• There are no items in your cart

BS EN 13244-5:2002

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage. Polyethylene (PE) Fitness for purpose of the system
Available format(s)

Hardcopy , PDF

Superseded date

11-30-2011

Language(s)

English

Published date

12-11-2003

Foreword
Introduction
1 Scope
2 Normative references
3 Definitions, symbols and abbreviations
4 Fitness for purpose of the system
  4.1 General
  4.2 Preparation of assemblies for testing
  4.3 Butt fusion joints
  4.4 Electrofusion joints
  4.5 Mechanical jointing
  4.6 Conditioning
  4.7 Retest in case of failure at 80 degrees C
  4.8 Compatibility
Bibliography

Describes the characteristics of the fitness for purpose of the assembled piping systems intended for buried and above-ground pressure systems for water for general purposes, drainage and sewerage.

Committee
PRI/88/2
DevelopmentNote
Together with BS EN 13244-1 and BS EN 13244-2, supersedes BS 6437(1984). Supersedes 98/122500 DC. (12/2003)
DocumentType
Standard
Pages
18
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes

BS EN 15014:2007 Plastics piping systems. Buried and above ground systems for water and other fluids under pressure. Performance characteristics for pipes, fittings and their joints
07/30138205 DC : DRAFT MAR 2007 BS 6297 - DESIGN AND INSTALLATION OF SMALL SEWAGE TREATMENT WORKS AND CESSPOOLS - CODE OF PRACTICE
EN 15014:2007 Plastics piping systems - Buried and above ground systems for water and other fluids under pressure - Performance characteristics for pipes, fittings and their joints

EN 13244-1:2002 Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 1: General
ISO 13953:2001 Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
EN 13244-4:2002 Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 4: Valves
EN 911:1995 Plastics piping systems - Elastomeric sealing ring type joints and mechanical joints for thermoplastics pressure piping - Test method for leaktightness under external hydrostatic pressure
ISO 11414:2009 Plastics pipes and fittings Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion
EN 715:1994 Thermoplastics piping systems - End-load bearing joints between small diameter pressure pipes and fittings - Test method for leaktightness under internal water pressure, including end thrust
EN 921:1994/AC:1995 PLASTICS PIPING SYSTEMS - THERMOPLASTICS PIPES - DETERMINATION OF RESISTANCE TO INTERNAL PRESSURE AT CONSTANT TEMPERATURE
EN 713:1993 Plastics piping systems - Mechanical joints between fittings and polyolefin pressure pipes - Test method for leaktightness under internal pressure of assemblies subjected to bending
ISO 13954:1997 Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
EN 13244-3:2002 Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 3: Fittings
ISO 13955:1997 Plastics pipes and fittings Crushing decohesion test for polyethylene (PE) electrofusion assemblies
ISO 11413:2008 Plastics pipes and fittings Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting
EN 13244-2:2002 Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 2: Pipes
EN 712:1993 Thermoplastics piping systems - End-load bearing mechanical joints between pressure pipes and fittings - Test method for resistance to pull-out under constant longitudinal force

View more information
US$170.10
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.