• There are no items in your cart

BS 7291-4:1990

Withdrawn
Withdrawn

A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

Thermoplastics pipes and associated fittings for hot and cold water for domestic purposes and heating installations in buildings Specification for chlorinated polyvinyl chloride (PVC-C) pipes and associated fittings and solvent cement
Available format(s)

Hardcopy , PDF

Withdrawn date

08-02-2013

Language(s)

English

Published date

05-31-1990

Committees responsible
Foreword
Specification
Section 1. General
1. Scope
2. Materials
3. Marking and associated information
Section 2. PVC-C pipes
4. Nominal sizes
5. Dimensions
6. Physical properties of PVC-C pipes
Section 3. Fittings for PVC-C pipes
7. Jointing
8. Classification and associated performance
     requirements for fittings for PVC-C pipes
9. Designation of sizes of fittings
10. Physical properties of fittings for PVC-C pipes
Section 4. Solvent cement
11. Materials
12. Film properties
13. Physical properties of solvent cement joints
14. Labelling and information
Appendices
A. Method of test for resistance to leaching of
     chlorides
B. Method of test for resistance to pull-out of
     assembled joints
C. Preparation of test joints
D. Method of test for film properties
E. Determination of shear strength
F. Method of test for resistance of jointed solvent
     cement to hydrostatic pressure at elevated
     temperature
G. Guidance on quality control testing
Tables
1. Dimensions of PVC-C pipe
2. Mass of striker upon impact (including any
     associated weights)
3. Pull-out test forces for joints of pipes in
     compliance with table 1 and/or associated fittings
4. Applicability of requirements and test methods
Figure
1. Solvent cement spreader
2. Jig arrangement for the shear strength test

Requirements and test conditions for chlorinated polyvinyl chloride materials and pipes of 12 mm to 63 mm outside diameter in metric sizes standardized for plastics pipes. It gives performance requirements for associated fittings and assemblies involving PVC-C pipes, including cemented joints.

Committee
PRI/88
DevelopmentNote
Supersedes 89/39234 DC. (09/2005) Inactive for the new design. (02/2009)
DocumentType
Standard
Pages
24
PublisherName
British Standards Institution
Status
Withdrawn

BS 7291-2:1990 Thermoplastics pipes and associated fittings for hot and cold water for domestic purposes and heating installations in buildings Specification for polybutylene (PB) pipes and associated fittings
BS 7291-3:1990 Thermoplastics pipes and associated fittings for hot and cold water for domestic purposes and heating installations in buildings Specification for crosslinked polyethylene (PE-X) pipes and associated fittings
BS 7291-1:1990 Thermoplastics pipes and associated fittings for hot and cold water for domestic purposes and heating installations in buildings General requirements
BS 6700:1997 Specification for design, installation, testing and maintenance of services supplying water for domestic use within buildings and their curtilages
BS 6700(2006) : 2006 DESIGN, INSTALLATION, TESTING AND MAINTENANCE OF SERVICES SUPPLYING WATER FOR DOMESTIC USE WITHIN BUILDINGS AND THEIR CURTILAGES - SPECIFICATION
BS DD251(2000) : 2000 SPRINKLER SYSTEMS FOR RESIDENTIAL AND DOMESTIC OCCUPANCIES - CODE OF PRACTICE
BS EN ISO 21003-3:2008 Multilayer piping systems for hot and cold water installations inside buildings Fittings
ISO 21003-3:2008 Multilayer piping systems for hot and cold water installations inside buildings — Part 3: Fittings
BS 5955-8:1990 Plastics pipework (thermoplastics materials) Specification for the installation of thermoplastics pipes and associated fittings for use in domestic hot and cold water services and heating systems
I.S. EN ISO 21003-3:2008 MULTILAYER PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS INSIDE BUILDINGS - PART 3: FITTINGS
EN ISO 21003-3:2008 Multilayer piping systems for hot and cold water installations inside buildings - Part 3: Fittings (ISO 21003-3:2008)

BS 871:1981 Specification for abrasive papers and cloths
BS 5214-2:1978 Specification for testing machines for rubbers and plastics Constant rate of force application machines
BS 2782-11:Method 1101A:1981 Methods of testing plastics. Thermoplastics pipes, fittings and valves Measurement of dimensions of pipes
BS 7291-3:1990 Thermoplastics pipes and associated fittings for hot and cold water for domestic purposes and heating installations in buildings Specification for crosslinked polyethylene (PE-X) pipes and associated fittings
BS 4346-1:1969 Joints and fittings for use with unplasticized PVC pressure pipes Injection moulded unplasticized PVC fittings for solvent welding for use with pressure pipes, including potable water supply
BS 4728:1971 Method for determination of the resistance to constant internal pressure of thermoplastics pipe
BS 2782-11.1106A(1983) : 1983(R1999) METHODS OF TESTING PLASTICS - THERMOPLASTICS PIPES, FITTINGS AND VALVES - ASSESSMENT OF PIGMENT DISPERSION IN POLYOLEFIN PIPES AND FITTINGS: MICROTOME METHOD
BS 2782-11:Method 1108A:1989 Methods of testing plastics. Thermoplastics pipes, fittings and valves True impact rate (TIR) boundaries of pipes
BS 2782-11 Method 1102A:1981 Methods of testing plastics. Thermoplastics pipes, fittings and valves Longitudinal reversion of pipes: immersion bath method
BS 5556:1978 Specification for general requirements for dimensions and pressure ratings for pipe of thermoplastics materials (metric series)
BS 7291-2:1990 Thermoplastics pipes and associated fittings for hot and cold water for domestic purposes and heating installations in buildings Specification for polybutylene (PB) pipes and associated fittings
BS 864:1953 Capillary and compression tube fittings of copper and copper alloy for use with copper tube complying with BS 659 and BS 1386.
BS 2782-11 Method 1103A:1982 Methods of testing plastics. Thermoplastics pipes, fittings and valves Stress relief test for injection moulded fittings: oven method
ISO 1043-1:2011 Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics
BS 5955-8:1990 Plastics pipework (thermoplastics materials) Specification for the installation of thermoplastics pipes and associated fittings for use in domestic hot and cold water services and heating systems
BS 7291-1:1990 Thermoplastics pipes and associated fittings for hot and cold water for domestic purposes and heating installations in buildings General requirements
BS 2782-11 Method 1102B:1981 Methods of testing plastics. Thermoplastics pipes, fittings and valves Longitudinal reversion of pipes: oven method

View more information
US$237.18
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.