• There are no items in your cart

DIN EN 1319:2010-06

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

DOMESTIC GAS-FIRED FORCED CONVECTION AIR HEATERS FOR SPACE HEATING, WITH FAN-ASSISTED BURNERS NOT EXCEEDING A NET HEAT INPUT OF 70 KW
Available format(s)

Hardcopy , PDF

Superseded date

03-07-2021

Language(s)

English

Published date

01-01-2010

Foreword
1 Scope
2 Normative references
3 Definitions
  3.1 Appliance and its constituent parts
  3.2 Adjusting, control and safety devices
  3.3 Operation of the appliance
  3.4 Gases
  3.5 Conditions of operation and measurement
  3.6 Classification
4 Construction and design requirements
  4.1 General
  4.2 Adjusting, control and safety devices
  4.3 Ignition devices
  4.4 Flame supervision system
  4.5 Start-gas flame establishment
  4.6 Main flame establishment
  4.7 Main burner
  4.8 Facility for remote control
  4.9 Thermostats and control of air temperature
  4.10 Gas pressure test points
5 Operational requirements
  5.1 Safety of operation
  5.2 Efficiency
6 Test methods
  6.1 General
  6.2 Construction and design
  6.3 Safety of operation
  6.4 Efficiency
7 Marking and instructions
  7.1 Marking of the appliance
  7.2 Marking of the packaging
  7.3 Utilization of symbols on the appliance and
       packaging
  7.4 Instructions
Table 1 - Classification of gases
Table 2 - Valving requirements
Table 3 - Characteristics of the test gases
Table 4 - Calorific values of the test gases of the third
          party
Table 5 - Test gases corresponding to the appliance
          categories
Table 6 - Test pressures
Table 7 - V[CO2,N], values
Table 8 - Accuracy of measurement
Table 9 - Gas type symbols
Table A.1.1 - Single categories marketed
Table A.1.2 - Double categories marketed
Table A.2 - Normal supply pressures
Table A.3 - Test gas corresponding to categories marketed
            nationally or locally
Table A.4
Table A.5 - Inlet connections permitted
Table A.6
Table D.1
Table ZA.1 - Identification form on the compliance of EN 1319
             with the essential requirements of the EU
             Directive 90/396/EEC on the approximation of the
             laws of Member States concerning gas appliances
Figure 1 - Examples of typical valve systems (4.2.8.2)
Figure 2 - Test of an appliance under abnormal draught
           conditions (6.3.5.1.4.1, 6.3.6.4.1)
Figure 3 - Test apparatus for type C1 appliances (6.3.5.1.4.3)
Figure 4 - Test apparatus for type C3 appliances - Flat roof
           (6.3.5.1.4.4)
Figure 5 - Test apparatus for type C3 appliances - angled roof
           (6.3.5.1.4.4)
Figure 6 - C6 test duct system (6.1.6.2.5)
Figure 7 - C6 test duct system - Position of restrictor
           (6.1.6.2.5; 6.3.5.2.1)
Figure 8 - C6 test duct system - Detail of restrictor
           (6.1.6.2.5)
Figure 9 - C6 test duct system for recirculation test
           (6.3.6.4.6.1)
Figure 10 - Positions of sensors for overheat protection
            test (6.3.7)
Figure 11 - Test apparatus for combustion products discharge
            safety device (type B12BS, B13BS and B14BS
            appliances; 6.3.10.4)
Figure 12 - Sampling probe for C6 appliances (6.3.6.2)
Figure 13 - Sampling probe for type B12, B13, B14, C32 and C33
            appliances with an outlet diameter of 100 mm or
            more (6.4.2)
Figure 14 - Location of the sampling probe for type B12, B13,
            B14, C32 and C33 appliances with an outlet
            diameter of 100 mm or more (6.4.2)
Figure 15 - Sampling probe for type B12, B13, B14, C32 and
            C33 appliances with an outlet diameter of less
            than 100 mm (6.4.2)
Figure 16 - Sampling probe for type C12 and C13 appliances
            (6.4.2)
Figure 17 - Location of the probe for type C12 and C13
            appliances (6.4.2)
Figure 18 - Mean specific heat of dry products of combustion
            (6.4.5)
Figure C.1 - Maximum permitted recirculation of the
             combustion products
Figure C.2 - Recycling device for pressure loss test (see
             C.2.1)
Figure C.3 - Relationship of terminal and wind direction for
             wind test (C.2.5)
Annex A (informative) National situations
Annex B (informative) Equivalence rules
Annex C (normative) Requirements and tests for the ducting of
                    C6 appliances
Annex D (informative) Means of identification of the various
                      types of gas in force in the various
                      countries
Annex E (informative) A-deviations
Annex F (normative) Special national conditions
Annex ZA (informative) Clauses of this European Standard
                       addressing requirements of provisions
                       of EU Directives

Defines the requirements and test methods for the safety and efficiency of domestic gas-fired air heaters with a fan to assist the transportation of combustion air and/or combustion products, hereafter referred to as appliances.

