Standard Specification for Carbon and Alloy Steel Metric Rivets

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

05-27-2022

Publisher

American Society for Testing and Materials

1.1This specification covers chemical and mechanical requirements for nine property classes of carbon and alloy steel metric rivets in nominal diameters M01 through M36 suited for use in general engineering applications.

1.2This specification does not cover dimensional requirements for rivets of any property class. When referencing this specification for procurement purposes, it is mandatory that size, type, style, and any special dimensions of the product be additionally specified.

1.2.1In case of any conflict in requirements, the requirements of the individual product specification shall take precedence over those of this general specification.

1.2.2The purchaser may specify additional requirements which do not negate any of the provisions of this general specification or of the individual product specification. Such additional requirements, the acceptance of which are subject to negotiation with the supplier, must be included in the order information (see Section 3).

1.3When agreed on by the purchaser, Class 5.8 fasteners may be supplied when either Classes 4.6 or 4.8 are ordered; Class 4.8 may be supplied when Class 4.6 is ordered;

1.4The product size range for which each property class is applicable is given in Table 1 on chemical composition requirements, and the mechanical requirements table (see Table 2).

1.5Appendix X1 explains the significance of the property class designation numerals.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee	F 16
DocumentType	Standard
Pages	4
PublisherName	American Society for Testing and Materials
Status	Current

ASTM F 1470 : 2012	Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
ASTM F 606/F606M : 2019	Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
ASTM F 1470 : 2002	Standard Guide for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
ASTM F 1470 : 2009	Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
ASTM B 695 : 2004 : R2016	Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel
ASTM A 153/A153M : 2016 : REV A	Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware
ASTM A 751 : 2021	Standard Test Methods and Practices for Chemical Analysis of Steel Products
ASTM F 788/F788M : 2020 : EDT 1	Standard Specification for Surface Discontinuities of Bolts, Screws, Studs, and Rivets, Inch and Metric Series
ASTM B 695 : 2021	Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel
ASTM F 788/F788M : 1997	Standard Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series
ASTM A 751 : 2020	Standard Test Methods and Practices for Chemical Analysis of Steel Products
ASTM F 1470 : 2018	Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
ASTM F 1470 : 2001	Standard Guide for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
ASTM A 153/A153M : 2023	Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware
ASTM F 1470 : 2019	Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
ASTM F 1470 : 2024	Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
ASTM F 606/F606M : 2021	Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets