0.43C) (4640) |
| SAE AMS 6438 : 2001(S2016) | STEEL, SHEET, STRIP, AND PLATE, 1.05CR - 0.55NI - 1.0MO - 0.12V (0.45 - 0.50C) CONSUMABLE ELECTRODE VACUUM MELTED |
| ASTM B 684/B684M : 2016 : REDLINE | Standard Specification for Platinum-Iridium Electrical Contact Materials |
| ASTM B 832 : 1993 : R2013 | Standard Guide for Electroforming with Nickel and Copper |
| SAE AMS 4915 : 2017 | TITANIUM ALLOY SHEET, STRIP, AND PLATE 8AL - 1V - 1MO SINGLE ANNEALED |
| SAE AMS 6423 : 2016 | STEEL BARS, FORGINGS, AND TUBING, 0.92CR - 0.75NI - 0.52MO - 0.003B - 0.04V (MODIFIED 98BV40) |
| SAE AMS 6361 : 2014 | STEEL TUBING, SEAMLESS, 0.95CR - 0.20MO (0.28 - 0.33C) (SAE 4130) 125 KSI (862 MPA) TENSILE STRENGTH |
| SAE AMS 4989 : 2014 | TITANIUM ALLOY SHEET, STRIP, AND PLATE, 3AL - 2.5V, ANNEALED |
| SAE AMS 7848 : 2015( | TANTALUM ALLOY, BARS AND RODS, 90TA - 10W |
| SAE AMS 6325 : 2015 | STEEL, BARS, AND FORGINGS 0.50CR - 0.55NI - 0.25MO (0.38 - 0.43C) (SAE 8740) HEAT TREATED, 105 KSI (724 MPA) TENSILE STRENGTH |
| API SPEC 16C : 2015 | CHOKE AND KILL EQUIPMENT |
| SAE AMS 4904 : 2015 | TITANIUM ALLOY SHEET, STRIP, AND PLATE, 6AL - 4V, SOLUTION HEAT TREATED AND AGED |
| SAE AMS6474B:2008(S2018) | FORGINGS, HARDENABLE STEELS AND CORROSION-RESISTANT STEELS HEAT-TREATED, FINISHED-PART PROPERTIES SHORT-TRANSVERSE TENSILE STRENGTH AND FRACTURE TOUGHNESS |
| API 17J REDLINE : 2008 | SPECIFICATION FOR UNBONDED FLEXIBLE PIPE |
| SAE AMS 5904 : 2012 | STEEL, CORROSION-RESISTANT, SHEET AND STRIP, 18CR - 9.0NI (SAE 30302), COLD ROLLED, 1/2 HARD, 150 KSI (1034 MPA) TENSILE STRENGTH |
| SAE AMS 2431 : 2018 | PEENING MEDIA, GENERAL REQUIREMENTS |
| SAE AMS 4900 : 2014 | TITANIUM SHEET, STRIP, AND PLATE, COMMERCIALLY PURE, ANNEALED, 55.0 KSI (379 MPA) YIELD STRENGTH |
| ASTM C 730 : 1998 | Standard Test Method for Knoop Indentation Hardness of Glass |
| SAE AMS 6419 : 2015 | STEEL, BARS, FORGINGS, AND TUBING, 1.6SI - 0.82CR - 1.8NI - 0.40MO - 0.08V (0.40 - 0.45C), CONSUMABLE ELECTRODE VACUUM REMELTED |
| API 5ST CHINESE : 2010 | SPECIFICATION FOR COILED TUBING |
| SAE AMS 6529 : 2017 | STEEL, BARS, 0.95CR - 0.20MO (0.38 - 0.43C) (SAE 4140), SPECIAL AIRCRAFT-QUALITY CLEANLINESS, NORMALIZED |
| ASTM B 832 : 1993 : R2018 | Standard Guide for Electroforming with Nickel and Copper |
| SAE AMS 6373 : 2016 | STEEL, WELDED TUBING, 0.95CR - 0.20MO (0.28 - 0.33C) (SAE 4130) |
| SAE AMS 6448 : 2013 | STEEL, BARS, FORGINGS AND TUBING 0.95CR - 0.22V (0.48 - 0.53C) (SAE 6150) |
| UNI EN ISO 3183 : 2012 | PETROLEUM AND NATURAL GAS INDUSTRIES - STEEL PIPE FOR PIPELINE TRANSPORTATION SYSTEMS |
| SAE AMS 6305 : 2016 | STEEL, HEAT-RESISTANT, BARS, FORGINGS, AND TUBING, 0.95CR - 0.55MO - 0.30V (0.40 - 0.50C), VACUUM ARC REMELTED |
