DIN 267-9:1979-08
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
MECHANICAL FASTENERS - TECHNICAL CONDITIONS OF DELIVERY, COMPONENTS WITH ELECTROPLATED COATINGS
Superseded date
06-01-1992
Published date
01-12-2013
Kein Inhaltsverzeichnis in der Norm vorhanden.
| DocumentType |
Standard
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| ISO 4042:1999 | Similar to |
| DIN 6907:1990-12 | SERRATED LOCK WASHERS WITH EXTERNAL TEETH FOR SCREW AND WASHER ASSEMBLIES |
| DIN 71428:1989-11 | COMPRESSION COUPLINGS WITH OLIVES - CYLINDRICAL THREAD NIPPLES FOR USE WITH UNION NUTS |
| DIN 1142:1982-01 | WIRE ROPE GRIPS FOR ROPE TERMINATIONS TO MEET SAFETY REQUIREMENTS |
| DIN 94:1983-09 | SPLIT PINS |
| DIN 7972:1990-08 | SLOTTED COUNTERSUNK HEAD TAPPING SCREWS |
| DIN 820-25:1980-12 | STANDARDIZATION; PRESENTATION OF STANDARDS; MATERIAL, FINISH, INSTRUCTIONS OF DELIVERY, MARKING |
| DIN 7631:1985-01 | Compression couplings with spherical liner; straight compression couplings |
| DIN 964:1990-08 | SLOTTED RAISED COUNTERSUNK (OVAL) HEAD SCREWS |
| DIN 7999:1983-12 | HIGH TENSILE STRENGTH HEXAGON FIT BOLTS WITH LARGE WIDTH ACROSS FLATS FOR STRUCTURAL BOLTING |
| DIN 9021:1990-03 | WASHERS WITH OUTSIDE DIAMETER CA. 3 X NOMINAL THREAD DIAMETER |
| DIN 6922:1983-06 | HEXAGON FLANGE BOLTS WITH REDUCED SHANK |
| DIN 966:1990-08 | CROSS RECESSED RAISED COUNTERSUNK HEAD SCREWS |
| DIN 7985:1990-08 | CROSS RECESSED RAISED CHEESE HEAD SCREWS |
| DIN 522:1990-03 | WASHERS, OF METALLIC MATERIALS - TECHNICAL SPECIFICATION |
| DIN 71429:1989-11 | COMPRESSION COUPLINGS WITH OLIVES - BULKHEAD COMPRESSION COUPLINGS SMALL STUD AND ELBOW FITTINGS FOR USE WITH UNION NUTS |
| DIN 436:1990-05 | SQUARE WASHERS; ESPECIALLY FOR WOOD CONSTRUCTIONS |
| DIN 25202:1992-04 | RAILWAY VEHICLES - SECURING OF BOLTED JOINTS - INITIAL STRESSING FORCES AND TIGHTENING TORQUES |
| DIN 8912:1990-06 | COUPLING NUTS AND SCREWED PLUGS FOR USE WITH PN 40 FLARED FLANGE SOLDERLESS COMPRESSION COUPLINGS IN REFRIGERATING SYSTEMS |
| DIN 965:1990-08 | CROSS RECESSED COUNTERSUNK (FLAT) HEAD SCREWS |
| DIN 43673-1:1982-02 | DRILLED HOLES AND SCREW CONNECTIONS FOR BUSBARS; RECTANGULAR CROSS SECTION BUSBARS |
| DIN 6927:1983-11 | PREVAILING TORQUE TYPE HEXAGON FLANGE NUTS, ALL METAL NUTS |
| DIN 50982-1:1987-08 | PRINCIPLES OF COATING THICKNESS MEASUREMENT - TERMINOLOGY ASSOCIATED WITH COATING THICKNESS AND MEASURING AREAS |
| DIN 7632:1985-01 | Compression couplings with spherical liner; reducers |
| DIN 7983:1990-08 | CROSS RECESSED RAISED COUNTERSUNK HEAD TAPPING SCREWS |
| DIN 8906:1990-06 | PN 40 FLARED FLANGE SOLDERLESS COMPRESSION COUPLINGS FOR USE IN REFRIGERATING SYSTEMS |
| DIN 71412:1987-11 | LUBRICATING NIPPLES - CONE TYPE |
| DIN 915:1980-12 | HEXAGON SOCKET SET SCREWS WITH DOG POINT, ISO 4028 MODIFIED |
| DIN 914:1980-12 | HEXAGON SOCKET SET SCREWS WITH CONE POINT, ISO 4027 MODIFIED |
| DIN 125-2:1990-03 | PRODUCT GRADE A WASHERS WITH A HARDNESS FROM 300 HV, DESIGNED FOR USE WITH HEXAGON HEAD BOLTS AND NUTS |
| DIN 71436:1989-11 | COMPRESSION COUPLINGS WITH OLIVES - HOLLOW SCREW FITTINGS AND RING CONNECTION FITTINGS FOR USE WITH UNION NUTS |
| DIN 7976:1990-08 | HEXAGON HEAD TAPPING SCREWS |
| DIN 7971:1990-08 | SLOTTED PAN HEAD TAPPING SCREWS |
| DIN 6924:1987-07 | PREVAILING TORQUE TYPE HEXAGON NUTS NON-METALLIC INSERT |
| DIN 7981:1990-08 | CROSS RECESSED PAN HEAD TAPPING SCREWS |
