ASTM E 563 : 2011 : R2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
08-23-2022
English
05-11-2016
CONTAINED IN VOL. 14.03, 2016 Describes a method for preparing, maintaining, and using a temperature reference bath of a mixture of shaved ice and water, saturated with air at a pressure of 101 325 Pa (1 atm).
1.1This practice covers a method of preparing, maintaining, and using a temperature reference bath of a mixture of shaved ice and water, saturated with air at a pressure of 101 325 Pa (1 atm).
1.2An industrial practice for relating values referenced to the ice point and to the water triple point on the ITS-90 is included.
1.3Methods to promote uniformity of bath temperature by mechanical stirring or agitation are not described in detail.
1.4Methods of approximating the ice point, as by thermostatically-controlled refrigeration, are not covered by this practice.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| Committee |
E 20
|
| DocumentType |
Standard Practice
|
| Pages |
4
|
| ProductNote |
Reconfirmed 2016
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM E 2730 : 2022 | Standard Guide for Calibration and Use of Thermocouple Reference Junction Probes in Evaluation of Electronic Reference Junction Compensation Circuits |
| ASTM D 2162 : 2021 | Standard Practice for Basic Calibration of Master Viscometers and Viscosity Oil Standards |
| ASTM E 2877 : 2012 : R2019 | Standard Guide for Digital Contact Thermometers |
| ASTM D 7552 : 2009 : R2014 | Standard Test Method for Determining the Complex Shear Modulus (G*) Of Bituminous Mixtures Using Dynamic Shear Rheometer |
| ASTM E 452 : 2002 : R2018 | Standard Test Method for Calibration of Refractory Metal Thermocouples Using a Radiation Thermometer |
| ASTM D 6821 : 2020 : REV A | Standard Test Method for Low Temperature Viscosity of Drive Line Lubricants in a Constant Shear Stress Viscometer |
| ASTM D 7962 : 2021 | Standard Practice for Determination of Minimum Immersion Depth and Assessment of Temperature Sensor Measurement Drift |
| ASTM E 644 : 2011(R2019) | Standard Test Methods for Testing Industrial Resistance Thermometers |
| ASTM D 4693 : 2007 : R2021 | Standard Test Method for Low-Temperature Torque of Grease-Lubricated Wheel Bearings |
| ASTM E 2820 : 2013 : R2019 | Standard Test Method for Evaluating Thermal EMF Properties of Base-Metal Thermocouple Connectors |
| ASTM D 4684 : 2020 : REV A | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature |
| ASTM D 5/D5M : 2020 | Standard Test Method for Penetration of Bituminous Materials |
| ASTM D 445 : 2021 : EDT 1 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM E 220 : 2019 | Standard Test Method for Calibration of Thermocouples By Comparison Techniques |
| ASTM D 70/D70M : 2021 | Standard Test Method for Specific Gravity and Density of Semi-Solid Asphalt Binder (Pycnometer Method) |
| ASTM E 601 : 2020 | Standard Guide for Measuring Electromotive Force (EMF) Stability of Base-Metal Thermoelement Materials With Time in Air |
| ASTM D 2532 : 2017 | Standard Test Method for Viscosity and Viscosity Change After Standing at Low Temperature of Aircraft Turbine Lubricants |
| ASTM E 2251 : 2014 : R2021 | Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids |
| ASTM D 8164 : 2021 | Standard Guide for Digital Contact Thermometers for Petroleum Products, Liquid Fuels, and Lubricant Testing |
| ASTM E 2846 : 2020 | Standard Guide for Thermocouple Verification |
| ASTM E 1 : 2014 : R2020 | Standard Specification for ASTM Liquid-in-Glass Thermometers |
| ASTM E 207 : 2021 | Standard Test Method for Thermal EMF Test of Single Thermoelement Materials by Comparison With Reference Thermoelement of Similar EMF-Temperature Properties |
| ASTM D 6896 : 2020 : REV A | Standard Test Method for Determination of Yield Stress and Apparent Viscosity of Used Engine Oils at Low Temperature |
| ASTM E 2593 : 2017 | Standard Guide for Accuracy Verification of Industrial Platinum Resistance Thermometers |
| ASTM D 61 : 2015 : R2019 | Standard Test Method for Softening Point of Pitches (Cube-in-Water Method) |
| ASTM D 1754/D1754M : 2020 | Standard Test Method for Effects of Heat and Air on Asphaltic Materials (Thin-Film Oven Test) |
| ASTM D 7175 : 2015 | Standard Test Method for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer |
| ASTM D 3829 : 2020 : REV A | Standard Test Method for Predicting the Borderline Pumping Temperature of Engine Oil |
| ASTM E 879 : 2020 | Standard Specification for Thermistor Sensors for General Purpose and Laboratory Temperature Measurements |
| ASTM D 6703 : 2019 | Standard Test Method for Automated Heithaus Titrimetry |
| ASTM D 7279 : 2020 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids by Automated Houillon Viscometer |
| ASTM D 2726/D2726M : 2021 | Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Asphalt Mixtures |
| ASTM D 8278 : 2020 | Standard Specification for Digital Contact Thermometers for Test Methods Measuring Flow Properties of Fuels and Lubricants |
| ASTM E 1594 : 2011 | Standard Guide for Expression of Temperature |
| ASTM E 344 : 2018 | Terminology Relating to Thermometry and Hydrometry |
| ASTM E 1594 : 2016 : REDLINE | Standard Guide for Expression of Temperature |
| ASTM E 344 : 2001 : REV A | Terminology Relating to Thermometry and Hydrometry |
| ASTM D 1193 : 1977 : R1983 : EDT 1 | Standard Specification for Reagent Water |
| ASTM D 1193 : 2006 : R2011 | Standard Specification for Reagent Water |
| ASTM E 1594 : 1999 | Standard Guide for Expression of Temperature |
| ASTM D 1193 : 1991 | Standard Specification for Reagent Water |
| ASTM E 344 : 2016-12 | TERMINOLOGY RELATING TO THERMOMETRY AND HYDROMETRY |
| ASTM E 1594 : 2016 | Standard Guide for Expression of Temperature |
| ASTM E 1594 : 2022 | Standard Guide for Expression of Temperature |
| ASTM D 1193 : 1970 | Standard Specification For Reagent Water |
| ASTM D 1193 : 2006 | Standard Specification for Reagent Water |
| ASTM D 1193 : 1999 | Standard Specification for Reagent Water |
| ASTM E 1594 : 2006 | Standard Guide for Expression of Temperature |
| ASTM D 1193 : 2006 : R2018 | Standard Specification for Reagent Water |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.