| SAE AMS 6424 : 2017 | STEEL BARS, FORGINGS, AND TUBING 0.80CR - 1.8NI - 0.25MO (0.49 - 0.55C) |
| SAE AMS 7847D : 2015 | TANTALUM ALLOY SHEET, STRIP, AND PLATE, 90TA - 10W |
| I.S. EN ISO 17945:2015 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - METALLIC MATERIALS RESISTANT TO SULFIDE STRESS CRACKING IN CORROSIVE PETROLEUM REFINING ENVIRONMENTS (ISO 17945:2015) |
| SAE AMS 2435 : 2017 | COATING, TUNGSTEN CARBIDE-COBALT COATING, DETONATION PROCESS |
| SAE AMS 6435 : 2017 | STEEL, SHEET, STRIP, AND PLATE, 0.75MN - 0.78CR - 1.8NI - 0.35MO - 0.20V (0.33 - 0.38C) (4335 MOD), VACUUM CONSUMABLE ELECTRODE MELTED, ANNEALED |
| API 5LD : 2017 | CRA CLAD OR LINED STEEL PIPE |
| SAE AMS 2775 : 2015 | CASE HARDENING OF TITANIUM AND TITANIUM ALLOYS |
| ASTM C 1326 : 2013 : R2018 | Standard Test Method for Knoop Indentation Hardness of Advanced Ceramics |
| SAE AMS 6560 : 2013 | STEEL BARS, WIRE AND FORGINGS 10CO - 7MO - 6V - 6W - 4CR (2.2 - 2.4C) PREMIUM AIRCRAFT-QUALITY FOR BEARING APPLICATIONS INERT GAS ATOMIZED AND HOT ISOSTATICALLY PRESSED CONSOLIDATED |
| ASTM F 1459 : 2006 : R2017 | Standard Test Method for Determination of the Susceptibility of Metallic Materials to Hydrogen Gas Embrittlement (HGE) |
| ASTM A 677 : 2016 : REDLINE | Standard Specification for Nonoriented Electrical Steel Fully Processed Types |
| ASTM E 92 : 2017 : REDLINE | Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials |
| ASTM A 1100 : 2016 | Standard Guide for Qualification and Control of Induction Heat Treating |
| ASTM F 3122 : 2014 | Standard Guide for Evaluating Mechanical Properties of Metal Materials Made via Additive Manufacturing Processes |
| ASTM B 540 : 1997 : R2002 | Standard Specification for Palladium Electrical Contact Alloy |
| ASTM F 3160 : 2016 | Standard Guide for Metallurgical Characterization of Absorbable Metallic Materials for Medical Implants |
| SAE AMS6481D:2017 | STEEL BARS, FORGINGS, AND TUBING, NITRIDING, 3CR - 1MO - 0.2V - (0.29 - 0.36C), PREMIUM AIRCRAFT-QUALITY FOR BEARING APPLICATIONS, DOUBLE VACUUM MELTED |
| ASTM B 578 : 1987 : R2009 | Standard Test Method for Microhardness of Electroplated Coatings |
| ASTM C 522 : 2003 : R2009 | Standard Test Method for Airflow Resistance of Acoustical Materials |
| ASTM B 541 : 2001 : R2006 | Standard Specification for Gold Electrical Contact Alloy |
| ASTM F 2162 : 2001 : EDT 1 | Standard Specification for Bearing, Roller, Needle: Drawn Outer Ring, Full Complement, Without Inner Ring, Open and Closed End, Standard Type |
| ASTM B 832 : 1993 : R1998 | Standard Guide for Electroforming with Nickel and Copper |
| ASTM F 2162 : 2001 : R2008 | Standard Specification for Bearing, Roller, Needle: Drawn Outer Ring, Full Complement, Without Inner Ring, Open and Closed End, Standard Type |
