• There are no items in your cart

ASTM F 1498 : 2008 : R2012 : EDT 1

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Taper Pipe Threads 60° for Thermoplastic Pipe and Fittings
Available format(s)

Hardcopy , PDF

Superseded date

11-17-2020

Language(s)

English

Published date

11-08-2012

CONTAINED IN VOL. 08.04, 2018 Describes requirements for dimensions and gaging of taper pipe threads used on threaded plastic pipe and fittings.

1.1 This specification establishes requirements for dimensions and gaging of taper pipe threads used on threaded plastic pipe and fittings.

1.2 Threads meeting this specification shall only be used on those plastic materials deemed suitable by the manufacturer.

1.3 Specialty threads or threads not requiring a leak-tight joint are not covered in this specification.

Note 1The terms “wrench makeup” and “wrench tight” are standard terminology for tightness and do not imply using a pipe wrench or other tools which would damage plastic pipe and fittings. The terms “hand-tight” and “hand-tight engagement” refer only to thread gaging (not pipe and fitting connections) and is the definition of the L1 gage length.

1.4 Thread Designations—The type of pipe threads included in this specification are designated by specifying in sequence the nominal pipe size, number of threads per inch, and the thread series symbols as follows in accordance with ANSI/ASME B 1.20.1: 3/8-18 NPT. For left-hand threads add LH to the end of the designation, otherwise right-hand threads will be understood. For example: 3/8-18 NPT-LH.

1.4.1 Each of these letters in the symbol has a definite significance as follows:

N

=

National (American Standard)

P

=

Pipe

T

=

Taper


1.5 The values stated in inch-pound units are to be regarded as the standard. No other units of measurement are included in this standard.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see 7.2.1 and 8.3.

Committee
F 17
DocumentType
Standard
Pages
13
ProductNote
Reconfirmed EDT 1
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM F 2735 : 2018 Standard Specification for Plastic Insert Fittings For SDR9 Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing
ASTM D 2467 : 2015 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80
ASTM F 437 : 2015 Standard Specification for Threaded Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80
ASTM F 438 : 2017 Standard Specification for Socket-Type Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 40
ASTM D 2661 : 2014 : EDT 1 Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings
ASTM D 2466 : 2017 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40
ASTM F 2159 : 2019 Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring, or Alternate Stainless Steel Clamps for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing
ASTM D 3311 : 2017 Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns
ASTM F 439 : 2013 Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80
ASTM F 628 : 2012 : EDT 3 Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe With a Cellular Core (Withdrawn 2021)
ASTM F 409 : 2017 Standard Specification for Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings
ASTM F 1970 : 2019 Standard Specification for Special Engineered Fittings, Appurtenances or Valves for use in Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Systems
ASTM F 2390 : 2012 : R2017 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent (DWV) Pipe and Fittings Having Post-Industrial Recycle Content
ASTM F 1673 : 2010 : R2016 Standard Specification for Polyvinylidene Fluoride (PVDF) Corrosive Waste Drainage Systems
ASTM D 2464 : 2015 Standard Specification for Threaded Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80
ASTM F 1901 : 2016 Standard Specification for Polyethylene (PE) Pipe and Fittings for Roof Drain Systems
ASTM D 2665 : 2014 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
ASTM F 3371 : 2019 Standard Specification for Polyolefin Pipe and Fittings for Drainage, Waste, and Vent Applications
ASTM D 2122 : 2016 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 2609 : 2015 Standard Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe
ASTM D 2846/D2846M : 2019 : REV A Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Hot- and Cold-Water Distribution Systems
ASTM D 2949 : 2018 Standard Specification for 3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
ASTM F 2135 : 2001 : R2017 : EDT 1 Standard Specification for Molded Drain, Waste, and Vent (DWV) Short-Pattern Plastic Fittings
ASTM F 645 : 2018 : REV B Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems
ASTM D 2749 : 2013 Standard Symbols for Dimensions of Plastic Pipe Fittings (Withdrawn 2022)
ASTM F 1412 : 2016 Standard Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems

ASTM D 1600 : 1999 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM E 177 : 2014 : REDLINE Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods
ASTM D 1600 : 2007 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 1600 : 2013 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 1600 : 2014 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 1600 : 2008 Standard Terminology for Abbreviated Terms Relating to Plastics
ASME B1.20.1 : 2013(R2018) PIPE THREADS, GENERAL PURPOSE (INCH)
ASTM D 1600 : 2018 Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)

View more information
US$83.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.