Name: BIS IS 513 : 2008 AMD 2 2016
Brand: BIS

COLD REDUCED LOW CARBON STEEL SHEET AND STRIP

Published date

01-12-2013

Publisher

Bureau of Indian Standards

FOREWORD
1 SCOPE
2 REFERENCES
3 CLASSIFICATION OF GRADES
4 SUPPLY OF MATERIAL
5 MANUFACTURE
6 CHEMICAL COMPOSITION
7 MECHANICAL AND PHYSICAL PROPERTIES
8 SURFACE FINISH
9 FREEDOM FROM DEFECTS
10 DIMENSIONS AND TOLERANCES
11 SAMPLING FOR TESTS
12 MARKING
ANNEX A (Foreword) - CORRELATION OF OLD
AND NEW GRADES/DESIGNATIONS
ANNEX B (Clause 4.4.3 and 4.4.3.1) - STABILITY
TEST
ANNEX C (Foreword) - COMMITTEE COMPOSITION

Specifies the requirements of cold reduced low carbon steel sheets and strips for bending and drawing purpose and where the surface is of prime importance.

Committee	MTD 4
DevelopmentNote	Supersedes BIS IS 4030. (09/2008)
DocumentType	Standard
PublisherName	Bureau of Indian Standards
Status	Current
Supersedes	BIS IS 4030 : 1973

BIS IS 10864 : 2013	METAL JACKETED GASKETS FOR PIPE FLANGES AND HEAT EXCHANGER FLANGES - SPECIFICATION
BIS IS 1956-4 : 2013	GLOSSARY OF TERMS RELATING TO IRON AND STEEL - PART 4: FLAT PRODUCTS
BIS IS 16176 : 2014	RATCHET PIPE THREADER FOR TAPER PIPE THREADS (R-SERIES) - SPECIFICATION
BIS IS 1783-2 : 2014	DRUMS LARGE, FIXED ENDS - SPECIFICATION - PART 2: GRADE B DRUMS
BIS IS 950 : 2012	FUNCTIONAL REQUIREMENTS FOR WATER TENDER, TYPE B FOR FIRE BRIGADE USE
BIS IS 5244 : 2014 AMD 1 2015	SAFE DEPOSIT LOCKER CABINETS - SPECIFICATION
BIS IS 14246 : 2013	CONTINUOUSLY PRE-PAINTED GALVANIZED STEEL SHEETS AND COILS
BIS IS 15908 : 2011	SELECTION, INSTALLATION AND MAINTENANCE OF CONTROL AND INDICATING EQUIPMENTS FOR FIRE DETECTION AND ALARM SYSTEM - CODE OF PRACTICE
BIS IS 2932-1 : 2013 AMD 1 2015	ENAMEL, SYNTHETIC, EXTERIOR: (A) UNDERCOATING (B) FINISHING - SPECIFICATION
IS 13997 : 2014	DRUMS, LARGE OPEN TOP - SPECIFICATION
BIS IS 1239-1 : 2004 AMD 5 2017	STEEL TUBES, TUBULARS AND OTHER WROUGHT STEEL FITTINGS - SPECIFICATION - PART 1: STEEL TUBES
BIS IS 12933-2 : 2003 AMD 3 2013	SOLAR FLAT PLATE COLLECTOR - SPECIFICATION - PART 2: COMPONENTS
BIS IS 800 : 2007 AMD 1 2012	GENERAL CONSTRUCTION IN STEEL - CODE OF PRACTICE
BIS IS 629 : 2013	BICYCLE - HUB ASSEMBLY - SPECIFICATION
BIS IS 7142 : 1995(R2006)	WELDED LOW CARBON STEEL CYLINDERS FOR LOW PRESSURE LIQUEFIABLE GASES NOT EXCEEDING 5 LITRE WATER CAPACITY - SPECIFICATION
BIS IS 16074 : 2013	STEEL FLUSH DOOR SHUTTERS - SPECIFICATION
BIS IS 13152-1 : 2013	PORTABLE SOLID BIO-MASS COOKSTOVE (CHULHA) - SPECIFICATION
ISO 6932:2014	Cold-reduced carbon steel strip with a maximum carbon content of 0,25 %
BIS IS 3074 : 2013	STEEL TUBES FOR AUTOMOTIVE PURPOSES - SPECIFICATION
13/30280533 DC : 0	BS ISO 6932 - COLD-REDUCED CARBON STEEL STRIP WITH A MAXIMUM CARBON CONTENT OF 0,25%
BS ISO 6932:2014	Cold-reduced carbon steel strip with a maximum carbon content of 0,25 %
BIS IS 15961 : 2012 AMD 1 2016	HOT DIP ALUMINIUM-ZINC ALLOY METALLIC COATED STEEL STRIP AND SHEET (PLAIN)
BIS IS 11188-1 : 2014 AMD 1 2015	VAULT (STRONG ROOM) DOORS - PART 1: SPECIFICATION

ISO 6507-1:2005	Metallic materials Vickers hardness test Part 1: Test method
ISO 10275:2007	Metallic materials Sheet and strip Determination of tensile strain hardening exponent
BIS IS 1586 : 2000(R2006)	METHOD FOR ROCKWELL HARDNESS TEST FOR METALLIC MATERIAL (SCALES A-B-C-D-E-F-G-H-K 15N, 30N, 45N, 15T, 30T AND 45T)
ISO 6892:1998	Metallic materials Tensile testing at ambient temperature
BIS IS 10175-1 : 1993(R2003)	MECHANICAL TESTING OF METALS - MODIFIED ERICHSEN CUPPING TEST - SHEET AND STRIP PT 1 THICKNESS UPTO 2 MM
BIS IS 1501 : 2002	METHOD FOR VICKERS HARDNESS TEST FOR METALLIC MATERIALS
BIS IS 11999 : 2007(R2009)	METHOD FOR DETERMINATION OF PLASTIC STRAIN RATIO 'R' FOR STEEL SHEETS
BIS IS 1599 : 2012(R2017)	METALLIC MATERIALS - BEND TEST
BIS IS 15756 : 2007	METALLIC MATERIALS - SHEET AND STRIP - DETERMINATION OF TENSILE STRAIN HARDENING EXPONENT
BIS IS 1608 : 2005	METALLIC MATERIALS - TENSILE TESTING AT AMBIENT TEMPERATURE
BIS IS/ISO 16162 : 2012	CONTINUOUSLY COLD-ROLLED STEEL SHEET PRODUCTS - DIMENSIONAL AND SHAPE TOLERANCES
BIS IS 8910 : 2010	GENERAL TECHNICAL DELIVERY REQUIREMENTS FOR STEEL AND STEEL PRODUCTS