CSA A440 : 2017
Current
The latest, up-to-date edition.
NORTH AMERICAN FENESTRATION STANDARD/SPECIFICATION FOR WINDOWS, DOORS, AND SKYLIGHTS
Hardcopy , PDF
English
01-01-2017
Preface
0 Introduction
1 Scope
2 Reference publications
3 Definitions
4 General requirements
5 Class R and LC windows and sliding doors
6 Side-hinged and folding doors (all classes)
7 Class CW and AW windows and sliding doors
8 Unit skylights, including roof windows and tubular
daylighting devices (TDDs)
9 General testing requirements
10 Material requirements
11 Component requirements
12 Fenestration type and test size requirements
Annex A (informative) - Commentary
Annex B (informative) - Contact information for organizations
listed in Clause 2
Annex C (informative) - Certification
Annex D (informative) - Standards progression - Windows,
doors and unit skylights
Pertains to both operating and fixed, new construction and replacement windows, doors, SSPs, TDDs, roof windows, and unit skylights installed into exterior building envelopes.
DevelopmentNote |
Jointly Published by AAMA, WDMA & CSA. Also numbered as AAMA 101/I.S. 2/NAFS. (02/2008) 2008 Edition is still active with Supplement. (12/2011) A USER GUIDE exists for 2011 Edition of standard, see CSA PLUS A440H. (02/2017) 2011 Edition is still active with GEN INS 1, 2, and Supp 1(CSA A440S1, separately available). (01/2018)
|
DocumentType |
Standard
|
ISBN |
978-1-4883-0955-7
|
Pages |
236
|
PublisherName |
Canadian Standards Association
|
Status |
Current
|
Supersedes |
ANSI H35.2 : 2017 | DIMENSIONAL TOLERANCES FOR ALUMINUM MILL PRODUCTS |
ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
WDMA IS 11 : 2016 | ANALYTICAL METHOD FOR DESIGN PRESSURE (DP) RATINGS OF FENESTRATION PRODUCTS |
BHMA A156.12 : 2013 | INTERCONNECTED LOCKS |
ANSI A250.8 : 2014 | SPECIFICATIONS FOR STANDARD STEEL DOORS AND FRAMES |
ASTM D 2287 : 2012 : REDLINE | Standard Specification for Nonrigid Vinyl Chloride Polymer and Copolymer Molding and Extrusion Compounds |
ASTM D 618 : 2013 : REDLINE | Standard Practice for Conditioning Plastics for Testing |
ASTM D 1929 : 2016 : REDLINE | Standard Test Method for Determining Ignition Temperature of Plastics |
ANSI Z97.1 : 2015 | SAFETY GLAZING MATERIALS USED IN BUILDINGS - SAFETY PERFORMANCE SPECIFICATIONS AND METHODS OF TEST |
ASTM E 1613 : 2012 : REDLINE | Standard Test Method for Determination of Lead by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES), Flame Atomic Absorption Spectrometry (FAAS), or Graphite Furnace Atomic Absorption Spectrometry (GFAAS) Techniques |
BHMA A156.17 : 2014 | SELF CLOSING HINGES AND PIVOTS |
ASTM D 3656/D3656M : 2013 : REDLINE | Standard Specification for Insect Screening and Louver Cloth Woven from<brk/>Vinyl-Coated Glass Yarns |
ASTM E 2203 : 2014 : R2018 | Standard Specification for Dense Thermoplastic Elastomers Used for Compression Seals, Gaskets, Setting Blocks, Spacers and Accessories |
ASTM D 6098 : 2016 : REDLINE | Standard Classification System and Basis for Specification for Extruded and Compression Molded Shapes Made from Polycarbonate (PC) |
SMA 1201 : 2013 | SPECIFICATIONS FOR INSECT SCREENS FOR WINDOWS, SLIDING DOORS, AND SWINGING DOORS |
CGSB 12.9 : M91 | SPANDREL GLASS |
ASTM C 1115 : 2017 : REDLINE | Standard Specification for Dense Elastomeric Silicone Rubber Gaskets and Accessories |
ASTM A 123/A123M : 2017 : REDLINE | Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products |
ASTM F 842 : 2017 : REDLINE | Standard Test Methods for Measuring the Forced Entry Resistance of Sliding Door Assemblies, Excluding Glazing Impact |
CSA Z234.1 : 0 | METRIC PRACTICE GUIDE |
ASTM D 4673 : 2016 : REDLINE | Standard Classification System for and Basis for Specification for Acrylonitrile–Butadiene–Styrene (ABS) Plastics and Alloys Molding and Extrusion Materials |
