BS EN 10225:2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
05-23-2019
English
07-31-2009
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Information to be supplied by the purchaser
4.1 General
4.2 Options
5 Dimensions, mass and tolerances
5.1 Dimensions and tolerances
5.2 Mass of steel
6 Classification and designation
6.1 Classification
6.2 Designation
7 Manufacturing process
7.1 Steel manufacturing process
7.2 Thickness limits and segregation control
7.3 Delivery condition
8 Requirements
8.1 General
8.2 Chemical composition
8.3 Mechanical properties
8.4 Technological properties
8.5 Surface condition and internal defects
9 Inspection and testing
9.1 General
9.2 Ex-mill supply
9.3 Merchant supply
9.4 Identification of cast
9.5 Delivery
10 Sampling
10.1 General
10.2 Frequency of testing
10.3 Preparation of samples and test pieces
10.4 Verification of chemical composition
11 Test methods
11.1 Chemical analysis
11.2 Mechanical tests
11.3 Non-destructive tests
11.4 Re-tests and re-submission for testing
12 Marking, bundling and protective coating
12.1 Die stamp and paint marking
12.2 Bundling
12.3 Colour coding
12.4 Protective coating
13 Options
Annex A (normative) - Location of test samples for tensile
and impact tests
Annex B (normative) - Location of tensile test piece when
two rolled surfaces cannot be retained
Annex C (normative when option 2 is specified by the purchaser) -
Details of manufacturing procedures to be supplied by the
manufacturer for steels of groups 2 and 3
Annex D (normative when option 16 is specified by the purchaser) -
Cold forming characteristics for steel plate of groups
2 and 3
Annex E (normative when option 18 is specified by the purchaser) -
Weldability testing for steels of groups 2 and 3 and
mechanical testing of butt welds
Annex F (normative when option 18 is specified by the purchaser) -
Weldability testing for steels of groups 2 and 3 -
Bead-on-plate
Annex G (normative when option 18 is specified by the purchaser) -
Weldability testing for steels of groups 2 and 3 -
Controlled thermal severity tests (CTS)
Bibliography
Describes requirements for weldable structural steels to be used in the fabrication of fixed offshore structures in the form of plates up to and including 150 mm thick.
This European Standard specifies requirements for weldable structural steels to be used in the fabrication of fixed offshore structures in the form of plates up to and including 150 mm thick. It also specifies sections up to 63 mm thick except for sections delivered in the as-rolled condition which are permitted up to 25 mm thick only. Seamless hollow sections up to and including 40 mm thick and high frequency electric resistance welded hollow sections up to and including 20 mm thick are specified. Greater thicknesses for sections and hollow sections may be agreed, provided the technical requirements of this European Standard are maintained. For plates the thickness limitations are: S355G2+N, S355G5+M, - up to and including 20 mm S355G3+N, S355G6+M - up to and including 40 mm S355G7+N, S355G8+N, S355G9+N, S355G10+N - up to and including 150 mm S355G7+M, S355G8+M, S355G9+M, S355G10+M - up to and including 100 mm S420G1+Q, S420G1+M, S420G2+Q, S420G2+M - up to and including 100 mm S460G1+Q, S460G1+M, S460G2+Q, S460G2+M - up to and including 100 mm The standard is applicable to steels for offshore structures, designed to operate in the offshore sector but not to steels supplied for the fabrication of subsea pipelines, risers, process equipment, process piping, and other utilities. It is primarily applicable to the North Sea Sector, but may also be applicable in other areas provided that due consideration is given to local conditions e.g. temperature. In the case of hollow sections formed from plate with the seam fusion welded, this European standard covers only the requirements of the plate material. Minimum yield strengths up to 460 MPa are specified together with low temperature impact properties at temperatures down to –40 °C. This European standard applies to material supplied ex-mill or from merchant\'s stock.