DocumentType
Standard
Pages
156
PublisherName
German Institute for Standardisation (Deutsches Institut für Normung)
Status
Superseded

Standards Relationship
SN EN 1319 : 2010 Identical
UNI EN 1319 : 2010 Identical
NF EN 1319 : 2010 Identical
BS EN 1319:2009 Identical
NS EN 1319 : 2009 Identical
NBN EN 1319 : 2010 Identical
I.S. EN 1319:2009 Identical
UNE-EN 1319:2010 Identical
EN 1319:2009 Identical
NEN EN 1319 : 2010 Identical

EN 1859:2009+A1:2013 Chimneys - Metal chimneys - Test methods
IEC 60335-2-102:2004+AMD1:2008+AMD2:2012 CSV Household and similar electrical appliances - Safety - Part 2-102:Particular requirements for gas, oil and solid-fuel burning appliances having electrical connections
IEC 60730-2-9:2015 RLV Automatic electrical controls - Part 2-9: Particular requirements for temperature sensing controls
ISO 7005-2:1988 Metallic flanges — Part 2: Cast iron flanges
ISO 6976:2016 Natural gas — Calculation of calorific values, density, relative density and Wobbe indices from composition
EN 10226-2:2005 Pipe threads where pressure tight joints are made on the threads - Part 2: Taper external threads and taper internal threads - Dimensions, tolerances and designation
EN 60584-2:1993 Thermocouples - Part 2: Tolerances
EN 60730-2-9:2010 Automatic electrical controls for household and similar use - Part 2-9: Particular requirements for temperature sensing controls
EN 12067-1 : 98 AMD 1 2003 GAS/AIR RATIO CONTROLS FOR GAS BURNERS AND GAS BURNING APPLIANCES - PART 1: PNEUMATIC TYPES
ISO 7005-3:1988 Metallic flanges Part 3: Copper alloy and composite flanges
EN ISO 1182:2010 Reaction to fire tests for products - Non-combustibility test (ISO 1182:2010)
EN ISO 3166-1:2014 Codes for the representation of names of countries and their subdivisions - Part 1: Country codes (ISO 3166-1:2013)
EN 161:2011+A3:2013 Automatic shut-off valves for gas burners and gas appliances
ISO 1182:2010 Reaction to fire tests for products Non-combustibility test
EN ISO 228-1:2003 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000)
EN 437:2003+A1:2009 Test gases - Test pressures - Appliance categories
EN 125:2010+A1:2015 Flame supervision devices for gas burning appliances - Thermoelectric flame supervision devices
EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
EN 126:2012 Multifunctional controls for gas burning appliances
EN 60584-1:2013 Thermocouples - Part 1: EMF specifications and tolerances
CR 1404:1994 Determination of emissions from appliances burning gaseous fuels during type-testing
IEC 60730-2-1:1989 Automatic electrical controls for household and similar use. Part 2: Particular requirements for electrical controls for electrical household appliances
EN 60335-2-102:2016 Household and similar electrical appliances - Safety - Part 2-102: Particular requirements for gas, oil and solid-fuel burning appliances having electrical connections
EN 60730-2-1 : 97 AMD 11 2005 AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PART 2-1: PARTICULAR REQUIREMENTS FOR ELECTRICAL CONTROLS FOR ELECTRICAL HOUSEHOLD APPLIANCES
ISO 9001:2015 Quality management systems — Requirements
ISO 3166-1:2013 Codes for the representation of names of countries and their subdivisions Part 1: Country codes
EN 60335-1:2012/A13:2017 HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED)
EN 298:2012 Automatic burner control systems for burners and appliances burning gaseous or liquid fuels
ISO 7005-1:2011 Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems
EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
EN ISO 6976:2016 Natural gas - Calculation of calorific values, density, relative density and Wobbe indices from composition (ISO 6976:2016)
EN 10226-1:2004 Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation
IEC 60584-1:2013 Thermocouples - Part 1: EMF specifications and tolerances
EN 88-1:2011+A1:2016 Pressure regulators and associated safety devices for gas appliances - Part 1: Pressure regulators for inlet pressures up to and including 50 kPa
ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
EN 257:2010 Mechanical thermostats for gas-burning appliances

View more information
US$338.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.