• There are no items in your cart

ASTM F 3125/F3125M : 2018

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for High Strength Structural Bolts and Assemblies, Steel and Alloy Steel, Heat Treated, Inch Dimensions 120 ksi and 150 ksi Minimum Tensile Strength, and Metric Dimensions 830 MPa and 1040 MPa Minimum Tensile Strength
Available format(s)

Hardcopy , PDF

Superseded date

08-03-2020

Language(s)

English

Published date

12-01-2018

This specification covers chemical, physical and mechanical requirements for quenched and tempered bolts manufactured from steel and alloy steel, in inch and metric dimensions, in two strength grades, two types and two styles.

1.1This specification covers chemical, physical and mechanical requirements for quenched and tempered bolts manufactured from steel and alloy steel, in inch and metric dimensions, in two strength grades, two types and two styles.

1.1.1This specification is a consolidation and replacement of six ASTM standards, including; A325, A325M, A490, A490M, F1852 and F2280.

1.1.2This consolidated standard is to ensure alignment between standards with the same intended end use and to simplify the use and maintenance of structural bolt specifications.

1.2Intended Use:

1.2.1Bolts manufactured under this specification are intended for use in structural connections covered in the Specification for Structural Joints Using High-Strength Bolts, as approved by the Research Council on Structural Connections.

1.2.2Bolts in this specification are furnished in sizes from 1/2to 1-1/2in. inclusive and from M12 to M36 inclusive.

1.3Classification, Table 1:

1.3.1Bolts are designated by grade, which indicates inch or metric strength and style.

1.3.2Bolts are designated by type denoting raw material chemical composition.

1.3.3Bolts are designated by style denoting Heavy Hex bolts or “Twist-Off” Style assemblies.

1.4Terms used in this specification are defined in F1789.

1.5Units—The values stated in either SI units or inch pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.6Table footnotes are requirements. Notes are advisory.

