DIN EN 15088 E : 2006
Current
The latest, up-to-date edition.
Hardcopy , PDF
English
01-01-2006
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
4.1 Ordering Information
4.2 Selection of alloy and temper
4.3 Product requirements
5 Evaluation of conformity
5.1 General
5.2 Testing
5.3 Factory production control (FPC)
5.4 One-off products, prototypes and products
produced in very small quantities
6 Marking, labelling and packaging
Annex A (normative) Fatigue testing and design
of extruded, rolled or forged products
A.1 General
A.2 Fatigue testing of the constituent
material (extruded, rolled or forged
products)
A.3 Test piece for fatigue testing
A.4 Design code
Annex B (normative) Bendability
B.1 General
B.2 Bendability classes
B.3 Assignment to standardized tempers of
semi-finished products
Annex ZA (informative) Clauses of this European
Standard addressing the provisions of
EU Construction Products Directive CPD -
EU Directive 89/106/EEC
ZA.1 Scope and relevant characteristics
ZA.2 Procedures for the attestation of
conformity of structural metallic
construction products
ZA.3 CE marking and labelling
Bibliography
Describes the requirements for semi-finished products and castings of aluminium and aluminium alloys for load-bearing structural construction works (Construction works covers building and civil engineering works).
| DocumentType |
Standard
|
| Pages |
31
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Current
|
| Standards | Relationship |
| EN 15088:2005 | Identical |
| BS EN 15088:2005 | Identical |
| UNE-EN 15088:2006 | Identical |
| NEN EN 15088 : 2006 | Identical |
| UNI EN 15088 : 2006 | Identical |
| I.S. EN 15088:2006 | Identical |
| NF EN 15088 : 2006 | Identical |
| SN EN 15088 : 2006 | Identical |
| NBN EN 15088 : 2006 | Identical |
| NS EN 15088 : 1ED 2006 | Identical |
| EN 1301-2:2008 | Aluminium and aluminium alloys - Drawn wire - Part 2: Mechanical properties |
| EN 485-1:2016 | Aluminium and aluminium alloys - Sheet, strip and plate - Part 1: Technical conditions for inspection and delivery |
| EN 755-1:2016 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 1: Technical conditions for inspection and delivery |
| EN 754-3:2008 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 3: Round bars, tolerances on dimensions and form |
| EN 754-7:2016 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 7: Seamless tubes, tolerances on dimensions and form |
| EN 755-5:2008 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 5: Rectangular bars, tolerances on dimensions and form |
| EN 1301-1:2008 | Aluminium and aluminium alloys - Drawn wire - Part 1: Technical conditions for inspection and delivery |
| EN 485-3:2003 | Aluminium and aluminium alloys - Sheet, strip and plate - Part 3: Tolerances on dimensions and form for hot-rolled products |
| EN 755-9:2016 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 9: Profiles, tolerances on dimensions and form |
| EN 485-2:2016 | ALUMINIUM AND ALUMINIUM ALLOYS - SHEET, STRIP AND PLATE - PART 2: MECHANICAL PROPERTIES |
| EN 485-4:1993 | Aluminium and aluminium alloys - Sheet, strip and plate - Part 4: Tolerances on shape and dimensions for cold-rolled products |
| EN 755-3:2008 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 3: Round bars, tolerances on dimensions and form |
| 89/106/EEC : 1988 | COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS |
| EN 1592-1:1997 | Aluminium and aluminium alloys - HF seam welded tubes - Part 1: Technical conditions for inspection and delivery |
| EN 586-2:1994 | Aluminium and aluminium alloys - Forgings - Part 2: Mechanical properties and additional property requirements |
| EN 13920-1:2003 | Aluminium and aluminium alloys - Scrap - Part 1: General requirements, sampling and tests |
| EN 755-8:2016 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 8: Porthole tubes, tolerances on dimensions and form |
| EN 1396:2015 | Aluminium and aluminium alloys - Coil coated sheet and strip for general applications - Specifications |
| EN 755-4:2008 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 4: Square bars, tolerances on dimensions and form |
| EN 586-3:2001 | Aluminium and aluminium alloys - Forgings - Part 3: Tolerances on dimensions and form |
| EN 755-7:2016 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 7: Seamless tubes, tolerances on dimensions and form |
| EN 12020-2:2016/AC:2017 | ALUMINIUM AND ALUMINIUM ALLOYS - EXTRUDED PRECISION PROFILES IN ALLOYS EN AW-6060 AND EN AW-6063 - PART 2: TOLERANCES ON DIMENSIONS AND FORM |
| EN 1301-3:2008 | Aluminium and aluminium alloys - Drawn wire - Part 3: Tolerances on dimensions |
| EN 754-6:2008 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 6: Hexagonal bars, tolerances on dimensions and form |
| EN 755-6:2008 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 6: Hexagonal bars, tolerances on dimensions and form |
| EN 12258-1:2012 | Aluminium and aluminium alloys - Terms and definitions - Part 1: General terms |
| PREN 1090-1 : DRAFT 2004 | STEEL AND ALUMINIUM STRUCTURAL COMPONENTS - GENERAL DELIVERY CONDITIONS |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| EN 1706:2010 | Aluminium and aluminium alloys - Castings - Chemical composition and mechanical properties |
| EN 754-1:2016 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 1: Technical conditions for inspection and delivery |
| EN 1559-1:2011 | Founding - Technical conditions of delivery - Part 1: General |
| EN 1592-4:1997 | Aluminium and aluminium alloys - HF seam welded tubes - Part 4: Tolerances on dimensions and form for square, rectangular and shaped tubes |
| EN 515:2017 | Aluminium and aluminium alloys - Wrought products - Temper designations |
| EN 754-5:2008 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 5: Rectangular bars, tolerances on dimensions and form |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| PREN 1090-3 : DRAFT 2017 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES |
| EN 586-1:1997 | Aluminium and aluminium alloys - Forgings - Part 1: Technical conditions for inspection and delivery |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN 754-8:2016 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 8: Porthole tubes, tolerances on dimensions and form |
| ISO 1519:2011 | Paints and varnishes Bend test (cylindrical mandrel) |
| EN 754-2:2016 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 2: Mechanical properties |
| EN ISO 1519:2011 | Paints and varnishes - Bend test (cylindrical mandrel) (ISO 1519:2011) |
| EN 1386:2007 | Aluminium and aluminium alloys - Tread plate - Specifications |
| EN 1999-1-2:2007/AC:2009 | EUROCODE 9 - DESIGN OF ALUMINIUM STRUCTURES - PART 1-2: STRUCTURAL FIRE DESIGN |
| EN 1592-2:1997 | Aluminium and aluminium alloys - HF seam welded tubes - Part 2: Mechanical properties |
| ENV 1999-1-2 : 1998 | EUROCODE 9: DESIGN OF ALUMINIUM STRUCTURES - GENERAL RULES - STRUCTURAL FIRE DESIGN |
| EN 1559-4:2015 | Founding - Technical conditions of delivery - Part 4: Additional requirements for aluminium alloy castings |
| EN 1592-3:1997 | Aluminium and aluminium alloys - HF seam welded tubes - Part 3: Tolerances on dimensions and form for circular tubes |
| EN 754-4:2008 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 4: Square bars, tolerances on dimensions and form |
| EN 573-3:2013 | Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products |
| EN 755-2:2016 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 2: Mechanical properties |
| EN 12020-1:2008 | Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 - Part 1: Technical conditions for inspection and delivery |
| ISO 8062:1994 | Castings System of dimensional tolerances and machining allowances |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.