• There are no items in your cart

ASTM G 99 : 2017 : REDLINE

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Wear Testing with a Pin-on-Disk Apparatus
Available format(s)

PDF

Superseded date

11-20-2023

Language(s)

English

Published date

01-20-2017

CONTAINED IN VOL. 03.02, 2017 Defines a laboratory procedure for determining the wear of materials during sliding using a pin-on-disk apparatus.

1.1This test method covers a laboratory procedure for determining the wear of materials during sliding using a pin-on-disk apparatus. Materials are tested in pairs under nominally non-abrasive conditions. The principal areas of experimental attention in using this type of apparatus to measure wear are described. The coefficient of friction may also be determined.

1.2This test method standard uses a specific set of test parameters (load, sliding speed, materials, etc.) that were then used in an interlaboratory study (ILS), the results of which are given here (Tables 1 and 2). (This satisfies the ASTM form in that “The directions for performing the test should include all of the essential details as to apparatus, test specimen, procedure, and calculations needed to achieve satisfactory precision and bias.”) Any user should report that they “followed the requirements of ASTM G99,” where that is true.

1.3Now it is often found in practice that users may follow all instructions given here, but choose other test parameters, such as load, speed, materials, environment, etc., and thereby obtain different test results. Such a use of this standard is encouraged as a means to improve wear testing methodology. However, it must be clearly stated in any report that, while the directions and protocol in Test Method G99 were followed (if true), the choices of test parameters were different from Test Method G99 values, and the test results were therefore also different from the Test Method G99 results. This use should be described as having “followed the procedure of ASTM G99.” All test parameters that were used in such case must be stated.

1.4The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
G 02
DocumentType
Redline
Pages
6
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

08/30170504 DC : DRAFT AUG 2008 BS EN 1071-13 - ADVANCED TECHNICAL CERAMICS - METHODS OF TEST FOR CERAMIC COATINGS - PART 13: DETERMINATION OF WEAR RATE BY THE PIN-ON-DISK METHOD
15/30324532 DC : 0 BS ISO 20808 - FINE CERAMICS (ADVANCED CERAMICS, ADVANCED TECHNICAL CERAMICS) - DETERMINATION OF FRICTION AND WEAR CHARACTERISTICS OF MONOLITHIC CERAMICS BY BALL-ON-DISC METHOD
I.S. EN 1071-13:2010 ADVANCED TECHNICAL CERAMICS - METHODS OF TEST FOR CERAMIC COATINGS - PART 13: DETERMINATION OF WEAR RATE BY THE PIN-ON-DISK METHOD
BS EN 1071-13:2010 Advanced technical ceramics. Methods of test for ceramic coatings Determination of wear rate by the pin-on-disk method
BS ISO 18535:2016 Diamond-like carbon films. Determination of friction and wear characteristics of diamond-like carbon films by ball-on-disc method
DIN EN 1071-13:2010-07 Advanced technical ceramics - Methods of test for ceramic coatings - Part 13: Determination of wear rate by the pin-on-disk method
ASTM G 118 : 2002 Standard Guide for Recommended Format of Wear Test Data Suitable for Databases
ASTM G 133 : 2005 : R2016 Standard Test Method for Linearly Reciprocating Ball-on-Flat Sliding Wear
UNE 112086:2016 Tribocorrosion testing procedure for passivating materials.
ISO/TR 13393:2009 Welding consumables Hardfacing classification Microstructures
ASTM G 115 : 2010 : R2013 Standard Guide for Measuring and Reporting Friction Coefficients
VDI 2083 Blatt 17:2013-06 Cleanroom technology - Compatibility of materials with the required cleanliness
VDI 2083 Blatt 9.1:2006-12 Clean room technology - Compatibility with required cleanliness and surface cleanliness
VDI 3823 Blatt 4:2006-11 Vacuum coating quality assurance - Testing of vacuum coated plastics
ASTM G 132 : 1996 Standard Test Method for Pin Abrasion Testing
15/30279088 DC : 0 BS ISO 18535 - DIAMOND-LIKE CARBON FILMS - DETERMINATION OF FRICTION AND WEAR CHARACTERISTICS OF DIAMOND-LIKE CARBON FILMS BY BALL-ON-DISC METHOD
ASTM G 204 : 2015 : REDLINE Standard Test Method for Damage to Contacting Solid Surfaces under Fretting Conditions
ASTM D 7027 : 2013 : REDLINE Standard Test Method for Evaluation of Scratch Resistance of Polymeric Coatings and Plastics Using an Instrumented Scratch Machine
ASTM G 132 : 1996 : R2007 Standard Test Method for Pin Abrasion Testing
ISO 20808:2016 Fine ceramics (advanced ceramics, advanced technical ceramics) Determination of friction and wear characteristics of monolithic ceramics by ball-on-disc method
UNI EN 1071-13 : 2010 ADVANCED TECHNICAL CERAMICS - METHODS OF TEST FOR CERAMIC COATINGS - PART 13: DETERMINATION OF WEAR RATE BY THE PIN- ON-DISK METHOD
ASTM G 133 : 2005 : R2010 Standard Test Method for Linearly Reciprocating Ball-on-Flat Sliding Wear
BS ISO 20808:2016 Fine ceramics (advanced ceramics, advanced technical ceramics). Determination of friction and wear characteristics of monolithic ceramics by ball-on-disc method
ASTM G 133 : 2005 : EDT 1 Standard Test Method for Linearly Reciprocating Ball-on-Flat Sliding Wear
ASTM G 133 : 2005 Standard Test Method for Linearly Reciprocating Ball-on-Flat Sliding Wear
ASTM G 118 : 2002 : R2015 Standard Guide for Recommended Format of Wear Test Data Suitable for Databases (Withdrawn 2016)
ASTM G 132 : 1996 : R2013 Standard Test Method for Pin Abrasion Testing
ISO 18535:2016 Diamond-like carbon films Determination of friction and wear characteristics of diamond-like carbon films by ball-on-disc method
ASTM G 118 : 2002 : R2007 Standard Guide for Recommended Format of Wear Test Data Suitable for Databases
ASTM G 190 : 2015 Standard Guide for Developing and Selecting Wear Tests (Withdrawn 2021)
ASTM G 115 : 2010 Standard Guide for Measuring and Reporting Friction Coefficients
ASTM G 132 : 1996 : R2018 Standard Test Method for Pin Abrasion Testing
ASTM G 132 : 1996 : R2001 Standard Test Method for Pin Abrasion Testing
EN 1071-13:2010 Advanced technical ceramics - Methods of test for ceramic coatings - Part 13: Determination of wear rate by the pin-on-disk method

DIN 50324:1992-07 TRIBOLOGY; TESTING OF FRICTION AND WEAR MODEL TEST FOR SLIDING FRICTION OF SOLIDS (BALL ON DISC SYSTEM)

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.