| Committee |
ISE/103
|
| DevelopmentNote |
Supersedes BS 7191(1989) and 94/713364 DC. (09/2001) Supersedes 08/30190326 DC. (07/2009)
|
| DocumentType |
Standard
|
| Pages |
80
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| UNE-EN 10225:2010 | Identical |
| NF EN 10225 : 2009 | Identical |
| NBN EN 10225 : 2009 | Identical |
| NEN EN 10225 : 2009 | Identical |
| NS EN 10225 : 2009 | Identical |
| I.S. EN 10225:2009 | Identical |
| SN EN 10225 : 2009 | Identical |
| UNI EN 10225 : 2009 | Identical |
| EN 10225:2009 | Identical |
| DIN EN 10225:2009-10 | Identical |
| 12/30241229 DC : 0 | BS 7910 - GUIDE TO METHODS FOR ASSESSING THE ACCEPTABILITY OF FLAWS IN METALLIC STRUCTURES |
| 02/703583 DC : DRAFT FEB 2002 | BS 7668 - WELDABLE STRUCTURAL STEELS - HOT FINISHED STRUCTURAL HOLLOW SECTIONS IN WEATHER RESISTANT STEELS |
| BS 7910(2013) : 2013 | GUIDE TO METHODS FOR ASSESSING THE ACCEPTABILITY OF FLAWS IN METALLIC STRUCTURES |
| W59-13 | Welded steel construction (metal arc welding) |
| ISO 6507-1:2005 | Metallic materials Vickers hardness test Part 1: Test method |
| EN ISO 12737:2010 | Metallic materials - Determination of plane-strain fracture toughness (ISO 12737:2010) |
| EN ISO 14284:2002 | Steel and iron - Sampling and preparation of samples for the determination of chemical composition (ISO 14284:1996) |
| EN 10002-1 : 2001 | METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT AMBIENT TEMPERATURE |
| EN 10052:1993 | Vocabulary of heat treatment terms for ferrous products |
| EN 10079:2007 | Definition of steel products |
| EN 10025-4:2004 | Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels |
| EN 10027-2:2015 | DESIGNATION SYSTEMS FOR STEELS - PART 2: NUMERICAL SYSTEM |
| EN 10029:2010 | Hot-rolled steel plates 3 mm thick or above - Tolerances on dimensions and shape |
| EN 10056-2:1993 | Structural steel equal and unequal leg angles - Part 2: Tolerances on shape and dimensions |
| EN 10164:2004 | Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions |
| EN 10246-12:2000 | Non-destructive testing of steel tubes - Part 12: Magnetic particle inspection of seamless and welded ferromagnetic steel tubes for the detection of surface imperfections |
| EN 10279:2000 | Hot rolled steel channels - Tolerances on shape, dimensions and mass |
| EN 10256:2000 | Non-destructive testing of steel tubes - Qualification and competence of level 1 and 2 non-destructive testing personnel |
| EN ISO 6947:2011 | Welding and allied processes - Welding positions (ISO 6947:2011) |
| EN 1011-1:2009 | Welding - Recommendations for welding of metallic materials - Part 1: General guidance for arc welding |
| EN 10034:1993 | Structural steel I and H sections - Tolerances on shape and dimensions |
| EN ISO 4063:2010 | Welding and allied processes - Nomenclature of processes and reference numbers (ISO 4063:2009, Corrected version 2010-03-01) |
| EN ISO 2566-1:1999 | Steel - Conversion of elongation values - Part 1: Carbon and low alloy steels (ISO 2566-1:1984) |
| ISO 12737:2010 | Metallic materials Determination of plane-strain fracture toughness |
| EN 895:1995 | Destructive tests on welds in metallic materials - Transverse tensile test |
| EN 10025-1:2004 | Hot rolled products of structural steels - Part 1: General technical delivery conditions |
| EN 473:2008 | Non-destructive testing - Qualification and certification of NDT personnel - General principles |
| EN 10024:1995 | Hot rolled taper flange I sections - Tolerances on shape and dimensions |
| EN 10210-1:2006 | Hot finished structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions |
| EN 10210-2:2006/AC:2007 | HOT FINISHED STRUCTURAL HOLLOW SECTIONS OF NON-ALLOY AND FINE GRAIN STEELS - PART 2: TOLERANCES, DIMENSIONS AND SECTIONAL PROPERTIES |
| EN 10045-1 : 1990 | METALLIC MATERIALS - CHARPY IMPACT TEST - PART 1: TEST METHOD |
| EN ISO 9934-1:2016 | Non-destructive testing - Magnetic particle testing - Part 1: General principles (ISO 9934-1:2016) |
| EN 10306:2001 | Iron and steel - Ultrasonic testing of H beams with parallel flanges and IPE beams |
| EN 10163-2:2004 | Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 2: Plate and wide flats |
| ISO 15614-1:2017 | Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys |
| EN 10246-7:2005 | Non-destructive testing of steel tubes - Part 7: Automatic full peripheral ultrasonic testing of seamless and welded (except submerged arc welded) tubes for the detection of longitudinal imperfections |
| EN 10021:2006 | General technical delivery conditions for steel products |
| BS 7363:1990 | Method for bead-on-plate (BOP) test for welds |
| ISO 2566-1:1984 | Steel Conversion of elongation values Part 1: Carbon and low alloy steels |
| ISO 9934-1:2016 | Non-destructive testing — Magnetic particle testing — Part 1: General principles |
| EN 10163-3:2004 | Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 3: Sections |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| EN 10246-3:1999 | Non-destructive testing of steel tubes - Part 3: Automatic eddy current testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of imperfections |
| EN 10027-1:2016 | Designation systems for steels - Part 1: Steel names |
| ISO 8492:2013 | Metallic materials Tube Flattening test |
| EN 10025-6:2004+A1:2009 | Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition |
| EN 10020:2000 | Definition and classification of grades of steel |
| EN ISO 8492:2013 | Metallic materials - Tube - Flattening test (ISO 8492:2013) |
| EN 10246-15:2000 | Non-destructive testing of steel tubes - Part 15: Automatic ultrasonic testing of strip/plate used in the manufacture of welded steel tubes for the detection of laminar imperfections |
| EN 10246-14:1999 | Non-destructive testing of steel tubes - Part 14: Automatic ultrasonic testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of laminar imperfections |
| ISO 4063:2009 | Welding and allied processes — Nomenclature of processes and reference numbers |
| EN 10055:1995 | Hot rolled steel equal flange tees with radiused root and toes - Dimensions and tolerances on shape and dimensions |
| EN 571-1:1997 | Non destructive testing - Penetrant testing - Part 1: General principles |
| EN 10160:1999 | Ultrasonic testing of steel flat product of thickness equal or greater than 6 mm (reflection method) |
| EN 10025-3:2004 | Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels |
| EN 10067:1996 | Hot rolled bulb flats - Dimensions and tolerances on shape, dimensions and mass |
| ISO 14284:1996 | Steel and iron — Sampling and preparation of samples for the determination of chemical composition |
| EN 10246-8:1999 | Non-destructive testing of steel tubes - Part 8: Automatic ultrasonic testing of the weld seam of electric welded steel tubes for the detection of longitudinal imperfections |
| ISO 6947:2011 | Welding and allied processes Welding positions |
| EN 10246-5 : 1999 | NON-DESTRUCTIVE TESTING OF STEEL TUBES - PART 5: AUTOMATIC FULL PERIPHERAL MAGNETIC TRANSDUCER/FLUX LEAKAGE TESTING OF SEAMLESS AND WELDED (EXCEPT SUBMERGED ARC WELDED) FERROMAGNETIC STEEL TUBES FOR THE DETECTION OF LONGITUDINAL IMPERFECTIONS |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.