• There are no items in your cart

BS EN 1570-1 : 2011

Current
Current

The latest, up-to-date edition.

SAFETY REQUIREMENTS FOR LIFTING TABLES - PART 1: LIFTING TABLES SERVING UP TO TWO FIXED LANDINGS
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-01-2011

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of hazards
5 Safety requirements and/or protective measures
6 Verification of the safety requirements and/or measures
7 Information for use
Annex A (informative) - Overloading
Annex B (normative) - Noise
Annex C (normative) - Test procedures
Annex D (informative) - Controls
Annex E (normative) - Manual force measurement methods
Annex F (informative) - Signs
Annex ZA (informative) - Relationship between this European Standard
         and the Essential Requirements of EU Directive 2006/42/EC
Bibliography

Describes the safety requirements for industrial lifting tables for raising and/or lowering goods and the operator(s): - where the lifting table does not pass a fixed landing; - serving not more than 2 fixed landings.

Committee
MHE/12
DevelopmentNote
Supersedes BS EN 1570, 06/30147145 DC and 08/30180969 DC. (11/2011) 2011 Edition Re-Issued in October 2014 & incorporates AMD 1 2014. (10/2014)
DocumentType
Standard
Pages
70
PublisherName
British Standards Institution
Status
Current
Supersedes

Standards Relationship
EN 1570-1:2011+A1:2014 Identical

BS 7981:2017 Code of practice for the installation, maintenance, thorough examination and safe use of mast climbing work platforms (MCWPs)