| ONORM EN ISO 3183 : 2013 | PETROLEUM AND NATURAL GAS INDUSTRIES - STEEL PIPE FOR PIPELINE TRANSPORTATION SYSTEMS (ISO 3183:2012) |
| BS EN ISO 15156-2:2015 | Petroleum and natural gas industries. Materials for use in H2S-containing environments in oil and gas production Cracking-resistant carbon and low alloy steels, and the use of cast irons |
| ISO 15156-3:2015 | Petroleum and natural gas industries Materials for use in H2S-containing environments in oil and gas production Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys |
| BS EN ISO 4498:2010 | Sintered metal materials, excluding hardmetals. Determination of apparent hardness and microhardness |
| ISO 4498:2010 | Sintered metal materials, excluding hardmetals Determination of apparent hardness and microhardness |
| ISO 15156-2:2015 | Petroleum and natural gas industries Materials for use in H2S-containing environments in oil and gas production Part 2: Cracking-resistant carbon and low-alloy steels, and the use of cast irons |
| ISO 13628-5:2009 | Petroleum and natural gas industries Design and operation of subsea production systems Part 5: Subsea umbilicals |
| ISO 13628-2:2006 | Petroleum and natural gas industries Design and operation of subsea production systems Part 2: Unbonded flexible pipe systems for subsea and marine applications |
| ISO 17945:2015 | Petroleum, petrochemical and natural gas industries Metallic materials resistant to sulfide stress cracking in corrosive petroleum refining environments |
| EN ISO 17945:2015 | Petroleum, petrochemical and natural gas industries - Metallic materials resistant to sulfide stress cracking in corrosive petroleum refining environments (ISO 17945:2015) |
| EN 843-4 : 2005 | ADVANCED TECHNICAL CERAMICS - MECHANICAL PROPERTIES OF MONOLITHIC CERAMICS AT ROOM TEMPERATURE - PART 4: VICKERS, KNOOP AND ROCKWELL SUPERFICIAL HARDNESS |
| EN ISO 4498:2010 | Sintered metal materials, excluding hardmetals - Determination of apparent hardness and microhardness (ISO 4498:2010) |
| EN ISO 13628-5:2009 | Petroleum and natural gas industries - Design and operation of subsea production systems - Part 5: Subsea umbilicals (ISO 13628-5:2009) |
| ASTM F 880M : 2016 : REDLINE | Standard Specification for Stainless Steel Socket Set Screws (Metric) |
| API 5C7 : 1996 : R2007 | RECOMMENDED PRACTICE FOR COILED TUBING OPERATIONS IN OIL AND GAS WELL SERVICES |
| API STD 1104:2013 | WELDING OF PIPELINES AND RELATED FACILITIES |
| SAE AMS 2438 : 2015 | PLATING, CHROMIUM, THIN, HARD, DENSE DEPOSIT |
| ASTM F 364 : 1996 : R2019 | Standard Specification for Molybdenum Flattened Wire for Electron Tubes |
| ASTM F 364 : 1996 | Standard Specification for Molybdenum Flattened Wire for Electron Tubes |