1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
F 16
DocumentType
Standard
Pages
13
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM F 1940 : 2007 : REV A : R2014 Standard Test Method for Process Control Verification to Prevent Hydrogen Embrittlement in Plated or Coated Fasteners
ASTM F 1789 : 2014 : REV A Standard Terminology for F16 Mechanical Fasteners
ASTM F 1789 : 2016 Standard Terminology for F16 Mechanical Fasteners
ASTM F 1470 : 2012 Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
ASTM F 2328 : 2005 : R2011 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs
ASTM F 1789 : 2017 Standard Terminology for F16 Mechanical Fasteners
ASTM F 2329 : 2005 Standard Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners
ASTM F 2329 : 2011 Standard Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners
ASTM F 1789 : 2008 Standard Terminology for F16 Mechanical Fasteners
ASTM F 1789 : 2006 : REV A Standard Terminology for F16 Mechanical Fasteners
ASTM F 1789 : 2001 : REV A Standard Terminology of F16 Mechanical Fasteners
ASTM F 1470 : 2002 Standard Guide for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
ASTM F 1789 : 2017 : REV A Standard Terminology for F16 Mechanical Fasteners
ASTM F 1789 : 2012 : REV A Standard Terminology for F16 Mechanical Fasteners
ASTM F 1789 : 2001 : REV B Standard Terminology of F16 Mechanical Fasteners
ASTM F 1789 : 2005 : REV C Standard Terminology for F16 Mechanical Fasteners
ASTM F 1470 : 2009 Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
ASTM F 1789 : 2003 : REV A Standard Terminology for F16 Mechanical Fasteners
ASTM F 1789 : 2008 : REV B Standard Terminology for F16 Mechanical Fasteners
ASTM F 1789 : 2006 : REV B Standard Terminology for F16 Mechanical Fasteners
ASTM F 1789 : 2014 Standard Terminology for F16 Mechanical Fasteners
ASTM F 2660 : 2013 Standard Test Method for Qualifying Coatings for Use on A490 Structural Bolts Relative to Environmental Hydrogen Embrittlement
ASTM F 1789 : 2002 : REV A Standard Terminology of F16 Mechanical Fasteners
ASTM F 1789 : 2009 : REV A Standard Terminology for F16 Mechanical Fasteners
ASTM F 1789 : 2006 : REV C Standard Terminology for F16 Mechanical Fasteners
ASTM F 1789 : 2004 : REV B Standard Terminology for F16 Mechanical Fasteners
ASTM F 2329 : 2005 : R2011 Standard Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners
ASTM F 2328M : 2004 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs [Metric]
ASTM F 1789 : 2007 : REV C Standard Terminology for F16 Mechanical Fasteners
ASTM F 2328M : 2006 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs [Metric]
ASTM F 1789 : 2007 : REV A Standard Terminology for F16 Mechanical Fasteners
ASTM F 1789 : 2008 : REV C Standard Terminology for F16 Mechanical Fasteners
ASTM F 2328M : 2007 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs [Metric]
ASTM F 1789 : 2015 Standard Terminology for F16 Mechanical Fasteners
ASTM F 2328M : 2017 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts (Metric)
ASTM F 2328M : 2007 : R2014 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs (Metric)
ASTM F 1789 : 2002 : REV B Standard Terminology of F16 Mechanical Fasteners
ASTM F 2833 : 2011 Standard Specification for Corrosion Protective Fastener Coatings with Zinc Rich Base Coat and Aluminum Organic/Inorganic Type
ASTM F 1789 : 2010 : REV A Standard Terminology for F16 Mechanical Fasteners
ASTM F 2833 : 2011 : R2017 Standard Specification for Corrosion Protective Fastener Coatings with Zinc Rich Base Coat and Aluminum Organic/Inorganic Type
ASTM F 1789 : 2012 Standard Terminology for F16 Mechanical Fasteners
ASTM F 1789 : 2005 : REV D Standard Terminology for F16 Mechanical Fasteners
ASTM F 2328 : 2017 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts
ASTM F 1940 : 2001 Standard Test Method for Process Control Verification to Prevent Hydrogen Embrittlement in Plated or Coated Fasteners
ASTM F 2328 : 2004 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs
ASTM F 2329 : 2013 Standard Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners
ASTM F 2328 : 2014 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts
ASTM F 1789 : 2010 : REV B Standard Terminology for F16 Mechanical Fasteners
ASTM F 1789 : 2010 : REV A : EDT 1 Standard Terminology for F16 Mechanical Fasteners
ASTM F 1789 : 2015 : REV A Standard Terminology for F16 Mechanical Fasteners
ASTM F 1940 : 2007 : REV A Standard Test Method for Process Control Verification to Prevent Hydrogen Embrittlement in Plated or Coated Fasteners
ASTM F 2328M : 2005 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs [Metric]
ASTM F 1789 : 2000 : REV A Standard Terminology of F16 Mechanical Fasteners
ASTM F 1470 : 2018 Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
ASTM F 2328 : 2005 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs
ASTM F 1789 : 2007 : REV B Standard Terminology for F16 Mechanical Fasteners
ASTM F 1789 : 2011 : REV B Standard Terminology for F16 Mechanical Fasteners
ASTM F 1470 : 2001 Standard Guide for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
ASTM F 1789 : 2004 : REV A Standard Terminology for F16 Mechanical Fasteners
ASTM F 2660 : 2012 Standard Test Method for Qualifying Coatings for Use on A490 Structural Bolts Relative to Hydrogen Embrittlement
ASTM F 1789 : 2005 : REV A Standard Terminology for F16 Mechanical Fasteners
ASTM F 1470 : 2019 Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
ASTM F 1789 : 2008 : REV D Standard Terminology for F16 Mechanical Fasteners
ASTM F 1789 : 2007 Standard Terminology for F16 Mechanical Fasteners
ASTM F 1789 : 2008 : REV A Standard Terminology for F16 Mechanical Fasteners
ASTM F 1940 : 2007 : REV A : R2019 Standard Test Method for Process Control Verification to Prevent Hydrogen Embrittlement in Plated or Coated Fasteners
ASTM F 1789 : 2011 : REV A Standard Terminology for F16 Mechanical Fasteners
ASTM F 2328M : 2007 : R2013 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs (Metric)
ASTM F 1940 : 2007 Standard Test Method for Process Control Verification to Prevent Hydrogen Embrittlement in Plated or Coated Fasteners
ASTM F 1789 : 2005 : REV B Standard Terminology for F16 Mechanical Fasteners
ASTM F 2328M : 2014 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts (Metric)
ASTM F 1789 : 2002 Standard Terminology of F16 Mechanical Fasteners
ASTM F 1940 : 1999 Standard Test Method for Process Control Verification to Prevent Hydrogen Embrittlement in Plated or Coated Fasteners

View more information
US$83.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.