DIN EN ISO 178 E : 2013
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010 + AMD.1:2013)
Available format(s)
Hardcopy , PDF
Superseded date
09-04-2019
Language(s)
English
Published date
01-01-2013
National foreword
National Annex NA (informative) - Bibliography
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Principle
5 Test machine
6 Test specimens
7 Atmosphere for conditioning and testing
8 Procedure
9 Calculation and expression of results
10 Precision
11 Test report
Annex A (informative) - Precision statement
Annex B (informative) - Influence of changes in test
speed on the measured values of flexural properties
Bibliography
Describes a method for determining the flexural properties of rigid and semi-rigid plastics under defined conditions.
| DevelopmentNote |
Supersedes DIN 53452 E and DIN 53457 E (08/2002)
|
| DocumentType |
Standard
|
| Pages |
27
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| UNI EN ISO 178 : 2013 | Identical |
| NS EN ISO 178 : 2010 AMD 1 2013 | Identical |
| EN ISO 178:2010/A1:2013 | Identical |
| ISO 178:2010 | Identical |
| SN EN ISO 178 : 2011 AMD 1 2013 | Identical |
| NF EN ISO 178 : 2011 AMD 1 2013 | Identical |
| BS EN ISO 178 : 2010 | Identical |
| ONORM EN ISO 178 : 2013 | Identical |
| I.S. EN ISO 178:2010 | Identical |
| NBN EN ISO 178 : 2011 AMD 1 2013 | Identical |
| NEN EN ISO 178 : 2010 AMD 1 2013 | Identical |
| EN ISO 178:2019 | Identical |
| DIN EN ISO 25137-2 E : 2017 | PLASTICS - SULFONE POLYMER MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 25137-2:2009) |
| DIN EN ISO 20753 E : 2014 | PLASTICS - TEST SPECIMENS (ISO 20753:2008) |
| DIN EN ISO 3673-2 E : 2012 | PLASTICS - EPOXY RESINS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES OF CROSSLINKED EPOXY RESINS (ISO 3673-2:2012) |
| DIN EN ISO 3672-2:2002-07 | PLASTICS - UNSATURATED-POLYESTER RESINS (UP-R) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN EN ISO 17855-2 E : 2016 | PLASTICS - POLYETHYLENE (PE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 17855-2:2016) |
| DIN ISO 11040-4 E : 2017 | PREFILLED SYRINGES - PART 4: GLASS BARRELS FOR INJECTABLES AND STERILIZED SUBASSEMBLED SYRINGES READY FOR FILLING (ISO 11040-4:2015) |
| DIN EN 12864 E : 2006 AMD 3 2010 | LOW PRESSURE, NON ADJUSTABLE REGULATORS HAVING A MAXIMUM OUTLET PRESSURE OF LESS THAN OR EQUAL TO 200 MBAR, WITH A CAPACITY OF LESS THAN OR EQUAL TO 4 KG/H, AND THEIR ASSOCIATED SAFETY DEVICES FOR BUTANE, PROPANE OR THEIR MIXTURES |
| DIN EN ISO 11833-1:2012-11 | PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE) SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS - PART 1: SHEETS OF THICKNESS NOT LESS THAN 1 MM (ISO 11833-1:2012) |
| DIN 16833:2009-09 | Pipes of raised-temperature-resistance polyethylene (PE-RT) - PE-RT Type I and PE-RT Type II - General quality requirements, testing |
| DIN 28090-3:2014-11 | STATIC GASKETS FOR FLANGE CONNECTIONS - GASKETS MADE FROM SHEETS - PART 3: CHEMICAL RESISTANCE TEST PROCEDURES |
| DIN EN ISO 12215-5:2014-10 | SMALL CRAFT - HULL CONSTRUCTION AND SCANTLINGS - PART 5: DESIGN PRESSURES FOR MONOHULLS, DESIGN STRESSES, SCANTLINGS DETERMINATION (ISO 12215-5:2008 + AMD 1:2014) |
| DIN EN ISO 9988-2 E : 2015 | PLASTICS - POLYOXYMETHYLENE (POM) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 9988-2:2006) |
