• There are no items in your cart

DIN EN 14276-1:2011-05

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 1: VESSELS - GENERAL REQUIREMENTS
Available format(s)

Hardcopy , PDF

Superseded date

11-03-2020

Language(s)

English, German

Published date

01-01-2011

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
  3.1 Definitions
  3.2 Symbols, quantities and units
4 Materials
  4.1 General
  4.2 Requirements for materials to be used for pressurised
       parts
  4.3 Requirements for materials
  4.4 Requirements for prevention of brittle fracture
  4.5 Material documentation
  4.6 Materials for non-pressure retaining parts
5 Pressure Vessel classification
  5.1 Category of vessel
  5.2 Fluid classification
6 Design
  6.1 General
  6.2 Corrosion and corrosion protection
  6.3 Stress corrosion cracking
  6.4 Loading
  6.5 Maximum allowable pressure PS
  6.6 Design pressure P[d]
  6.7 Calculation pressure P or P[c]
  6.8 Design temperature t[d]
  6.9 Minimum material temperature
  6.10 Calculation temperature t[c]
  6.11 Joint coefficient
  6.12 Design stress
  6.13 Access and inspection openings, venting and draining
       provisions, filling and discharge provisions and
       handling devices
  6.14 Methods for design
7 Manufacturing
  7.1 General
  7.2 Material traceability
  7.3 Manufacturing tolerances
  7.4 Permanent joints
  7.5 Forming of pressure parts
  7.6 Post weld heat treatment
  7.7 Internal cleanness
  7.8 Repairs/Reworks
  7.9 Finishing operations
8 Testing and inspection
  8.1 Performance of inspection and testing
  8.2 Design documentation, review and approval
  8.3 Type approval
  8.4 Calibration
  8.5 Material
  8.6 Manufacturing
  8.7 Non destructive testing
  8.8 Subcontracted elements
  8.9 Final inspection
  8.10 Marking
  8.11 Documentation
Annex A (normative) Alternative requirements for prevention
                       of brittle fracture: Method according to
                       temperature stress cases
Annex B (normative) Specification and approval of brazing
                       procedures, brazers and brazing operators
Annex C (normative) Pressure testing
Annex D (informative) Relations between the different pressures
Annex E (normative) Experimental methods
Annex F (normative) Material characteristics for design
Annex G (informative) Component classification in the sense of
                       the Pressure Equipment Directive (PED)
Annex H (informative) Selection of module of conformity
Annex I (normative) Grouping system for materials
Annex J (informative) DN System
Annex K (normative) Specification and approval of
                       expansion procedures and operators
Annex ZA (informative) Relationship between this European
                       Standard and the Essential
                       Requirements of EU Directive 97/23/EC
Bibliography

This standard is included in DIN Handbook 156/1.

DevelopmentNote
DRAFT 2017 issued in March 2017. (03/2017)
DocumentType
Standard
Pages
88
PublisherName
German Institute for Standardisation (Deutsches Institut für Normung)
Status
Superseded

