• There are no items in your cart

DIN EN 14140:2015-03

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE REFILLABLE WELDED STEEL CYLINDERS FOR LPG - ALTERNATIVE DESIGN AND CONSTRUCTION
Available format(s)

Hardcopy , PDF

Superseded date

03-07-2021

Language(s)

German

Published date

01-01-2015

National foreword
European foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and symbols
4 Materials
5 Design
6 Construction and workmanship
7 Tests and examinations
8 Technical requirements for type approval
9 Initial inspection and tests
10 Marking
11 Documentation
12 Certification
Annex A (normative) - Additional manufacturers markings
Annex B (informative) - Over-moulded cylinder
Annex C (informative) - Hot Air Balloon Cylinders
Annex D (informative) - Environmental checklist
Bibliography

Defines the minimum requirements for the design, construction and testing during manufacture of transportable refillable welded steel Liquefied Petroleum Gas (LPG) cylinders, of water capacity from 0,5 l up to and including 150 l, exposed to temperatures of -20 degrees C to +65 degrees C.

DocumentType
Standard
Pages
61
PublisherName
German Institute for Standardisation (Deutsches Institut für Normung)
Status
Superseded

ISO 17636-1:2013 Non-destructive testing of welds — Radiographic testing — Part 1: X- and gamma-ray techniques with film
ISO 11997-2:2013 Paints and varnishes — Determination of resistance to cyclic corrosion conditions — Part 2: Wet (salt fog)/dry/humidity/UV light
EN ISO 6520-1:2007 Welding and allied processes - Classification of geometric imperfections in metallic materials - Part 1: Fusion welding (ISO 6520-1:2007)
EN ISO 14021:2016 Environmental labels and declarations - Self-declared environmental claims (Type II environmental labelling) (ISO 14021:2016)
EN 10120:2017 Steel sheet and strip for welded gas cylinders
ISO 2812-2:2007 Paints and varnishes Determination of resistance to liquids Part 2: Water immersion method
ISO 6520-1:2007 Welding and allied processes Classification of geometric imperfections in metallic materials Part 1: Fusion welding
ISO 14245:2006 Gas cylinders Specifications and testing of LPG cylinder valves Self-closing
ISO 11114-1:2012 Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 1: Metallic materials
EN ISO 15613:2004 Specification and qualification of welding procedures for metallic materials - Qualification based on pre-production welding test (ISO 15613:2004)
EN ISO 6892-1:2016 Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016)
ISO 9712:2012 Non-destructive testing Qualification and certification of NDT personnel
EN ISO 3231:1997 Paints and varnishes - Determination of resistance to humid atmospheres containing sulfur dioxide (ISO 3231:1993)
EN ISO 5173:2010/A1:2011 DESTRUCTIVE TESTS ON WELDS IN METALLIC MATERIALS - BEND TESTS (ISO 5173:2009)
ISO 14732:2013 Welding personnel Qualification testing of welding operators and weld setters for mechanized and automatic welding of metallic materials
EN ISO 643:2012 Steels - Micrographic determination of the apparent grain size (ISO 643:2012)
ISO 14024:1999 Environmental labels and declarations Type I environmental labelling Principles and procedures
ISO 14021:2016 Environmental labels and declarations — Self-declared environmental claims (Type II environmental labelling)
ISO 6892-1:2016 Metallic materials Tensile testing Part 1: Method of test at room temperature
EN ISO 2409:2013 Paints and varnishes - Cross-cut test (ISO 2409:2013)
EN ISO 11117:2008/AC:2010 GAS CYLINDERS - VALVE PROTECTION CAPS AND VALVE GUARDS - DESIGN, CONSTRUCTION AND TESTS
ISO 9606-1:2012 Qualification testing of welders — Fusion welding — Part 1: Steels
EN ISO 11997-2:2013 Paints and varnishes - Determination of resistance to cyclic corrosion conditions - Part 2: Wet (salt fog)/dry/humidity/UV light (ISO 11997-2:2013)
ISO 11363-1:2010 Gas cylinders 17E and 25E taper threads for connection of valves to gas cylinders Part 1: Specifications
EN ISO 9227:2017 Corrosion tests in artificial atmospheres - Salt spray tests (ISO 9227:2017)
EN ISO 14732:2013 Welding personnel - Qualification testing of welding operators and weld setters for mechanized and automatic welding of metallic materials (ISO 14732:2013)
EN ISO 11114-1:2012/A1:2017 GAS CYLINDERS - COMPATIBILITY OF CYLINDER AND VALVE MATERIALS WITH GAS CONTENTS - PART 1: METALLIC MATERIALS (ISO 11114-1: 2012/AMD 1:2017)
