BS ISO 12151-2 : 2003

CONNECTIONS FOR HYDRAULIC FLUID POWER AND GENERAL USE - HOSE FITTINGS - PART 2: HOSE FITTINGS WITH ISO 8434-1 AND ISO 8434-4 24 DEGREE CONE CONNECTOR ENDS WITH O-RINGS

British Standards Institution

Current

Add To Cart

Product Format

Table of Contents - (Show below) - (Hide below)

Foreword Introduction 1 Scope 2 Normative references 3 Terms and definitions 4 Performance requirements 5 Designation of hose fittings 6 Design 7 Manufacture 8 Assembly instructions 9 Procurement information 10 Marking 11 Identification statement (Reference to this part of ISO 12151) Bibliography

Abstract - (Show below) - (Hide below)

Describes the general and dimensional requirements for the design and performance of hose fittings with 24 degree cone connector ends with O-rings, in accordance with ISO 8434-1 and ISO 8434-4. These hose fittings are made of carbon steel and are intended for use with hoses with nominal inside diameters form 5 mm through 38 mm (inclusive).

General Product Information - (Show below) - (Hide below)

Published
Document Type	Standard
Status	Current
Publisher	British Standards Institution
Pages
ISBN
Committee	MCE/18/-/4
Supersedes	01/714271 DC : DRAFT NOV 2001

International Equivalents – Equivalent Standard(s) & Relationship - (Show below) - (Hide below)

Equivalent Standard(s)	Relationship
ISO 12151-2 : 2003(R2015)	Identical

Standards Referencing This Book - (Show below) - (Hide below)

ISO 4079-1 : 2001	RUBBER HOSES AND HOSE ASSEMBLIES - TEXTILE-REINFORCED HYDRAULIC TYPES - SPECIFICATION - PART 1: OIL-BASED FLUID APPLICATIONS
ISO 4039-1 : 1998(R2008)	ROAD VEHICLES - PNEUMATIC BRAKING SYSTEMS - PART 1: PIPES, MALE FITTINGS AND TAPPED HOLES WITH FACIAL SEALING SURFACE
ISO 8434-1 : 2007	METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - PART 1: 24 DEGREE CONE CONNECTORS
ISO 3949 : 2009	PLASTICS HOSES AND HOSE ASSEMBLIES - TEXTILE-REINFORCED TYPES FOR HYDRAULIC APPLICATIONS - SPECIFICATION
ISO 5598 : 2008	FLUID POWER SYSTEMS AND COMPONENTS - VOCABULARY
ISO 4759-1 : 2000(R2017)	TOLERANCES FOR FASTENERS - PART 1: BOLTS, SCREWS, STUDS AND NUTS - PRODUCT GRADES A, B AND C
ISO 4397 : 2011(R2017)	FLUID POWER CONNECTORS AND ASSOCIATED COMPONENTS - NOMINAL OUTSIDE DIAMETERS OF TUBES AND NOMINAL HOSE SIZES
ISO 4039-2 : 1998(R2008)	ROAD VEHICLES - PNEUMATIC BRAKING SYSTEMS - PART 2: PIPES, MALE FITTINGS AND HOLES WITH CONICAL SEALING SURFACE
ISO 4038 : 1996(R2018)	ROAD VEHICLES - HYDRAULIC BRAKING SYSTEMS - SIMPLE FLARE PIPES, TAPPED HOLES, MALE FITTINGS AND HOSE END FITTINGS
ISO 1436-1 : 2001	RUBBER HOSES AND HOSE ASSEMBLIES - WIRE-BRAID-REINFORCED HYDRAULIC TYPES - SPECIFICATION - PART 1: OIL-BASED FLUID APPLICATIONS
ISO 8434-5 : 1995	METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - TEST METHODS FOR THREADED HYDRAULIC FLUID POWER CONNECTIONS
ISO 8434-4 : 1995	METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - PART 4: 24 DEGREE CONE CONNECTORS WITH O-RING WELD-ON NIPPLES
ISO 9227 : 2017	CORROSION TESTS IN ARTIFICIAL ATMOSPHERES - SALT SPRAY TESTS
ISO 3862-1 : 2001	RUBBER HOSES AND HOSE ASSEMBLIES - RUBBER-COVERED SPIRAL-WIRE-REINFORCED HYDRAULIC TYPES - SPECIFICATION - PART 1: OIL-BASED FLUID APPLICATIONS