DIN EN ISO 20753 E : 2014
Current
Current
The latest, up-to-date edition.
PLASTICS - TEST SPECIMENS (ISO 20753:2008)
Published date
09-30-2014
National foreword
National Annex NA (informative) - Bibliography
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Preparation of test specimens
5 Types of test specimen and their dimensions
6 Report on preparation of test specimens
Annex A (informative) - Recommended applications
for multipurpose test specimens or parts
thereof
Annex B (normative) - Designation system for
test specimens
Bibliography
Defines dimensional requirements relating to test specimens prepared from plastics materials intended for processing by moulding, as well as to test specimens prepared by machining from sheets or shaped articles.
| DocumentType |
Standard
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Current
|
| Standards | Relationship |
| EN ISO 20753:2018 | Identical |
| EN ISO 20753:2014 | Identical |
| ISO 20753:2008 | Identical |
| DIN EN ISO 20028-2 E : 2017 | PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 20028-2:2017) |
| DIN EN ISO 17855-2 E : 2016 | PLASTICS - POLYETHYLENE (PE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 17855-2:2016) |
| DIN EN ISO 16396-2 E : 2017 | PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 16396-2:2017) |
| DIN EN ISO 19069-2 E : 2016 | PLASTICS - POLYPROPYLENE (PP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 19069-2:2016) |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| ISO 4589-3:2017 | Plastics — Determination of burning behaviour by oxygen index — Part 3: Elevated-temperature test |
| ISO 10350-2:2011 | Plastics Acquisition and presentation of comparable single-point data Part 2: Long-fibre-reinforced plastics |
| DIN EN ISO 11403-2 E : 2013 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 2: THERMAL AND PROCESSING PROPERTIES (ISO 11403-2:2012) |
| DIN EN ISO 604 E : 2003 | PLASTICS - DETERMINATION OF COMPRESSIVE PROPERTIES |
| ISO 22088-1:2006 | Plastics Determination of resistance to environmental stress cracking (ESC) Part 1: General guidance |
| ISO 293:2004 | Plastics — Compression moulding of test specimens of thermoplastic materials |
| ISO 3167:2014 | Plastics Multipurpose test specimens |
| VDE 0303-6 : 2007 COR 1 2010 | ELECTRICAL INSULATING MATERIALS - DETERMINATION OF ELECTROLYTIC CORROSION CAUSED BY INSULATING MATERIALS - TEST METHODS |
| ISO 294-5:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 5: Preparation of standard specimens for investigating anisotropy |
| ISO 11403-3:2014 | Plastics Acquisition and presentation of comparable multipoint data Part 3: Environmental influences on properties |
| DIN EN 60426 : 2007 COR 1 2010 | ELECTRICAL INSULATING MATERIALS - DETERMINATION OF ELECTROLYTIC CORROSION CAUSED BY INSULATING MATERIALS - TEST METHODS |
| ISO 294-3:2002 | Plastics Injection moulding of test specimens of thermoplastic materials Part 3: Small plates |
| ISO 22088-2:2006 | Plastics Determination of resistance to environmental stress cracking (ESC) Part 2: Constant tensile load method |
| DIN EN ISO 11403-1 E : 2003 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 1: MECHANICAL PROPERTIES (ISO 11403-1:2014) |
| DIN EN ISO 11403-3 E : 2002 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 3: ENVIRONMENTAL INFLUENCES ON PROPERTIES (ISO 11403-3:2014) |
| DIN EN ISO 294-5 E : 2013 | PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - PART 5: PREPARATION OF STANDARD SPECIMENS FOR INVESTIGATING ANISOTROPY (ISO 294-5:2017) |
| ISO 295:2004 | Plastics — Compression moulding of test specimens of thermosetting materials |
| ISO 10350-1:2017 | Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials |
| ISO 22088-5:2006 | Plastics Determination of resistance to environmental stress cracking (ESC) Part 5: Constant tensile deformation method |
| ISO 2039-1:2001 | Plastics Determination of hardness Part 1: Ball indentation method |