| SAE AMS 7735 : 2018 | ALLOY WIRE, ROUND, 35PD - 30AG - 14CU - 10AU - 10PT - 0.85ZN, SOLUTION HEAT TREATED |
| SAE AMS 6430J : 2017 | STEEL, BARS, FORGINGS, TUBING, AND RINGS, 0.75MN - 0.78CR - 1.8NI - 0.35MO - 0.20V (0.32 - 0.38C), (4335 MODIFIED) |
| SAE AMS 4988 : 2014 | TITANIUM ALLOY SHEET, STRIP, AND PLATE, 6AL - 6V - 2SN, SOLUTION HEAT TREATED |
| SAE AMS 6526 : 2016 | STEEL, BARS, FORGINGS, TUBING, AND RINGS, 1.0CR - 7.5NI - 4.5CO - 1.0MO - 0.09V (0.29 - 0.34C), CONSUMABLE ELECTRODE VACUUM REMELTED, ANNEALED |
| NACE MR 01 75 : 2003 | METALS FOR SULFIDE STRESS CRACKING AND STRESS CORROSION CRACKING RESISTANCE IN SOUR OILFIELD ENVIRONMENTS |
| SAE AMS 6498 : 2013 | STEEL BARS, FORGINGS, AND TUBING, NITRIDING, 1.4CR - 1.2MO - 0.3V (0.29 - 0.36C), DOUBLE VACUUM MELTED, PREMIUM AIRCRAFT-QUALITY FOR BEARING APPLICATIONS |
| SAE AMS 6421 : 2016 | STEEL BARS, FORGINGS, AND TUBING 0.80CR - 0.85NI - 0.20MO - 0.003B (0.35 - 0.40C) (MODIFIED 98B37) |
| MIL W 12133 : D | WASHER, SPRING TENSION GENERAL SPECIFICATION FOR |
| API 1104 PORTUGUESE : 2013 | WELDING OF PIPELINES AND RELATED FACILITIES |
| SAE AMS 2745 : 2012 | INDUCTION HARDENING OF STEEL PARTS |
| SAE AMS 6408 : 2018 | STEEL, HOTWORK TOOL, BARS AND FORGINGS, 5.25CR - 1.5MO - 1.0V (0.35-0.45C) (H-13), ELECTROSLAG REMELTED (ESR) OR CONSUMABLE ELECTRODE VACUUM ARC REMELTED (VAR), ANNEALED |
| ASTM B 477 : 1997 : R2012 | Standard Specification for Gold-Silver-Nickel Electrical Contact Alloy |
| MIL-STD-1886 Base Document:1998 | TUNGSTEN CARBIDE COBALT COATING, DETONATION PROCESS FOR |
| API 16A : 2017 | SPECIFICATION FOR DRILL-THROUGH EQUIPMENT |
| SAE AMS 5553 : 2018 | NICKEL, SHEET AND STRIP, LOW (0.02 MAX) CARBON, ANNEALED |
| SAE AMS 6425 : 2015 | STEEL, BARS, FORGINGS, AND TUBING, 1.4MN - 1.5SI - 0.30CR - 1.8NI - 0.40MO (0.23 - 0.28C), CONSUMABLE ELECTRODE VACUUM MELTED |
| SAE AMS 6395 : 2015 | STEEL SHEET, STRIP, AND PLATE, 0.95CR - 0.20MO (0.38 - 0.43C) (SAE 4140) |
| DIN EN ISO 17945:2015-08 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - METALLIC MATERIALS RESISTANT TO SULFIDE STRESS CRACKING IN CORROSIVE PETROLEUM REFINING ENVIRONMENTS (ISO 17945:2015) |
| SAE AMS 4983 : 2015 | TITANIUM ALLOY, FORGINGS, 10V - 2FE - 3AL, CONSUMABLE ELECTRODE MELTED, SINGLE-STEP SOLUTION HEAT TREATED AND AGED, 180 KSI (1241 MPA) TENSILE STRENGTH |
| ASTM B 541 : 2001 : R2012 | Standard Specification for Gold Electrical Contact Alloy |
| SAE AMS 5620 : 2012 | STEEL, CORROSION AND HEAT-RESISTANT, BARS, WIRE, AND FORGINGS, 13CR (0.30 - 0.40C) (SAE 51420F, 51420FSE), FREE-MACHINING GRADE |
| ASTM B 684 : 1997 : R2002 | Standard Specification for Platinum-Iridium Electrical Contact Materials |
| MIL-DTL-70794 Revision A:2006 | PROJECTILE, M940 - 20 MM, MULTIPURPOSE, TRACE SELF-DESTRUCT, METAL PARTS |