CEN Guide 414:2017 Safety of machinery - Rules for the drafting and presentation of safety standards
ISO 2408:2017 Steel wire ropes — Requirements
ISO 4308-1:2003 Cranes and lifting appliances Selection of wire ropes Part 1: General
ISO 3691-5:2014 Industrial trucks Safety requirements and verification Part 5: Pedestrian-propelled trucks
EN 280:2013+A1:2015 Mobile elevating work platforms - Design calculations - Stability criteria - Construction - Safety - Examinations and tests
ISO 14122-3:2016 Safety of machinery — Permanent means of access to machinery — Part 3: Stairs, stepladders and guard-rails
ISO 11161:2007 Safety of machinery — Integrated manufacturing systems — Basic requirements
EN 1088:1995+A2:2008 Safety of machinery - Interlocking devices associated with guards - Principles for design and selection
CLC/TS 61496-2:2006 Safety of machinery - Electro-sensitive protective equipment - Part 2: Particular requirements for equipment using active opto-electronic protective devices (AOPDs)
IEC 61310-2:2007 Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking
ISO 11228-2:2007 Ergonomics Manual handling Part 2: Pushing and pulling
EN 61310-2:2008 Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking
ISO 13732-1:2006 Ergonomics of the thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces
ISO 4413:2010 Hydraulic fluid power General rules and safety requirements for systems and their components
EN 349:1993+A1:2008 Safety of machinery - Minimum gaps to avoid crushing of parts of the human body
IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
EN 61310-3:2008 Safety of machinery - Indication, marking and actuation - Part 3: Requirements for the location and operation of actuators
EN ISO 13850:2015 Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015)
IEC 60947-5-3:2013 Low-voltage switchgear and controlgear - Part 5-3: Control circuit devices and switching elements - Requirements for proximity devices with defined behaviour under fault conditions (PDDB)
IEC 61310-3:2007 Safety of machinery - Indication, marking and actuation - Part 3: Requirements for the location and operation of actuators
IEC 60947-5-1 : 4.0 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 5-1: CONTROL CIRCUIT DEVICES AND SWITCHING ELEMENTS - ELECTROMECHANICAL CONTROL CIRCUIT DEVICES
ISO 4308-2:1988 Cranes and lifting appliances Selection of wire ropes Part 2: Mobile cranes Coefficient of utilization
EN 528:2008 Rail dependent storage and retrieval equipment - Safety requirements
EN 1760-1:1997+A1:2009 Safety of machinery - Pressure sensitive protective devices - Part 1: General principles for the design and testing of pressure sensitive mats and pressure sensitive floors
ISO 606:2015 Short-pitch transmission precision roller and bush chains, attachments and associated chain sprockets
EN 81-1:1998+A3:2009 Safety rules for the construction and installation of lifts - Part 1: Electric lifts
EN 81-41:2010 Safety rules for the construction and installation of lifts - Special lifts for the transport of persons and goods - Part 41: Vertical lifting platforms intended for use by persons with impaired mobility
EN ISO 13857:2008 Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008)
ISO 12100:2010 Safety of machinery — General principles for design — Risk assessment and risk reduction
EN 81-31:2010 Safety rules for the construction and installation of lifts - Lifts for the transport of goods only - Part 31: Accessible goods only lifts
EN 1493:2010 Vehicle lifts
EN ISO 13732-1:2008 Ergonomics of the thermal environment - Methods for the assessment of human responses to contact with surfaces - Part 1: Hot surfaces (ISO 13732-1:2006)
EN ISO 11161:2007/A1:2010 SAFETY OF MACHINERY - INTEGRATED MANUFACTURING SYSTEMS - BASIC REQUIREMENTS
EN ISO 14122-3:2016 Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails (ISO 14122-3:2016)
EN 61496-1:2013/AC:2015 SAFETY OF MACHINERY - ELECTRO-SENSITIVE PROTECTIVE EQUIPMENT - PART 1: GENERAL REQUIREMENTS AND TESTS (IEC 61496-1:2012)
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
EN 13241-1:2003+A1:2011 Industrial, commercial and garage doors and gates - Product standard - Part 1: Products without fire resistance or smoke control characteristics
EN ISO 4414:2010 Pneumatic fluid power - General rules and safety requirements for systems and their components (ISO 4414:2010)
EN ISO 3691-5:2015/AC:2016 INDUSTRIAL TRUCKS - SAFETY REQUIREMENTS AND VERIFICATION - PART 5: PEDESTRIAN-PROPELLED TRUCKS (ISO 3691-5:2014)
EN 81-2 : 1998 + A3 2009 SAFETY RULES FOR THE CONSTRUCTION AND INSTALLATION OF LIFTS - PART 2: HYDRAULIC LIFTS
EN 1915-2:2001+A1:2009 Aircraft ground support equipment - General requirements - Part 2: Stability and strength requirements, calculations and test methods
ISO 13857:2008 Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs
IEC 61496-1:2012 Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests
EN ISO 12100:2010 Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010)
EN ISO 13849-1:2015 Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015)
ISO 4414:2010 Pneumatic fluid power General rules and safety requirements for systems and their components
ISO 3864-3:2012 Graphical symbols — Safety colours and safety signs — Part 3: Design principles for graphical symbols for use in safety signs
ISO 13850:2015 Safety of machinery Emergency stop function Principles for design
IEC 61310-1:2007 Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals
EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
ISO 4301-1:2016 Cranes — Classification — Part 1: General
EN ISO 4413:2010 Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010)
ISO 11228-1:2003 Ergonomics Manual handling Part 1: Lifting and carrying
EN 1777:2010 Hydraulic platforms (HPs) for fire fighting and rescue services - Safety requirements and testing
EN 60947-5-3:2013 Low-voltage switchgear and controlgear - Part 5-3: Control circuit devices and switching elements - Requirements for proximity devices with defined behaviour under fault conditions (PDDB)
ISO 13849-1:2015 Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design
EN 61310-1:2008 Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals
IEC 61496-2:2013 Safety of machinery - Electro-sensitive protective equipment - Part 2: Particular requirements for equipment using active opto-electronic protective devices (AOPDs)
EN 60204-1 : 2006 COR 2010 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS

View more information
US$311.44
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.