ISO 5173:2009 Destructive tests on welds in metallic materials — Bend tests
EN ISO 9712:2012 Non-destructive testing - Qualification and certification of NDT personnel (ISO 9712:2012)
EN 1439:2017 LPG equipment and accessories - Procedure for checking transportable refillable LPG cylinders before, during and after filling
EN 10028-7:2016 Flat products made of steels for pressure purposes - Part 7: Stainless steels
EN ISO 19232-1:2013 Non-destructive testing - Image quality of radiographs - Part 1: Determination of the image quality value using wire-type image quality indicators (ISO 19232-1:2013)
ISO 15614-1:2017 Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys
EN ISO 19232-2:2013 Non-destructive testing - Image quality of radiographs - Part 2: Determination of the image quality value using step/hole-type image quality indicators (ISO 19232-2:2013)
EN 10272:2016 Stainless steel bars for pressure purposes
ISO 15609-1:2004 Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 1: Arc welding
EN ISO 17637:2016 Non-destructive testing of welds - Visual testing of fusion-welded joints (ISO 17637:2016)
ISO 4624:2016 Paints and varnishes — Pull-off test for adhesion
EN ISO 17639:2013 Destructive tests on welds in metallic materials - Macroscopic and microscopic examination of welds (ISO 17639:2003)
EN ISO 14025:2010 Environmental labels and declarations - Type III environmental declarations - Principles and procedures (ISO 14025:2006)
ISO 15995:2006 Gas cylinders Specifications and testing of LPG cylinder valves Manually operated
ISO 17636-2:2013 Non-destructive testing of welds — Radiographic testing — Part 2: X- and gamma-ray techniques with digital detectors
EN 1442:2017 LPG equipment and accessories - Transportable refillable welded steel cylinders for LPG - Design and construction
ISO 17639:2003 Destructive tests on welds in metallic materials Macroscopic and microscopic examination of welds
EN 10204:2004 Metallic products - Types of inspection documents
EN ISO 4624:2016 Paints and varnishes - Pull-off test for adhesion (ISO 4624:2016)
ISO 17637:2016 Non-destructive testing of welds Visual testing of fusion-welded joints
EN ISO 15609-1:2004 Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 1: Arc welding (ISO 15609-1:2004)
ISO 643:2012 Steels Micrographic determination of the apparent grain size
EN ISO 17636-2:2013 Non-destructive testing of welds - Radiographic testing - Part 2: X- and gamma-ray techniques with digital detectors (ISO 17636-2:2013)
ISO 19232-1:2013 Non-destructive testing — Image quality of radiographs — Part 1: Determination of the image quality value using wire-type image quality indicators
ISO 9227:2017 Corrosion tests in artificial atmospheres — Salt spray tests
ISO 14025:2006 Environmental labels and declarations — Type III environmental declarations — Principles and procedures
EN ISO 4136:2012 Destructive tests on welds in metallic materials - Transverse tensile test (ISO 4136:2012)
EN 14894:2013 LPG equipment and accessories - Cylinder and drum marking
ISO 19232-2:2013 Non-destructive testing — Image quality of radiographs — Part 2: Determination of the image quality value using step/hole-type image quality indicators
ISO 4136:2012 Destructive tests on welds in metallic materials Transverse tensile test
ISO 15613:2004 Specification and qualification of welding procedures for metallic materials Qualification based on pre-production welding test
ISO 2409:2013 Paints and varnishes Cross-cut test
EN ISO 17636-1:2013 Non-destructive testing of welds - Radiographic testing - Part 1: X- and gamma-ray techniques with film (ISO 17636-1:2013)
EN 14717:2005 Welding and allied processes - Environmental check list
EN ISO 9606-1:2017 Qualification testing of welders - Fusion welding - Part 1: Steels (ISO 9606-1:2012 including Cor 1:2012 and Cor 2:2013)
EN ISO 15995:2010 Gas cylinders - Specifications and testing of LPG cylinder valves - Manually operated (ISO 15995:2006)
ISO 11117:2008 Gas cylinders Valve protection caps and valve guards Design, construction and tests
ISO 3231:1993 Paints and varnishes — Determination of resistance to humid atmospheres containing sulfur dioxide
EN ISO 14245:2010 Gas cylinders - Specifications and testing of LPG cylinder valves - Self-closing (ISO 14245:2006)

View more information
US$162.29
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.