BHMA A156.18 : 2016 | MATERIALS AND FINISHES |
ANSI A250.10 : 2011 | TEST PROCEDURE AND ACCEPTANCE CRITERIA FOR - PRIME PAINTED STEEL SURFACES FOR STEEL DOORS AND FRAMES |
ASTM B 456 : 2017 : REDLINE | Standard Specification for Electrodeposited Coatings of Copper Plus Nickel Plus<brk/> Chromium and Nickel Plus Chromium |
FM 4430 : 2012 | HEAT AND SMOKE VENTS |
CGSB 12.20 : M89 | STRUCTURAL DESIGN OF GLASS FOR BUILDINGS |
CFR 16(PTS1000-END) : 0 | COMMERCIAL PRACTICES - FEDERAL TRADE COMMISSION - CONSUMER PRODUCT SAFETY COMMISSION |
CGSB 12.4 : M1991(R2017) | HEAT ABSORBING GLASS |
ASTM E 1300 : 2016 : REDLINE | Standard Practice for Determining Load Resistance of Glass in Buildings |
NAGDM 105 : 1992 | TEST METHOD FOR THERMAL TRANSMITTANCE & AIR INFILTRATION OF GARAGE DOORS |
BHMA A156.22 : 2017 | DOOR GASKETING AND EDGE SEAL SYSTEMS |
IEEE/ASTM SI_10-2010 | American National Standard for Metric Practice |
ASTM D 6865 : 2017 : REDLINE | Standard Classification System and Basis for Specifications for Acrylonitrile–Styrene–Acrylate (ASA) and Acrylonitrile–EPDM–Styrene (AES) Plastics and Alloys Molding and Extrusion Materials |
WDMA IS 10 : 2013 | INDUSTRY STANDARD FOR TESTING CELLULOSIC COMPOSITE MATERIALS FOR USE IN FENESTRATION PRODUCTS |
BHMA A156.5 : 2014 | CYLINDER AND INPUT DEVICES FOR LOCKS |
ASTM E 331 : 2000 | Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure Difference |
ASTM F 588 : 2017 : REDLINE | Standard Test Methods for Measuring the Forced Entry Resistance of Window Assemblies, Excluding Glazing Impact |
ASCE 7 10 : 2010 | MINIMUM DESIGN LOADS FOR BUILDINGS AND OTHER STRUCTURES |
CGSB 12.2 : M1991(R2017) | FLAT, CLEAR SHEET GLASS |
ASTM D 1003 : 2013 : REDLINE | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics |
ASTM D 790 : 2017 : REDLINE | Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials |
SMA 7001 : 2013 | WARNING LABEL STANDARD FOR WINDOW INSECT SCREENS |
A440S1-17 | Canadian Supplement to AAMA/WDMA/CSA 101/I.S.2/A440-11, NAFS - North American Fenestration Standard/Specification for windows, doors, and skylights |
ASTM B 209 : 2014 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate |
ASTM G 155 : 2013 : REDLINE | Standard Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials |
ASTM D 4549 : 2015 : REDLINE | Standard Classification System and Basis for Specification for Polystyrene and Rubber-Modified Polystyrene Molding and Extrusion Materials (PS) |
ASTM E 330/E330M : 2014 : REDLINE | Standard Test Method for Structural Performance of Exterior Windows, Doors, Skylights and Curtain Walls by Uniform Static Air Pressure Difference |
SMA 1101 : 2016 | SPECIFICATIONS FOR RETRACTABLE INSECT SCREENS |
WDMA IS4 : 2015A | INDUSTRY SPECIFICATION FOR PRESERVATIVE TREATMENT FOR MILLWORK |
BHMA A156.2 : 2017 | BORED AND PREASSEMBLED LOCKS AND LATCHES |
CGSB 12.12 : M90 | PLASTIC SAFETY GLAZING SHEETS |
ASTM D 2565 : 2016 : REDLINE | Standard Practice for Xenon-Arc Exposure of Plastics Intended for Outdoor Applications |
ASTM D 2843 : 2016 : REDLINE | Standard Test Method for Density of Smoke from the Burning or Decomposition of Plastics |
BHMA A156.1 : 2016 | BUTTS AND HINGES |
CGSB 12.1 : 2017 CORR 1 2017 | SAFETY GLAZING |
ASTM C 1036 : 2016 : REDLINE | Standard Specification for Flat Glass |
IWS 089 : 1990 | RECOMMENDED STANDARDS & SPECIFICATIONS FOR INSECT WIRE SCREENING (WIRE FABRIC) |
CGSB 12.8 : 2017 | INSULATING GLASS UNITS |
ADM 1 : 2015 | ALUMINUM DESIGN MANUAL |
CGSB 1.210 : 2003 CORR 1 2005 | QUICK-DRYING ALKYD PRIMER FOR STRUCTURAL STEEL |
CGSB 12.3 : M1991(R2017) | FLAT, CLEAR FLOAT GLASS |
ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
BHMA A156.13 : 2017 | MORTISE LOCKS AND LATCHES, SERIES 1000 |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.