• There are no items in your cart

DIN EN ISO 6185-3:2014-12

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

INFLATABLE BOATS - PART 3: BOATS WITH A HULL LENGTH LESS THAN 8 M WITH A MOTOR POWER RATING OF 15 KW AND GREATER (ISO 6185-3:2014)
Available format(s)

Hardcopy , PDF

Superseded date

06-03-2019

Language(s)

English, German

Published date

01-01-2014

National foreword
National Annex NA (informative) - Bibliography
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Structural Materials
6 Functional components
7 Safety requirements of the completed boat
8 Performance
9 Builder's plate(s)
10 Owner's manual
11 Standard equipment
Annex A (informative) - General arrangement
        of a typical Type VII boat
Annex B (informative) - General arrangement
        of a typical Type VIlI boat
Annex ZA (informative) - Relationship between
         this European Standard and the Essential
         Requirements of EU Directive 94/25/EC
         as amended by Directive 2003/44/EC
Bibliography

Defines the minimum safety characteristics required for the design, materials to use, manufacture and testing of inflatable boats and rigid inflatable boats with a hull length L[H] in accordance with ISO 8666 less than 8 m with a motor power rating of 15 kW and greater.

DocumentType
Standard
Pages
44
PublisherName
German Institute for Standardisation (Deutsches Institut für Normung)
Status
Superseded

BWB TL 1940-0012 : 5ED 2007
DIN EN ISO 6185-4:2011-10 INFLATABLE BOATS - PART 4: BOATS WITH A HULL LENGTH OF BETWEEN 8 M AND 24 M WITH A MOTOR POWER RATING OF 15 KW AND GREATER

