• There are no items in your cart

BS EN IEC 60793-1-47:2018

Current
Current

The latest, up-to-date edition.

Optical fibres Measurement methods and test procedures. Macrobending loss
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

02-26-2018

FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Apparatus
5 Specimen
6 Procedure
7 Calculations
8 Results
9 Specification information
Annex A (normative) - Change in transmittance by
        transmitted power technique
Annex B (normative) - Cut-back technique
Annex D (informative) - Small bend radius phenomena
Annex E (informative) - Parallel plate (2-point)
        macrobend loss approximation
Bibliography
Annex ZA (normative) - Normative references to
         international publications with their
         corresponding European publications

Sets of uniform requirements for measuring the macrobending loss of single-mode fibres (class B) at 1550 nm or 1625 nm, category A1 multimode fibres at 850 nm or 1300 nm, and category A3 and A4 multimode fibres at 650 nm, 850 nm or 1300 nm, thereby assisting in the inspection of fibres and cables for commercial purposes.

This part of IEC60793 establishes uniform requirements for measuring the macrobending loss of single-mode fibres (class B) at 1550nm or 1625nm, category A1 multimode fibres at 850nm or 1300nm, and category A3 and A4 multimode fibres at 650nm, 850nm or 1300nm, thereby assisting in the inspection of fibres and cables for commercial purposes. This document gives two methods for measuring macrobending sensitivity: Method A– Fibre winding, pertains to class B single-mode fibres and category A1 multimode fibres. Method B– Quarter circle bends, pertains to category A3 and A4 multimode fibres. For both of these methods, the macrobending loss can be measured utilizing general fibre attenuation techniques, for example the power monitoring technique (see AnnexA) or the cut-back technique (see AnnexB). Methods A and B are expected to produce different results if they are applied to the same fibre. This is because the key difference between the two methods is the deployment, including the bend radius and length of fibre that is bent. The reason for the difference is that A3 and A4 multimode fibres are expected to be deployed in short lengths with a smaller number of bends per unit fiber length compared to single-mode and category A1 multimode fibres. In this document, the \'curvature radius\' is defined as the radius of the suitable circular shaped support (e.g. mandrel or guiding groove on a flat surface) on which the fibre can be bent. In addition, informative AnnexE has been added to approximate bend loss for class B single-mode fibres across a broad wavelength range at various effective bends.

Committee
GEL/86/1
DevelopmentNote
Supersedes 16/30337880 DC & BS EN 60793-1-47. (03/2018)
DocumentType
Standard
Pages
40
PublisherName
British Standards Institution
Status
Current
Supersedes

Standards Relationship
EN IEC 60793-1-47:2018 Identical
IEC 60793-1-47:2017 Identical
IEC 60793-1-47 : 4.0 Identical

IEC 60793-1-1 : 2017 OPTICAL FIBRES - PART 1-1: MEASUREMENT METHODS AND TEST PROCEDURES - GENERAL AND GUIDANCE
IEC 60793-2-10:2017 Optical fibres - Part 2-10: Product specifications - Sectional specification for category A1 multimode fibres
EN 60793-1-1:2017 Optical fibres - Part 1-1: Measurement methods and test procedures - General and guidance
IEC 60793-2:2015 Optical fibres - Part 2: Product specifications - General
EN 60793-2-10:2017 Optical fibres - Part 2-10: Product specifications - Sectional specification for category A1 multimode fibres
IEC TR 62547:2013 Guidelines for the measurement of high-power damage sensitivity of single-mode fibre to bends - Guidance for interpretation of results
IEC 60793-1-46:2001 Optical fibres - Part 1-46: Measurement methods and test procedures - Monitoring of changes in optical transmittance
IEC 60793-1-40:2001 Optical fibres - Part 1-40: Measurement methods and test procedures - Attenuation
IEC 61280-4-1:2009 Fibre-optic communication subsystem test procedures - Part 4-1: Installed cable plant - Multimode attenuation measurement
EN 61280-1-4:2010 Fibre optic communication subsystem test procedures - Part 1-4: General communication subsystems - Light source encircled flux measurement method
EN 60793-2:2016 Optical fibres - Part 2: Product specifications - General
IEC 60793-2-50:2015 Optical fibres - Part 2-50: Product specifications - Sectional specification for class B single-mode fibres
EN 61280-4-1:2009 FIBRE OPTIC COMMUNICATION SUBSYSTEM TEST PROCEDURES - PART 4-1: INSTALLED CABLE PLANT - MULTIMODE ATTENUATION MEASUREMENT
IEC 61280-1-4:2009 Fibre optic communication subsystem test procedures - Part 1-4: General communication subsystems - Light source encircled flux measurement method

View more information
US$261.13
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.