• There are no items in your cart

AWWA C516 : 2014

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

LARGE-DIAMETER RUBBER-SEATED BUTTERFLY VALVES, SIZES 78 IN. (2,000 MM) AND LARGER
Available format(s)

Hardcopy , PDF

Superseded date

08-17-2021

Language(s)

English

Published date

01-01-2014

Foreword
I Introduction
II Special Issues
III Use of This Standard
IV Major Revisions
V Comments
Standard
1 General
2 References
3 Definitions
4 Requirements
5 Verification
6 Delivery
Appendix
A - Installation, Operation, and
    Maintenance of Large-Diameter
    Butterfly Valves

Gives minimum requirements for rubber-seated butterfly valve assemblies that are 78 in. (2,000 mm) diameter and larger with flanged ends suitable for fresh and reclaimed water having a pH range from 6-12 and a temperature range from 33 DEGREES-125 DEGREES F (0.6 DEGREES-52 DEGREES C) and suitable for a maximum steady-state fluid working pressure of 250 psig (1,724 kPa [gauge]), a maximum steady-state differential pressure of 250 psi (1,724 kPa), and a maximum full-open fluid velocity of 16 ft/sec (4.9 m/sec) based on nominal valve size.

DocumentType
Revision
ISBN
9781625761057
Pages
44
PublisherName
American Water Works Association
Status
Superseded
SupersededBy
Supersedes

BS EN 593:2017 Industrial valves. Metallic butterfly valves for general purposes
AWWA M44 : 2016 DISTRIBUTION VALVES: SELECTION, INSTALLATION, FIELD TESTING, AND MAINTENANCE
I.S. EN 593:2017 INDUSTRIAL VALVES - METALLIC BUTTERFLY VALVES FOR GENERAL PURPOSES
AWWA M49 : 2017 BUTTERFLY VALVES: TORQUE, HEAD LOSS, AND CAVITATION ANALYSIS
16/30339483 DC : 0 BS EN 593 - INDUSTRIAL VALVES - METALLIC BUTTERFLY VALVES FOR GENERAL PURPOSES
PREN 593 : DRAFT 2016 INDUSTRIAL VALVES - METALLIC BUTTERFLY VALVES FOR GENERAL PURPOSES
EN 593:2017 Industrial valves - Metallic butterfly valves for general purposes

AWWA M49 : 2012 BUTTERFLY VALVES: TORQUE, HEAD LOSS, AND CAVITATION ANALYSIS
AWWA C541 : 2016 HYDRAULIC AND PNEUMATIC CYLINDER AND VANE-TYPE ACTUATORS FOR VALVES AND SLIDE GATES
NSF 61 : 2016 DRINKING WATER SYSTEM COMPONENTS - HEALTH EFFECTS
AWWA C207 : 2013 STEEL PIPE FLANGES FOR WATERWORKS SERVICE, SIZES 4 IN. THROUGH 144 IN. (100 MM THROUGH 3,600 MM)
ASTM B 154 : 2016 : REDLINE Standard Test Method for Mercurous Nitrate Test for Copper Alloys
AWWA C550 : 2017 PROTECTIVE INTERIOR COATINGS FOR VALVES AND HYDRANTS
AWS A5.4 : 92(R2000) STAINLESS STEEL ELECTRODES FOR SHIELDED METAL ARC WELDING, SPECIFICATION FOR
ASTM D 1141 : 1998 : EDT 1 Standard Practice for the Preparation of Substitute Ocean Water
ASTM D 1149 : 2016-02 TEST METHODS FOR RUBBER DETERIORATION - CRACKING IN AN OZONE CONTROLLED ENVIRONMENT
ASTM A 516/A516M : 2017 : REDLINE Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service
AWS A5.5 : 1996 SPECIFICATION FOR LOW ALLOY STEEL ELECTRODES FOR SHIELDED METAL ARC WELDING
AWS A5.1 : 91(R1999) SPECIFICATION FOR CARBON STEEL ELECTRODES FOR SHIELDED METAL ARC WELDING
AWWA C542 : 2016 ELECTRIC MOTOR ACTUATORS FOR VALVES AND SLIDE GATES
ASTM B 438 : 2017 : REDLINE Standard Specification for Bronze-Base Powder Metallurgy (PM) Bearings (Oil-Impregnated)
AWS A5.11 : 1990 NICKEL AND NICKEL ALLOY WELDING ELECTRODES FOR SHIELDED METAL ARC WELDING
ASTM E 709 : 2015 : REDLINE Standard Guide for Magnetic Particle Testing
AWS D1.1 : 2000 STRUCTURAL WELDING CODE - STEEL
ASTM D 471 : 2016-02 TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS
NSF 372 : 2016 DRINKING WATER SYSTEM COMPONENTS - LEAD CONTENT

View more information
US$140.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.