• There are no items in your cart

BS EN 60770-3:2014

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Transmitters for use in industrial-process control systems Methods for performance evaluation of intelligent transmitters
Available format(s)

Hardcopy , PDF

Superseded date

05-10-2021

Language(s)

English

Published date

09-30-2014

INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Design assessment
5 Performance testing
6 Other considerations
7 Evaluation report
Annex A (informative) - Dependability testing
Annex B (informative) - Throughput testing
Annex C (informative) - Function block testing
Bibliography
Annex ZA (normative) - Normative references to
         international publications with their
         corresponding European publications

Pertains to intelligent transmitters, which convert one or more physical, chemical or electrical quantities into digital signals for use in a communication network (as specified in the IEC 61158 series or others) or into analogue electrical signals.

This part of IEC 60770 specifies the following methods.

  • Methods for

  • assessment of the functionality of intelligent transmitters;

  • testing the operational behaviour, as well as the static and dynamic performance of an intelligent transmitter.

  • Methodologies for

  • determining the reliability and diagnostic features used to detect malfunctions;

  • determining the communication capabilities of the intelligent transmitters in a communication network.

The methods and methodologies are applicable to intelligent transmitters, which convert one or more physical, chemical or electrical quantities into digital signals for use in a communication network (as specified in the IEC 61158 series or others) or into analogue electrical signals (as specified in the IEC 60381 series).

The methods and methodologies listed in this part of IEC 60770 are intended for use by:

  • manufacturers to determine the performance of their products, and

  • users or independent testing laboratories to verify equipment performance specifications.

Manufacturers of intelligent transmitters are urged to apply this part of IEC 60770 at an early stage of development.

This standard is intended to provide guidance for designing evaluations of intelligent transmitters by providing:

  • a checklist for reviewing the hardware and software design in a structured way;

  • test methods for measuring and qualifying the performance, dependability and operability under various environmental and operational conditions;

  • methods for reporting the data obtained.

Committee
GEL/65/2
DevelopmentNote
Supersedes 03/313373 DC (07/2006) 2006 Edition remains active & will be withdrawn on 27/06/2017. (09/2014)
DocumentType
Standard
Pages
62
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
DIN EN 60770-3 : 2015 Identical
NF EN 60770-3 : 2014 Identical
I.S. EN 60770-3:2014 Identical
EN 60770-3:2014 Identical
NBN EN 60770-3 : 2014 Identical
SN EN 60770-3:2014 Identical
IEC 60770-3:2014 Identical

EN 61298-1:2008 PROCESS MEASUREMENT AND CONTROL DEVICES - GENERAL METHODS AND PROCEDURES FOR EVALUATING PERFORMANCE - PART 1: GENERAL CONSIDERATIONS
IEC 61298-1:2008 Process measurement and control devices - General methods and procedures for evaluating performance - Part 1: General considerations
EN 61298-3:2008 Process measurement and control devices - General methods and procedures for evaluating performance - Part 3: Tests for the effects of influence quantities
IEC 61298-2:2008 Process measurement and control devices - General methods and procedures for evaluating performance - Part 2: Tests under reference conditions
EN 61298-2:2008 PROCESS MEASUREMENT AND CONTROL DEVICES - GENERAL METHODS AND PROCEDURES FOR EVALUATING PERFORMANCE - PART 2: TESTS UNDER REFERENCE CONDITIONS
EN 61298-4:2008 Process measurement and control devices - General methods and procedures for evaluating performance - Part 4: Evaluation report content
EN 60068-2-1:2007 Environmental testing - Part 2-1: Tests - Test A: Cold
EN 60068-2-2:2007 Environmental testing - Part 2-2: Tests - Test B: Dry heat
IEC 60068-2-31:2008 Environmental testing - Part 2-31: Tests - Test Ec: Rough handling shocks, primarily for equipment-type specimens
EN 61326-1:2013 Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 1: General requirements
HD 452.1 : 200S1 ANALOGUE SIGNALS FOR PROCESS CONTROL SYSTEMS - DIRECT CURRENT SIGNALS
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
IEC 61298-3:2008 Process measurement and control devices - General methods and procedures for evaluating performance - Part 3: Tests for the effects of influence quantities
IEC 60068-2-2:2007 Environmental testing - Part 2-2: Tests - Test B: Dry heat
EN 61032:1998 Protection of persons and equipment by enclosures - Probes for verification
EN 60068-2-78:2013 Environmental testing - Part 2-78: Tests - Test Cab: Damp heat, steady state
IEC TS 62098:2000 Evaluation methods for microprocessor- based instruments
IEC 61298-4:2008 Process measurement and control devices - General methods and procedures for evaluating performance - Part 4: Evaluation report content
EN 60068-2-6:2008 Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal)
CISPR 11:2015 RLV Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods of measurement
IEC 60068-2-1:2007 Environmental testing - Part 2-1: Tests - Test A: Cold
EN 61010-1:2010 Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 1: General requirements
EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
IEC 61032:1997 Protection of persons and equipment by enclosures - Probes for verification
IEC 61010-1:2010+AMD1:2016 CSV Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 1: General requirements
EN 60068-2-31:2008 ENVIRONMENTAL TESTING - PART 2-31: TESTS - TEST EC: ROUGH HANDLING SHOCKS, PRIMARILY FOR EQUIPMENT-TYPE SPECIMENS

View more information
US$311.44
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.