• There are no items in your cart

DD CEN/TS 1555-7:2003

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Plastics piping systems for the supply of gaseous fuels. Polyethylene (PE) Guidance for the assessment of conformity
Available format(s)

Hardcopy , PDF

Superseded date

03-31-2013

Language(s)

English

Published date

01-08-2004

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions, symbols and abbreviations
  3.1 Terms and definitions
  3.2 Abbreviations
4 Requirements
  4.1 General
  4.2 Testing and inspection
  4.3 Technical file
Annex A (normative) Change of compound
        A.1 General
        A.2 Change
        A.3 Type testing required for re-evaluation
Bibliography

Provides guidance for assessment of conformity to be included in the manufacturer's quality plan as part of the quality system.

Committee
PRI/88/2
DevelopmentNote
Supersedes 95/125454 DC (03/2004)
DocumentType
Standard
Pages
34
PublisherName
British Standards Institution
RevisionOf
Status
Superseded
SupersededBy
Supersedes

BS 5391-1:2006 Acrylonitrile-butadiene-styrene (ABS) pressure pipe Specification

EN ISO 12162:2009 Thermoplastics materials for pipes and fittings for pressure applications - Classification, designation and design coefficient (ISO 12162:2009)
EN 1555-1:2010 Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General
EN 1555-3:2010+A1:2012 Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings
ISO 13953:2001 Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
EN 728:1997 Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time
ISO 10838-3:2001 Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 3: Thermoplastics fittings for pipes of nominal outside diameter less than or equal to 63 mm
EN 45011:1998 General requirements for bodies operating product certification systems (ISO/IEC Guide 65:1996)
ISO 10838-2:2000 Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 2: Metal fittings for pipes of nominal outside diameter greater than 63 mm
ISO 10838-1:2000 Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 1: Metal fittings for pipes of nominal outside diameter less than or equal to 63 mm
ISO 13477:2008 Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Small-scale steady-state test (S4 test)
ISO 2859-2:1985 Sampling procedures for inspection by attributes — Part 2: Sampling plans indexed by limiting quality (LQ) for isolated lot inspection
EN 45011 : 1998 GENERAL REQUIREMENTS FOR BODIES OPERATING PRODUCT CERTIFICATION SYSTEMS
ISO 6259-1:2015 Thermoplastics pipes Determination of tensile properties Part 1: General test method
EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
ISO 13954:1997 Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
EN 1555-4:2011 Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 4: Valves
ISO 13955:1997 Plastics pipes and fittings Crushing decohesion test for polyethylene (PE) electrofusion assemblies
EN 1555-5:2010 Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5: Fitness for purpose of the system
EN 12007-2:2012 Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 2: Specific functional requirements for polyethylene (MOP up to and including 10 bar)
EN 1555-2:2010 Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 2: Pipes
ISO 6259-3:2015 Thermoplastics pipes Determination of tensile properties Part 3: Polyolefin pipes
EN 45012 : 1998 GENERAL REQUIREMENTS FOR BODIES OPERATING ASSESSMENT AND CERTIFICATION/REGISTRATION OF QUALITY SYSTEMS
EN ISO 9000:2015 Quality management systems - Fundamentals and vocabulary (ISO 9000:2015)

View more information
US$277.90
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.