DIN EN ISO 19712-3 E : 2013

Add To Cart

Product Format

Table of Contents - (Show below) - (Hide below)

National foreword National Annex NA (informative) - Bibliography Foreword Introduction 1 Scope 2 Normative references 3 Terms and definitions 4 Cleaning the test specimen surface 5 Surface defects 6 Resistance to impact by large-diameter ball 7 Lightfastness 8 Stain/chemical-resistance test 9 Resistance to cigarette burns 10 Resistance to dry heat 11 Resistance to wet heat 12 Hot/cold-cycle water-resistance test 13 Hardness 14 Ability to be renewed Bibliography

Abstract - (Show below) - (Hide below)

Describes the methods of test for determination of the properties of solid surfacing materials, as defined in Clause 3, in the form of shaped products.

General Product Information - (Show below) - (Hide below)

Published
Document Type	Standard
Status	Current
Publisher	German Institute for Standardisation (Deutsches Institut für Normung)
Pages
ISBN

International Equivalents – Equivalent Standard(s) & Relationship - (Show below) - (Hide below)

Equivalent Standard(s)	Relationship
ISO 19712-3 : 2007(R2015)	Identical
EN ISO 19712-3 : 2013	Identical
ISO 19712-3 : 2007(R2015)	Identical

Standards Referenced By This Book - (Show below) - (Hide below)

DIN EN ISO 19712-1 E : 2013	PLASTICS - DECORATIVE SOLID SURFACING MATERIALS - PART 1: CLASSIFICATION AND SPECIFICATIONS (ISO 19712-1:2008)

Standards Referencing This Book - (Show below) - (Hide below)

ISO 4892-1 : 2016	PLASTICS - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES - PART 1: GENERAL GUIDANCE
ISO 19712-1 : 2008(R2016)	PLASTICS - DECORATIVE SOLID SURFACING MATERIALS - PART 1: CLASSIFICATION AND SPECIFICATIONS
ISO 209 : 2007(R2016)	ALUMINIUM AND ALUMINIUM ALLOYS - CHEMICAL COMPOSITION
ISO 4211 : 1979(R2017)	FURNITURE - ASSESSMENT OF SURFACE RESISTANCE TO COLD LIQUIDS
DIN EN ISO 4892-1 E : 2001	PLASTICS - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES - PART 1: GENERAL GUIDANCE (ISO 4892-1:2016)
ISO 4892 : 1981	PLASTICS - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES
ISO 2039-1 : 2001(R2015)	PLASTICS - DETERMINATION OF HARDNESS - PART 1: BALL INDENTATION METHOD
DIN EN ISO 3668 E : 2001	PAINTS AND VARNISHES - VISUAL COMPARISON OF THE COLOUR OF PAINTS
ISO 3668 : 2017	PAINTS AND VARNISHES - VISUAL COMPARISON OF COLOUR OF PAINTS
ASTM D 2583 : 2013-03	TEST METHOD FOR INDENTATION HARDNESS OF RIGID PLASTICS BY MEANS OF A BARCOL IMPRESSOR
DIN EN ISO 2039-1 E : 2003	PLASTICS - DETERMINATION OF HARDNESS - PART 1: BALL INDENTATION METHOD
ISO 2039-2 : 1987(R2015)	PLASTICS - DETERMINATION OF HARDNESS - PART 2: ROCKWELL HARDNESS
ASTM D 2244 : 2016 : REDLINE	Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
EN 13310 : 2015	KITCHEN SINKS - FUNCTIONAL REQUIREMENTS AND TEST METHODS
DIN EN ISO 4892-2 E : 2013	PLASTICS - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES - PART 2: XENON-ARC LAMPS (ISO 4892-2:2013)
DIN EN ISO 2039-2 E : 2000	PLASTICS - DETERMINATION OF HARDNESS - PART 2: ROCKWELL HARDNESS
NEMA LD 3 : 2005	HIGH-PRESSURE DECORATIVE LAMINATES
ISO 4892-2 : 2013(R2018)	PLASTICS - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES - PART 2: XENON-ARC LAMPS
ISO 105-A02 : 1993(R2014)	TEXTILES - TESTS FOR COLOUR FASTNESS - PART A02: GREY SCALE FOR ASSESSING CHANGE IN COLOUR
ISO 9370 : 2017	PLASTICS - INSTRUMENTAL DETERMINATION OF RADIANT EXPOSURE IN WEATHERING TESTS - GENERAL GUIDANCE AND BASIC TEST METHOD
ANSI Z124.6 : 2007	PLASTIC SINKS
ISO 105-B02 : 2014	TEXTILES - TESTS FOR COLOUR FASTNESS - PART B02: COLOUR FASTNESS TO ARTIFICIAL LIGHT: XENON ARC FADING LAMP TEST

Publisher

Category