DKI I 164 : 2017 KUPFERROHRE IN DER KAELTE-KLIMATECHNIK, FUER TECHNISCHE UND MEDIZINISCHE GASE
DIN HDBK 156/1 : 1ED 2008

ISO 17672:2016 Brazing Filler metals
EN 10269:2013 Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties
ISO 2553:2013 Welding and allied processes Symbolic representation on drawings Welded joints
EN ISO 5817:2014 Welding - Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) - Quality levels for imperfections (ISO 5817:2014)
EN 1045:1997 Brazing - Fluxes for brazing - Classification and technical delivery conditions
EN 1515-1:1999 Flanges and their joints - Bolting - Part 1: Selection of bolting
EN 13445-5 : 2014 COR 2017 UNFIRED PRESSURE VESSELS - PART 5: INSPECTION AND TESTING
ISO 3506-1:2009 Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs
EN 13445-6 : 2014 COR 2017 UNFIRED PRESSURE VESSELS - PART 6: REQUIREMENTS FOR THE DESIGN AND FABRICATION OF PRESSURE VESSELS AND PRESSURE PARTS CONSTRUCTED FROM SPHEROIDAL GRAPHITE CAST IRON
EN 378-4:2016 Refrigerating systems and heat pumps - Safety and environmental requirements - Part 4: Operation, maintenance, repair and recovery
EN ISO 6892-1:2016 Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016)
EN 10028-3:2017 Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized
CR 13445-7:2002 Unfired pressure vessels - Part 7: Guidance on the use of the conformity procedures
EN ISO 17672:2016 Brazing - Filler metals (ISO 17672:2016)
EN ISO 3506-1:2009 Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs (ISO 3506-1:2009)
EN ISO 15612:2004 Specification and qualification of welding procedures for metallic materials - Qualification by adoption of a standard welding procedure (ISO 15612:2004)
EN 378-1:2016 Refrigerating systems and heat pumps - Safety and environmental requirements - Part 1: Basic requirements, definitions, classification and selection criteria
EN 10164:2004 Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions
EN 378-3:2016 Refrigerating systems and heat pumps - Safety and environmental requirements - Part 3: Installation site and personal protection
ASME PV CODE 8 DIV 1 : 2017 BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 1
EN 12797:2000/A1:2003 BRAZING - DESTRUCTIVE TESTS OF BRAZED JOINTS
EN 10111:2008 Continuously hot rolled low carbon steel sheet and strip for cold forming - Technical delivery conditions
EN 764-1:2015+A1:2016 Pressure equipment - Part 1: Vocabulary
ISO 6892-1:2016 Metallic materials Tensile testing Part 1: Method of test at room temperature
EN 1005-2:2003+A1:2008 Safety of machinery - Human physical performance - Part 2: Manual handling of machinery and component parts of machinery
EN ISO 4063:2010 Welding and allied processes - Nomenclature of processes and reference numbers (ISO 4063:2009, Corrected version 2010-03-01)
EN ISO 15609-2:2001/A1:2003 SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - WELDING PROCEDURE SPECIFICATION - PART 2: GAS WELDING
EN 10216-2:2013 Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 2: Non-alloy and alloy steel tubes with specified elevated temperature properties
EN 764-5:2014 Pressure equipment - Part 5: Inspection documentation of metallic materials and compliance with the material specification
ISO 6708:1995 Pipework components Definition and selection of DN (nominal size)
EN 10025-1:2004 Hot rolled products of structural steels - Part 1: General technical delivery conditions
EN 10028-2:2017 Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties
EN 910 : 1996 DESTRUCTIVE TESTS ON WELDS IN METALLIC MATERIALS - BEND TESTS
EN 1653:1997/A1:2000 COPPER AND COPPER ALLOYS - PLATE, SHEET AND CIRCLES FOR BOILERS, PRESSURE VESSELS AND HOT WATER STORAGE UNITS
EN 13445-8 : 2014 COR 2017 UNFIRED PRESSURE VESSELS - PART 8: ADDITIONAL REQUIREMENTS FOR PRESSURE VESSELS OF ALUMINIUM AND ALUMINIUM ALLOYS
EN 10028-7:2016 Flat products made of steels for pressure purposes - Part 7: Stainless steels
ISO 15614-8:2016 Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 8: Welding of tubes to tube-plate joints
ISO 15612:2004 Specification and qualification of welding procedures for metallic materials Qualification by adoption of a standard welding procedure
EN 1173:2008 Copper and copper alloys - Material condition designation
ISO 5817:2014 Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) — Quality levels for imperfections
EN ISO 6708:1995 Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995)
EN ISO 3677:2016 Filler metal for soldering and brazing - Designation (ISO 3677:2016)
EN ISO 15611:2003 Specification and qualification of welding procedures for metallic materials - Qualification based on previous welding experience (ISO 15611:2003)
ISO 15614-1:2017 Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys
ISO 7438:2016 Metallic materials Bend test
EN 13445-4 : 2014 COR 2017 UNFIRED PRESSURE VESSELS - PART 4: FABRICATION
ISO 15609-1:2004 Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 1: Arc welding
ISO 15611:2003 Specification and qualification of welding procedures for metallic materials — Qualification based on previous welding experience
ISO 3677:2016 Filler metal for soldering and brazing — Designation
EN 22553:1994 Welded, brazed and soldered joints - Symbolic representation on drawings (ISO 2553:1992)
ISO 857-1:1998 Welding and allied processes Vocabulary Part 1: Metal welding processes
EN 12735-1:2016 Copper and copper alloys - Seamless, round tubes for air conditioning and refrigeration - Part 1: Tubes for piping systems
ISO 5187:1985 Welding and allied processes — Assemblies made with soft solders and brazing filler metals — Mechanical test methods
EN 10204:2004 Metallic products - Types of inspection documents
ISO 10012:2003 Measurement management systems — Requirements for measurement processes and measuring equipment
EN 10025-2:2004/AC:2005 HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR NON-ALLOY STRUCTURAL STEELS
EN ISO 15609-1:2004 Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 1: Arc welding (ISO 15609-1:2004)
EN 10130:2006 Cold rolled low carbon steel flat products for cold forming - Technical delivery conditions
ISO 15609-2:2001 Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 2: Gas welding
EN 764-2:2012 Pressure equipment - Part 2: Quantities, symbols and units
EN 12517-1:2006 Non-destructive testing of welds - Part 1: Evaluation of welded joints in steel, nickel, titanium and their alloys by radiography - Acceptance levels
EN ISO 10012:2003 Measurement management systems - Requirements for measurement processes and measuring equipment (ISO 10012:2003)
EN 837-1:1996/AC:1998 PRESSURE GAUGES - BOURDON TUBE PRESSURE GAUGES - DIMENSIONS, METROLOGY, REQUIREMENTS AND TESTING
ISO 4063:2009 Welding and allied processes — Nomenclature of processes and reference numbers
ISO 817:2014 Refrigerants Designation and safety classification
EN ISO 15614-8:2016 Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 8: Welding of tubes to tube-plate joints (ISO 15614-8:2016)
ISO 15607:2003 Specification and qualification of welding procedures for metallic materials General rules
EN 1418:1997 Welding personnel - Approval testing of welding operators for fusion welding and resistance weld setters for fully mechanized and automatic welding of metallic materials
EN 10160:1999 Ultrasonic testing of steel flat product of thickness equal or greater than 6 mm (reflection method)
EN 10025-3:2004 Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels
EN 764-3:2002 Pressure equipment - Part 3: Definition of parties involved
EN 12799:2000/A1:2003 BRAZING - NON-DESTRUCTIVE EXAMINATION OF BRAZED JOINTS
EN 378-2:2016 Refrigerating systems and heat pumps - Safety and environmental requirements - Part 2: Design, construction, testing, marking and documentation
EN 764-4:2014 Pressure equipment - Part 4: Establishment of technical delivery conditions for metallic materials
EN 12451:2012 Copper and copper alloys - Seamless, round tubes for heat exchangers
EN ISO 15607:2003 Specification and qualification of welding procedures for metallic materials - General rules (ISO 15607:2003)
1997/23/EC : 1997 DIRECTIVE 97/23/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 29 MAY 1997 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING PRESSURE EQUIPMENT
EN 287-1:2011 Qualification test of welders - Fusion welding - Part 1: Steels
EN ISO 7438:2016 Metallic materials - Bend test (ISO 7438:2016)

View more information
US$239.03
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.