| DIN 975:1986-09 | THREADED RODS |
| DIN 7991:1986-01 | HEXAGON SOCKET COUNTERSUNK HEAD CAP SCREWS |
| DIN 71805:1990-11 | ANGLE JOINTS - HOUSINGS, CIRCLIPS |
| DIN 976 : DRAFT 93 S/S | STUD BOLTS |
| DIN 125-1:1990-03 | PRODUCT GRADE A WASHERS WITH A HARDNESS UP TO 250 HV, DESIGNED FOR USE WITH HEXAGON HEAD BOLTS AND NUTS |
| DIN 963:1990-08 | SLOTTED COUNTERSUNK (FLAT) HEAD SCREWS |
| DIN 3404:1988-01 | LUBRICATING NIPPLES - BUTTON HEAD |
| DIN 427:1986-09 | SLOTTED HEADLESS SCREWS WITH CHAMFERED END |
| DIN 84:1990-08 | SLOTTED CHEESE HEAD SCREWS; PRODUCT GRADE A |
| DIN 85:1990-08 | SLOTTED PAN HEAD SCREWS; PRODUCT GRADE A |
| DIN 80705:1990-08 | THIN NUTS WITH COARSE PITCH AND FINE PITCH THREAD AND WITH SMALL WIDTHS ACROSS FLATS |
| DIN 71802:1992-04 | BALL JOINTS WITH OR WITHOUT CIRCLIPS |
| DIN 3405:1986-05 | LUBRICATING NIPPLES CUPPED TYPE |
| DIN 6798:1988-07 | SERRATED LOCK WASHERS |
| DIN 71803:1988-07 | ANGLE JOINTS WITH SCREW STUDS - WITH RIVET STUDS |
| DIN 8919:1993-10 (Draft) | REFRIGERATION; REFRIGERANT CONTROL AND FILLING VALVES FOR CONNECTION TO REFRIGERATION FLARE TYPE FITTINGS MWP 40 |
| DIN 5586:1989-02 | Compressed air equipment for rail vehicles; locking screws with collar and vent |
| DIN 25192:1978-05 | T-HEAD BOLTS (HAMMER HEAD BOLTS), FOR RAILWAY VEHICLES |
| DIN 7337:1991-08 | BLIND RIVETS WITH BREAK MANDREL |
| DIN 7973:1990-08 | SLOTTED RAISED COUNTERSUNK HEAD TAPPING SCREWS |
| DIN 71433:1989-11 | COMPRESSION COUPLINGS WITH OLIVES - T-FITTINGS AND ELBOW FITTINGS FOR USE WITH UNION NUTS |
| DIN 6797:1988-07 | TOOTHED LOCK WASHERS |
| DIN 267-4:1983-08 | FASTENERS - TECHNICAL DELIVERY CONDITIONS - PROPERTY CLASSES FOR NUTS (PREVIOUS CLASSES) |
| DIN 13-13:1983-10 | ISO METRIC SCREW THREADS - SELECTED SIZES FOR SCREWS, BOLTS AND NUTS FROM 1 TO 52 MM SCREW THREAD DIAMETER AND LIMITS OF SIZES |
| DIN 50941 : LATEST | KORROSIONSSCHUTZ; CHROMATIEREN VON GALVANISCHEN ZINK- UND CADMIUMUEBERZUEGEN, ALLGEMEINE HINWEISE, KURZZEICHEN UND PRUEFVERFAHREN |
| DIN ISO 898-2:1981-03 | MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES |
| DIN ISO 898-1:1989-01 | MECHANICAL PROPERTIES OF FASTENERS - BOLTS, SCREWS AND STUDS |
| DIN 13-12:1988-10 | ISO METRIC SCREW THREADS - 1 MM TO 300 MM DIAMETER COARSE AND FINE PITCH THREADS - SELECTED DIAMETERS AND PITCHES |
| DIN 13-15:1982-08 | ISO METRIC SCREW THREADS - FUNDAMENTAL DEVIATIONS AND TOLERANCES FOR SCREW THREADS FROM 1 MM NOMINAL DIAMETER AND LARGER |
| DIN 13-2:1999-11 | ISO general purpose metric screw threads - Part 2: Nominal sizes for 0,2 mm, 0,25 mm and 0,35 mm fine pitch threads; nominal diameter from 1 mm to 50 mm |
| DIN 50950:1984-10 | MEASUREMENT OF COATING THICKNESS; MICROSCOPIC MEASUREMENT OF COATING THICKNESS; CROSS SECTION METHOD |
| DIN 13-14:1982-08 | ISO METRIC SCREW THREADS - BASIS OF THE TOLERANCE SYSTEM FOR SCREW THREADS 1 MM NOMINAL DIAMETER AND LARGER |
| DIN 50933:2015-08 | MEASUREMENT OF COATING THICKNESSES - MEASUREMENT OF THE THICKNESS OF COATINGS BY DIFFERENCE MEASUREMENT USING A STYLUS INSTRUMENT |
| DIN 267-1:1982-08 | FASTENERS - TECHNICAL DELIVERY CONDITIONS - GENERAL REQUIREMENTS |
| DIN 50955:1983-12 | MEASUREMENT OF COATING THICKNESSES; MEASUREMENT OF THICKNESS OF METALLIC COATINGS BY LOCAL ANODIC DISSOLUTION; COULOMETRIC METHOD |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.