| MIL G 45204 : C | GOLD PLATING, ELECTRODEPOSITED |
| ASTM E 606/E606M : 2012 : REDLINE | Standard Test Method for Strain-Controlled Fatigue Testing |
| BS 7253-2:1990 | Non-metallic materials for surgical implants Specification for ceramic materials based on alumina |
| BS EN ISO 13628-5:2009 | Petroleum and natural gas industries. Design and operation of subsea production systems Subsea umbilicals |
| API 2SF : 2013 | MANUFACTURE OF STRUCTURAL STEEL FORGINGS FOR PRIMARY OFFSHORE APPLICATIONS |
| API SPEC 17J : 2014 | SPECIFICATION FOR UNBONDED FLEXIBLE PIPE |
| ASTM B 832 : 1993 : R2008 | Standard Guide for Electroforming with Nickel and Copper |
| CSA Z245.1 : 2014 | STEEL PIPE |
| SAE AMS 2757 : 2010 | GASEOUS NITROCARBURIZING |
| SAE J 1993 : 2013 | HIGH-CARBON CAST-STEEL GRIT |
| SAE AMS 6491 : 2014 | STEEL BARS, FORGINGS, AND TUBING 4.1CR - 4.2MO - 1.0V (0.80 - 0.85C) (M-50) PREMIUM AIRCRAFT-QUALITY FOR BEARING APPLICATIONS, DOUBLE VACUUM MELTED |
| SAE AMS 6411 : 2018 | STEEL BARS, FORGINGS, AND TUBING, 0.88CR - 1.8NI - 0.42MO - 0.08V (0.28 - 0.33C) (4330 MOD) CONSUMABLE ELECTRODE REMELTED |
| SAE AMS 2423 : 2015 | PLATING, NICKEL, HARD DEPOSIT |
| SAE AMS 5606 : 2013 | ALLOY, CORROSION AND HEAT-RESISTANT, SHEET, STRIP, AND PLATE 41.5NI - 16CR - 37FE - 2.9CB (NB) - 1.8TI CONSUMABLE ELECTRODE OR VACUUM INDUCTION MELTED 1750 DEGREES F (954 DEGREES C) SOLUTION HEAT TREATED |
| SAE AMS 6357 : 2015 | STEEL SHEET, STRIP, AND PLATE, 0.50CR - 0.55NI - 0.25MO (0.33 - 0.38C) (8735) |
| SAE AMS 6396 : 2015 | STEEL SHEET, STRIP, AND PLATE, 0.80CR - 1.8NI - 0.25MO (0.49 - 0.55C) ANNEALED |
| SAE AMS 6495 : 2016 | STEEL BARS, FORGINGS, AND TUBING, 1.0CR - 2.50NI - 2.0MO - 1.10SI (0.10 - 0.20C), PREMIUM AIRCRAFT-QUALITY, ELECTROSLAG REMELTED OR CONSUMABLE ELECTRODE VACUUM REMELTED |
| SAE AMS 2460 : 2013 | PLATING, CHROMIUM |
| SAE AMS 6407 : 2017 | STEEL, BARS, FORGINGS, AND TUBING, 1.2CR - 2.0NI - 0.45MO (0.27 - 0.33C) |
| SAE AMS 6322 : 2014 | STEEL BARS, FORGINGS, AND RINGS, 0.50CR - 0.55NI - 0.25MO (0.38 - 0.43C) (SAE 8740) |
| SAE AMS 6265 : 2016 | STEEL, BARS, FORGINGS, AND TUBING, 1.2CR - 3.25NI - 0.12MO (0.07 - 0.13C) (9310), VACUUM CONSUMABLE ELECTRODE REMELTED |
| SAE AMS 5899 : 2013 | STEEL, CORROSION-RESISTANT, BARS, WIRE, AND FORGINGS, 17CR - 0.52MO (0.95 - 1.20C), POWDER METALLURGY PRODUCT, HOT ISOSTATICALLY PRESSED |
| SAE AMS 6349 : 2017 | STEEL BARS, 0.95CR - 0.20MO (0.38 TO 0.43C) (SAE 4140), NORMALIZED |
| SAE AMS 6487 : 2016 | STEEL, BARS, AND FORGINGS, 5.0CR - 1.3MO - 0.50V (0.38 - 0.43C) (H-11), CONSUMABLE ELECTRODE VACUUM MELTED |
| SAE AMS 5630 : 2013 | STEEL, CORROSION-RESISTANT, BARS, WIRE, AND FORGINGS, 17CR - 0.52MO (0.95 - 1.20C) (440C) |