| ISO 10724-1:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens |
| DIN EN ISO 306 E : 2014 | PLASTICS - THERMOPLASTIC MATERIALS - DETERMINATION OF VICAT SOFTENING TEMPERATURE (VST) (ISO 306:2013) |
| ISO 8256:2004 | Plastics — Determination of tensile-impact strength |
| ISO 11359-2:1999 | Plastics Thermomechanical analysis (TMA) Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature |
| VDE 0303-11 : 2010 | METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS |
| DIN EN ISO 178 E : 2013 | PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010 + AMD.1:2013) |
| DIN EN 60112 : 2010 | METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS |
| ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| DIN EN ISO 868 E : 2003 | PLASTICS AND EBONITE - DETERMINATION OF INDENTATION HARDNESS BY MEANS OF A DUROMETER (SHORE HARDNESS) |
| DIN EN ISO 2039-1 E : 2003 | PLASTICS - DETERMINATION OF HARDNESS - PART 1: BALL INDENTATION METHOD |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| DIN EN ISO 295 E : 2004 | PLASTICS - COMPRESSION MOULDING TEST SPECIMENS OF THERMOSETTING MATERIALS |
| ISO 2039-2:1987 | Plastics Determination of hardness Part 2: Rockwell hardness |
| ISO 11403-2:2012 | Plastics — Acquisition and presentation of comparable multipoint data — Part 2: Thermal and processing properties |
| ISO 180:2000 | Plastics Determination of Izod impact strength |
| ISO 22088-3:2006 | Plastics Determination of resistance to environmental stress cracking (ESC) Part 3: Bent strip method |
| ISO 294-2:1996 | Plastics Injection moulding of test specimens of thermoplastic materials Part 2: Small tensile bars |
| ISO 899-2:2003 | Plastics Determination of creep behaviour Part 2: Flexural creep by three-point loading |
| ISO 1183-1:2012 | Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method |
| ISO 1183-2:2004 | Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method |
| ISO 1183-3:1999 | Plastics Methods for determining the density of non-cellular plastics Part 3: Gas pyknometer method |
| ISO 604:2002 | Plastics — Determination of compressive properties |
| DIN EN ISO 4589-2 E : 2006 | PLASTICS - DETERMINATION OF BURNING BEHAVIOUR BY OXYGEN INDEX - PART 2: AMBIENT-TEMPERATURE TEST (ISO 4589-2:2017) |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| DIN EN ISO 2039-2 E : 2000 | PLASTICS - DETERMINATION OF HARDNESS - PART 2: ROCKWELL HARDNESS |
| IEC 60426:2007 | Electrical insulating materials - Determination of electrolytic corrosion caused by insulating materials - Test methods |
| ISO 306:2013 | Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST) |
| ISO 22088-4:2006 | Plastics Determination of resistance to environmental stress cracking (ESC) Part 4: Ball or pin impression method |
| ISO 294-1:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens |
| ISO 22088-6:2006 | Plastics Determination of resistance to environmental stress cracking (ESC) Part 6: Slow strain rate method |
| ISO 4589-2:2017 | Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test |
| ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
| ISO 899-1:2017 | Plastics — Determination of creep behaviour — Part 1: Tensile creep |
| DIN EN ISO 293 E : 2005 | PLASTICS - COMPRESSION MOULDING TEST SPECIMENS OF THERMOPLASTIC MATERIALS |
| ISO 11403-1:2014 | Plastics Acquisition and presentation of comparable multipoint data Part 1: Mechanical properties |
| DIN EN ISO 4589-3 E : 2017 | PLASTICS - DETERMINATION OF BURNING BEHAVIOUR BY OXYGEN INDEX - PART 3: ELEVATED-TEMPERATURE TEST (ISO 4589-3:2017) |
| ASTM D 1822 : 2013 : REDLINE | Standard Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials |
| ISO 178:2010 | Plastics Determination of flexural properties |
| ISO 868:2003 | Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness) |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.