• There are no items in your cart

ASTM F 1924 : 2019

Current
Current

The latest, up-to-date edition.

Standard Specification for Plastic Mechanical Fittings for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

08-01-2019

This specification describes requirements and test methods for the qualification of plastic bodied mechanical fittings for use with outside diameter controlled polyethylene (PE) gas distribution pipe, nominal 2 pipe size (IPS) and smaller complying with Specification D2513.

1.1This specification describes requirements and test methods for the qualification of plastic bodied mechanical fittings for use with outside diameter controlled polyethylene (PE) gas distribution pipe, nominal 2 pipe size (IPS) and smaller complying with Specification D2513. In addition, it specifies general requirements of the material from which these fittings are made.

1.2The test methods described in this specification are not intended to be used as routine quality control tests.

1.3This specification covers the types of mechanical fittings described in 3.2.

1.4The text of this specification references notes and footnotes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification.

1.5The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.6The following safety hazards caveat pertains only to the test method portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
F 17
DocumentType
Standard
Pages
5
ProductNote
THIS STANDARD ALSO REFERS TO :CFR, Title 49, Part 192
PublisherName
American Society for Testing and Materials
Status
Current
Supersedes

ASTM F 412 : 2019 Standard Terminology Relating to Plastic Piping Systems

ASTM F 2897 : 2023 : REV A Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances)
ASTM F 412 : 2020 : REV A Standard Terminology Relating to Plastic Piping Systems
ASTM D 1598 : 2015 : REV A Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM F 412 : 2021 Standard Terminology Relating to Plastic Piping Systems
ASTM D 1598 : 2023 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM F 1588 : 1996(R2019) Standard Test Method for Constant Tensile Load Joint Test (CTLJT)
ASTM D 2837 : 2021 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
ASTM F 2897 : 2021 Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances)
ASTM D 1598 : 1997 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM F 2897 : 2015 : REV A Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances)
ASTM D 2513 : 2019 Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
ASTM D 2837 : 2022 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
ASTM D 638 : 2014 Standard Test Method for Tensile Properties of Plastics
ASTM D 1600 : 2018 Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
ASTM F 2897 : 2023 Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances)
ASTM F 412 : 2023 Standard Terminology Relating to Plastic Piping Systems
ASTM D 1598 : 2021 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM D 2513 : 2018 : REV A Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
ASTM F 1588 : 1996 : R2015 Standard Test Method for Constant Tensile Load Joint Test (CTLJT)
ASTM D 638 : 2022 Standard Test Method for Tensile Properties of Plastics
ASTM D 2837 : 2013 : EDT 1 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products

View more information
US$63.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.