| SAE AMS 5605 : 2013 | NICKEL ALLOY, CORROSION AND HEAT-RESISTANT, SHEET, STRIP, AND PLATE, 41.5NI - 16CR - 37FE - 2.9CB(NB) - 1.8TI, CONSUMABLE ELECTRODE OR VACUUM INDUCTION MELTED, 1800 DEGREES F (982 DEGREES C) SOLUTION HEAT TREATED |
| SAE AS 7101 : 2007 | NATIONAL AEROSPACE AND DEFENSE CONTRACTORS ACCREDITATION PROGRAM (NADCAP) GENERAL REQUIREMENTS FOR MATERIALS TEST LABORATORY ACCREDITATION PROGRAM |
| SAE AMS 2444 : 2011 | COATING, TITANIUM NITRIDE, PHYSICAL VAPOR DEPOSITION |
| ASTM F 2328M : 2017 : REDLINE | Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts (Metric) |
| SAE AMS 5906C : 2018 | STEEL, CORROSION-RESISTANT, SHEET AND STRIP, 18CR - 9.0NI (SAE 30302), COLD ROLLED, FULL HARD, 185 KSI (1276 MPA) TENSILE STRENGTH |
| SAE AMS 6557 : 2013 | STEEL, BARS, WIRE, AND FORGINGS, 9V - 5.25CR - 1.3MO (1.80 - 1.95C), POWDER METALLURGY PRODUCT, HOT ISOSTATICALLY PRESSED |
| SAE AMS 4902 : 2013 | TITANIUM SHEET, STRIP, AND PLATE, COMMERCIALLY-PURE, ANNEALED 40.0 KSI (276 MPA) YIELD STRENGTH |
| SAE AMS 2728 : 2012 | HEAT TREATMENT OF WROUGHT COPPER BERYLLIUM ALLOY PARTS |
| DIN EN ISO 3183:2013-03 | PETROLEUM AND NATURAL GAS INDUSTRIES - STEEL PIPE FOR PIPELINE TRANSPORTATION SYSTEMS (ISO 3183:2012) |
| SAE AMS 6440 : 2015 | STEEL, BARS, FORGINGS, AND TUBING, 1.45CR (0.93 - 1.05C) (SAE 52100), FOR BEARING APPLICATIONS |
| 16/30336547 DC : 0 | BS EN 16602-70-39 - SPACE PRODUCT ASSURANCE - PART 70-39: WELDING OF METALLIC MATERIALS FOR FLIGHT HARDWARE |
| SAE AMS 6523H : 2017 | STEEL, SHEET, STRIP, AND PLATE, 0.75CR - 9.0NI - 4.5CO - 1.0MO - 0.09V (0.17 - 0.23C) VACUUM CONSUMABLE ELECTRODE MELTED, ANNEALED |
| SAE AMS 4918 : 2014 | TITANIUM ALLOY, SHEET, STRIP, AND PLATE, 6AL - 6V - 2SN, ANNEALED |
| API 11AX CHINESE : 2012 | SPECIFICATION FOR SUBSURFACE SUCKER ROD PUMPS AND FITTINGS |
| SAE AMS 6525 : 2016 | STEEL, BARS, FORGINGS, TUBING, AND RINGS, 0.75CR - 9.0NI - 4.5CO - 1.0MO - 0.09V (0.17 - 0.23C), CONSUMABLE ELECTRODE VACUUM MELTED |
| API 16A : 2017 : INC : ERR 1+ERR2+ADD1 : 2018 | SPECIFICATION FOR DRILL-THROUGH EQUIPMENT |
| ASTM B 684 : 1997 : R2012 | Standard Specification for Platinum-Iridium Electrical Contact Materials |
| AWS C2.16 : 1992 | GUIDE FOR THERMAL SPRAY OPERATOR QUALIFICATION |
| SAE AMS 5950 : 2014 | NICKEL ALLOY, CORROSION AND HEAT-RESISTANT, SHEET AND STRIP 52.5NI - 19CR - 3.0MO - 5.0CB - 0.90TI - 0.50AL - 18FE VACUUM INDUCTION AND CONSUMABLE ELECTRODE MELTED SOLUTION HEAT TREATED, PRECIPITATION HARDENABLE |
| SAE AMS 6559 : 2013 | STEEL, BARS, WIRE, AND FORGINGS 9.75V - 5.25CR - 1.3MO (2.40 - 2.55C) POWDER METALLURGY PRODUCT HOT ISOSTATICALLY PRESSED |
| SAE AMS 6371L : 2017 | STEEL, MECHANICAL TUBING, 0.95CR - 0.20MO (0.28 - 0.33C) (SAE 4130) |
| SAE AMS 6471 : 2014 | STEEL, NITRIDING, BARS, FORGINGS, AND TUBING 1.6CR - 0.35MO - 1.13AL (0.38 - 0.43C) (135 MOD) CONSUMABLE ELECTRODE VACUUM MELTED |
| SAE AMS 5901B:2008 | STEEL, CORROSION-RESISTANT, SHEET, STRIP, AND PLATE, 18CR - 8NI (SAE 30301), SOLUTION HEAT TREATED |
| I.S. EN ISO 15156-3:2015&LC:2015 | PETROLEUM AND NATURAL GAS INDUSTRIES - MATERIALS FOR USE IN H[2]S-CONTAINING ENVIRONMENTS IN OIL AND GAS PRODUCTION - PART 3: CRACKING-RESISTANT CRAS (CORROSION-RESISTANT ALLOYS) AND OTHER ALLOYS (ISO 15156-3:2015) |
| SAE AMS 6556 : 2013 | STEEL, BARS, WIRE, AND FORGINGS, 8V - 4CR - 4W - 3MO (2.45 - 2.55C), POWDER METALLURGY PRODUCT, HOT ISOSTATICALLY PRESSED |
| SAE AMS 2448 : 2016 | APPLICATION OF TUNGSTEN CARBIDE COATINGS ON ULTRA HIGH STRENGTH STEELS HIGH VELOCITY OXYGEN/FUEL PROCESS |
| SAE AMS 6345 : 2015 | STEEL, SHEET, STRIP, AND PLATE, 0.95CR - 0.20MO (0.28 - 0.33C) (SAE 4130), NORMALIZED OR OTHERWISE HEAT TREATED |
| SAE AMS 5519 : 2014 | STEEL, CORROSION RESISTANT, SHEET AND STRIP, 18CR - 8NI (SAE 30301) COLD ROLLED, 185 KSI (1276 MPA) TENSILE STRENGTH |
| API TR 17TR8 : 2018 | HIGH-PRESSURE HIGH-TEMPERATURE DESIGN GUIDELINES |
| ASTM B 476 : 2001 | Standard Specification for General Requirements for Wrought Precious Metal Electrical Contact Materials |
| SAE AMS 4911 : 2018 | TITANIUM ALLOY, SHEET, STRIP, AND PLATE, 6AL - 4 V, ANNEALED |
| SAE AMS 6428 : 2014 | STEEL, BARS, FORGINGS, AND TUBING 0.78CR - 1.8NI - 0.35MO - 0.20V (0.32 - 0.38C) (4335 MOD) |
| ASTM E 1268 : 2001 | Standard Practice for Assessing the Degree of Banding or Orientation of Microstructures |
| SAE AMS 6472 : 2014 | STEEL, BARS AND FORGINGS, NITRIDING 1.6CR - 0.35MO - 1.1AL (0.38 - 0.43C) (135 MOD) HARDENED AND TEMPERED, 112 KSI (772 MPA) TENSILE STRENGTH |
| ASTM F 364 : 1996 : R2002 | Standard Specification for Molybdenum Flattened Wire for Electron Tubes |
| SAE AMS 4984F : 2015 | TITANIUM ALLOY FORGINGS, 10V - 2FE - 3AL, CONSUMABLE ELECTRODE MELTED, SOLUTION HEAT TREATED AND AGED, 173 KSI (1193 MPA) TENSILE STRENGTH |
| SAE AMS 6422K : 2016 | STEEL, BARS, FORGINGS, AND TUBING, 0.80CR - 0.85NI - 0.20MO - 0.003B - 0.04V (0.38 - 0.43C) (MODIFIED 98BV40) |
| ASTM E 1187 : 1997 | Standard Terminology Relating to Conformity Assessment (Withdrawn 2006) |
| ASTM F 2162 : 2001 : EDT 2 | Standard Specification for Bearing, Roller, Needle: Drawn Outer Ring, Full Complement, Without Inner Ring, Open and Closed End, Standard Type |
| ASTM B 693 : 2017 : REDLINE | Standard Specification for Silver-Nickel Electrical Contact Materials |
| ASTM B 277 : 1995 : R2012 | Standard Test Method for Hardness of Electrical Contact Materials |
| ASTM F 2162 : 2001 | Standard Specification for Bearing, Roller, Needle: Drawn Outer Ring, Full Complement, Without Inner Ring, Open and Closed End, Standard Type |
