• There are no items in your cart

BS EN 14399-10:2009

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

High-strength structural bolting assemblies for preloading System HRC. Bolt and nut assemblies with calibrated preload
Available format(s)

Hardcopy , PDF

Superseded date

05-22-2018

Language(s)

English

Published date

07-31-2009

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Bolts
  4.1 Dimensions of bolts
  4.2 Specification for bolts and reference standards
  4.3 Marking of bolts
5 Nuts
  5.1 Dimensions of nuts
  5.2 Specification for nuts and reference standards
  5.3 Proof load values of nuts
  5.4 Decarburization of the nut thread
  5.5 Marking of nuts
6 Designation of the bolt/nut assembly
7 Associated washers
8 Functional characteristics of the bolt/nut/washer assembly
  8.1 General
  8.2 Suitability test for preloading
  8.3 Suitability test for calibrated preload
  8.4 Requirements
Bibliography

Describes the requirements for assemblies of high-strength structural bolts and nuts of system HRC suitable for preloaded joints, with hexagon head (large widths across flats) or cup head, thread sizes M12 to M30 and property class 10.9/10.

This part of this European Standard specifies, together with EN 14399-1, the requirements for assemblies of high-strength structural bolts and nuts of system HRC suitable for preloaded joints, with hexagon head (large widths across flats) or cup head, thread sizes M12 to M30 and property class 10.9/10. Bolt and nut assemblies conforming to this part of this European Standard have been designed to allow preloading of at least 0,7 fub X As ) according to EN 1993-1-8:2005 (Eurocode 3) and to obtain ductility predominantly by plastic elongation of the bolt. For this purpose the components have the following characteristics: - nut according to EN 14399-3, or - nut with height m = 1 d, - thread length of the bolt according to ISO 888. Bolt and nut assemblies conforming to this part of this European Standard include washer(s) according to EN 14399-6 or to EN 14399-5 (under the nut only). NOTE Attention is drawn to the importance of ensuring that the bolts are correctly used if a satisfactory result is to be obtained. The test method for suitability for preloading is specified in EN 14399-2 and in Clause 8.

Committee
FME/9
DevelopmentNote
Together with BS EN 14399-1, BS EN 14399-2, BS EN 14399-3, BS EN 14399-4, BS EN 14399-5, BS EN 14399-6, BS EN 14399-7 and BS EN 14399-8 it supersedes BS 4395-1(1969) and BS 4395-2(1969). Supersedes 07/30166055 DC. (07/2009)
DocumentType
Standard
Pages
24
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
EN 14399-10:2018 Identical

ISO 272:1982 Fasteners — Hexagon products — Widths across flats
ISO 898-2:2012 Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes — Coarse thread and fine pitch thread
EN 14399-3:2015 High-strength structural bolting assemblies for preloading - Part 3: System HR - Hexagon bolt and nut assemblies
ISO 10684:2004 Fasteners — Hot dip galvanized coatings
ISO 965-5:1998 ISO general purpose metric screw threads — Tolerances — Part 5: Limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance position h before galvanizing
ISO 4759-1:2000 Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C
ISO 6157-1:1988 Fasteners — Surface discontinuities — Part 1: Bolts, screws and studs for general requirements
EN 26157-1 : 1991 FASTENERS - SURFACE DISCONTINUITIES - PART 1: BOLTS, SCREWS AND STUDS FOR GENERAL REQUIREMENTS
ISO 965-2:1998 ISO general purpose metric screw threads — Tolerances — Part 2: Limits of sizes for general purpose external and internal screw threads — Medium quality
EN 20898-2 : 1993 MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES - COARSE THREAD (ISO 898-2:1992)
ISO 148-1:2016 Metallic materials — Charpy pendulum impact test — Part 1: Test method
EN 10045-1 : 1990 METALLIC MATERIALS - CHARPY IMPACT TEST - PART 1: TEST METHOD
EN ISO 4759-1 : 2000 TOLERANCES FOR FASTENERS - PART 1: BOLTS, SCREWS, STUDS AND NUTS - PRODUCT GRADES A, B AND C
EN ISO 3269:2000 FASTENERS - ACCEPTANCE INSPECTION
EN 14399-6:2015 High-strength structural bolting assemblies for preloading - Part 6: Plain chamfered washers
EN 14399-1:2015 High-strength structural bolting assemblies for preloading - Part 1: General requirements
ISO 888:2012 Fasteners — Bolts, screws and studs — Nominal lengths and thread lengths
EN 14399-4:2015 High-strength structural bolting assemblies for preloading - Part 4: System HV - Hexagon bolt and nut assemblies
EN ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013)
ISO 261:1998 ISO general purpose metric screw threads General plan
EN 1090-2:2008+A1:2011 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
ISO 6157-2:1995 Fasteners Surface discontinuities Part 2: Nuts
EN ISO 6157-2:2004 Fasteners - Surface discontinuities - Part 2: Nuts (ISO 6157-2:1995)
EN ISO 10684:2004/AC:2009 Fasteners - Hot dip galvanized coatings (ISO 10684:2004/Cor 1:2008)
EN 14399-5:2015 High-strength structural bolting assemblies for preloading - Part 5: Plain washers
EN 1993-1-8:2005/AC:2009 EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-8: DESIGN OF JOINTS
ISO 3269:2000 Fasteners Acceptance inspection
EN 14399-2:2015 High-strength structural bolting assemblies for preloading - Part 2: Suitability for preloading
ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread

View more information
US$237.18
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.