| DIN EN ISO 3672-2 E : 2002 | PLASTICS - UNSATURATED-POLYESTER RESINS (UP-R) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN EN ISO 20028-2 E : 2017 | PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 20028-2:2017) |
| DIN EN ISO 14910-2 E : 2013 | PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 14910-2:2013) |
| DIN EN ISO 19069-2 E : 2016 | PLASTICS - POLYPROPYLENE (PP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 19069-2:2016) |
| DIN EN ISO 80369-7 E : 2017 | SMALL-BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 7: CONNECTORS FOR INTRAVASCULAR OR HYPODERMIC APPLICATIONS (ISO 80369-7:2016, CORRECTED VERSION 2016-12-01) |
| DIN EN ISO 80369-7:2017-10 | Small-bore connectors for liquids and gases in healthcare applications - Part 7: Connectors for intravascular or hypodermic applications (ISO 80369-7:2016, Corrected version 2016-12-01) |
| DIN EN ISO 14910-2:2013-06 | PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 14910-2:2013) |
| DIN ISO 11040-4:2017-07 | PREFILLED SYRINGES - PART 4: GLASS BARRELS FOR INJECTABLES AND STERILIZED SUBASSEMBLED SYRINGES READY FOR FILLING (ISO 11040-4:2015) |
| ISO 10350-2:2011 | Plastics Acquisition and presentation of comparable single-point data Part 2: Long-fibre-reinforced plastics |
| ISO 293:2004 | Plastics — Compression moulding of test specimens of thermoplastic materials |
| ISO 23529:2016 | Rubber General procedures for preparing and conditioning test pieces for physical test methods |
| DIN EN ISO 9513 E : 2013 | METALLIC MATERIALS - CALIBRATION OF EXTENSOMETER SYSTEMS USED IN UNIAXIAL TESTING (ISO 9513:2012 + COR 1:2013) |
| ISO 295:2004 | Plastics — Compression moulding of test specimens of thermosetting materials |
| ISO 10350-1:2017 | Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials |
| ISO 10724-1:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| DIN EN ISO 295 E : 2004 | PLASTICS - COMPRESSION MOULDING TEST SPECIMENS OF THERMOSETTING MATERIALS |
| ISO 9513:2012 | Metallic materials — Calibration of extensometer systems used in uniaxial testing |
| ISO 2602:1980 | Statistical interpretation of test results Estimation of the mean Confidence interval |
| ISO 1209-2:2007 | Rigid cellular plastics Determination of flexural properties Part 2: Determination of flexural strength and apparent flexural modulus of elasticity |
| ISO 472:2013 | Plastics Vocabulary |
| DIN EN ISO 291 E : 2008 | PLASTICS - STANDARD ATMOSPHERES FOR CONDITIONING AND TESTING |
| ISO 291:2008 | Plastics Standard atmospheres for conditioning and testing |
| ISO 14125:1998 | Fibre-reinforced plastic composites Determination of flexural properties |
| ISO 294-1:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens |
| ISO 7500-1:2015 | Metallic materials Calibration and verification of static uniaxial testing machines Part 1: Tension/compression testing machines Calibration and verification of the force-measuring system |
| ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
| DIN EN ISO 293 E : 2005 | PLASTICS - COMPRESSION MOULDING TEST SPECIMENS OF THERMOPLASTIC MATERIALS |
| ISO 20753:2008 | Plastics Test specimens |
| ISO 16012:2015 | Plastics Determination of linear dimensions of test specimens |
| ISO 1209-1:2007 | Rigid cellular plastics Determination of flexural properties Part 1: Basic bending test |
US$115.16
Excluding Tax where applicable
USD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.