| ASTM F 3184 : 2016 | Standard Specification for Additive Manufacturing Stainless Steel Alloy (UNS S31603) with Powder Bed Fusion |
| ASTM B 476 : 2001 : R2012 | Standard Specification for General Requirements for Wrought Precious Metal Electrical Contact Materials |
| ASTM B 476 : 2001 : R2006 | Standard Specification for General Requirements for Wrought Precious Metal Electrical Contact Materials |
| ASTM F 879M : 2016 : REDLINE | Standard Specification for Stainless Steel Socket Button and Flat Countersunk Head Cap Screws (Metric) |
| SAE AMS 5548 : 2012 | STEEL, CORROSION AND HEAT-RESISTANT, SHEET AND STRIP, 16.5CR - 4.5NI - 2.9MO - 0.10N, 1850 TO 1975 DEGREES F (1010 TO 1079 DEGREES C) ANNEALED |
| ASTM F 3318 : 2018 | Standard for Additive Manufacturing – Finished Part Properties – Specification for AlSi10Mg with Powder Bed Fusion – Laser Beam |
| ASTM B 540 : 1997 | Standard Specification for Palladium Electrical Contact Alloy |
| ASTM B 563 : 2001 : R2006 | Standard Specification for Palladium-Silver-Copper Electrical Contact Alloy |
| ASTM F 912 : 2011 | Standard Specification for Alloy Steel Socket Set Screws |
| ASTM F 2511 : 2005 : R2013 | Standard Specification for Rollers, Bearing, Needle, Ferrous, Solid |
| ASTM B 934 : 2015 : REDLINE | Standard Test Method for Effective Case Depth of Ferrous Powder Metallurgy (PM) Parts Using Microindentation Hardness Measurements |
| EN ISO 13628-2:2006/AC:2009 | PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 2: UNBONDED FLEXIBLE PIPE SYSTEMS FOR SUBSEA AND MARINE APPLICATIONS |
| BS EN 843-4:2005 | Advanced technical ceramics. Mechanical properties of monolithic ceramics at room temperature Vickers, Knoop and Rockwell superficial hardness |
| DIN EN 843-4:2005-08 | Advanced technical ceramics - Mechanical properties of monolithic ceramics at room temperature - Part 4: Vickers, Knoop and Rockwell superficial hardness |
| ASME B107.500 : 2010 | PLIERS |
| ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
| ASTM E 177 : 2014 : REDLINE | Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods |
| ASTM E 7 : 2017 : REDLINE | Standard Terminology Relating to Metallography |
| ASTM C 1327 : 2015 : REDLINE | TEST METHOD FOR VICKERS INDENTATION HARDNESS OF ADVANCED CERAMICS |
| ASTM E 2587 : 2016 : REDLINE | Standard Practice for Use of Control Charts in Statistical Process Control |
| ASTM E 2554 : 2013-05 | PRACTICE FOR ESTIMATING AND MONITORING THE UNCERTAINTY OF TEST RESULTS OF A TEST METHOD USING CONTROL CHART TECHNIQUES |
| ASTM E 92 : 2017 : REDLINE | Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials |
US$108.00
Excluding Tax where applicable
USD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.