ISO 10239:2014 Small craft Liquefied petroleum gas (LPG) systems
ISO 15083:2003 Small craft - Bilge-pumping systems
ISO 12215-5:2008 Small craft Hull construction and scantlings Part 5: Design pressures for monohulls, design stresses, scantlings determination
ISO 2896:2001 Rigid cellular plastics Determination of water absorption
ISO 11192:2005 Small craft Graphical symbols
ISO 7010:2011 Graphical symbols Safety colours and safety signs Registered safety signs
ISO 14946:2001 Small craft Maximum load capacity
DIN EN ISO 6185-4:2011-10 INFLATABLE BOATS - PART 4: BOATS WITH A HULL LENGTH OF BETWEEN 8 M AND 24 M WITH A MOTOR POWER RATING OF 15 KW AND GREATER
DIN ISO 3864-1:2012-06 Graphical symbols - Safety colours and safety signs - Part 1: Design principles for safety signs and safety markings (ISO 3864-1:2011)
DIN EN ISO 2411:2016-07 (Draft) RUBBER OR PLASTICS-COATED FABRICS - DETERMINATION OF COATING ADHESION (ISO 2411:2017)
ISO 4675:2017 Rubber- or plastics-coated fabrics — Low-temperature bend test
DIN EN ISO 15085:2009-10 SMALL CRAFT - MAN-OVERBOARD PREVENTION AND RECOVERY
ISO 12217-3:2015 Small craft — Stability and buoyancy assessment and categorization — Part 3: Boats of hull length less than 6 m
ISO 10088:2013 Small craft — Permanently installed fuel systems
ISO 11547:1994 Small craft — Start-in-gear protection
DIN EN ISO 11105:1997-07 SMALL CRAFT - VENTILATION OF PETROL ENGINE AND/OR PETROL TANK COMPARTMENTS
ISO 6185-4:2011 Inflatable boats Part 4: Boats with a hull length of between 8 m and 24 m with a motor power rating of 15 kW and greater
DIN EN ISO 16180:2013-07 SMALL CRAFT - NAVIGATION LIGHTS - INSTALLATION, PLACEMENT AND VISIBILITY (ISO 16180:2013)
ISO 2411:2017 Rubber- or plastics-coated fabrics — Determination of coating adhesion
ISO 11105:1997 Small craft Ventilation of petrol engine and/or petrol tank compartments
ISO 11592:2001 Small craft less than 8 m length of hull Determination of maximum propulsion power rating
ISO 8666:2016 Small craft Principal data
DIN EN ISO 10592:1995-06 Small craft - Hydraulic steering systems (ISO 10592:1994)
DIN EN ISO 12216:2002-10 SMALL CRAFT - WINDOWS, PORTLIGHTS, HATCHES, DEADLIGHTS AND DOORS - STRENGTH AND WATERTIGHTNESS REQUIREMENTS
DIN ISO 1817:2016-11 RUBBER, VULCANIZED OR THERMOPLASTIC - DETERMINATION OF THE EFFECT OF LIQUIDS (ISO 1817:2015)
DIN EN ISO 21487:2016-05 SMALL CRAFT - PERMANENTLY INSTALLED PETROL AND DIESEL FUEL TANKS (ISO 21487:2012 + AMD 1:2014 + AMD 2:2015)
ISO 8847:2004 Small craft Steering gear Cable and pulley systems
DIN EN ISO 10240:2015-09 SMALL CRAFT - OWNER'S MANUAL (ISO 10240:2004 + AMD 1:2015)
ISO 15084:2003 Small craft Anchoring, mooring and towing Strong points
ISO 9775:1990 Small craft Remote steering systems for single outboard motors of 15 kW to 40 kW power
ISO 10133:2012 Small craft Electrical systems Extra-low-voltage d.c. installations
ISO 8469:2013 Small craft Non-fire-resistant fuel hoses
ISO 12217-1:2015 Small craft — Stability and buoyancy assessment and categorization — Part 1: Non-sailing boats of hull length greater than or equal to 6 m
ISO 12215-3:2002 Small craft — Hull construction and scantlings — Part 3: Materials: Steel, aluminium alloys, wood, other materials
DIN EN ISO 10088:2013-12 Small craft - Permanently installed fuel systems (ISO 10088:2013)
DIN EN ISO 11812:2003-07 SMALL CRAFT - WATERTIGHT COCKPITS AND QUICK-DRAINING COCKPITS
ISO 8846:1990 Small craft — Electrical devices — Protection against ignition of surrounding flammable gases
ISO 8849:2003 Small craft Electrically operated direct-current bilge pumps
ISO 8848:1990 Small craft Remote steering systems
DIN EN ISO 10239:2015-05 SMALL CRAFT - LIQUEFIED PETROLEUM GAS (LPG) SYSTEMS (ISO 10239:2014)
ISO 16180:2013 Small craft — Navigation lights — Installation, placement and visibility
ISO 10592:1994 Small craft Hydraulic steering systems
ISO 15652:2003 Small craft Remote steering systems for inboard mini jet boats
ISO 11812:2001 Small craft Watertight cockpits and quick-draining cockpits
DIN EN ISO 8099:2015-11 (Draft) SMALL CRAFT - TOILET WASTE RETENTION SYSTEMS
ISO 12215-1:2000 Small craft — Hull construction and scantlings — Part 1: Materials: Thermosetting resins, glass-fibre reinforcement, reference laminate
ISO 10240:2004 Small craft Owner's manual
ISO 21487:2012 Small craft — Permanently installed petrol and diesel fuel tanks
ISO 3864-1:2011 Graphical symbols Safety colours and safety signs Part 1: Design principles for safety signs and safety markings
ISO 13297:2014 Small craft Electrical systems Alternating current installations
ISO 15085:2003 Small craft Man-overboard prevention and recovery
ISO 9094:2015 Small craft — Fire protection
EN 314-2:1993 Plywood - Bonding quality - Part 2: Requirements
DIN EN ISO 9094:2016-05 Small craft - Fire protection (ISO 9094:2015)
DIN EN 29775:1993-10 Small craft; remote steering systems for single outboard motors of 15 kW to 40 kW (ISO 9975:1990); German version EN 29975:1993
ISO 16147:2002 Small craft Inboard diesel engines Engine-mounted fuel and electrical components
ISO 15584:2001 Small craft Inboard petrol engines Engine-mounted fuel and electrical components
DIN EN ISO 4674-1:2015-04 (Draft) RUBBER- OR PLASTICS-COATED FABRICS - DETERMINATION OF TEAR RESISTANCE - PART 1: CONSTANT RATE OF TEAR METHODS (ISO 4674-1:2016)
DIN EN ISO 8666:2014-12 (Draft) SMALL CRAFT - PRINCIPAL DATA (ISO 8666:2016)
ISO 8665:2006 Small craft Marine propulsion reciprocating internal combustion engines Power measurements and declarations
ISO 12216:2002 Small craft Windows, portlights, hatches, deadlights and doors Strength and watertightness requirements
DIN EN ISO 12217-3:2016-03 SMALL CRAFT - STABILITY AND BUOYANCY ASSESSMENT AND CATEGORIZATION - PART 3: BOATS OF HULL LENGTH LESS THAN 6 M (ISO 12217-3:2015)
DIN EN ISO 7010:2012-10 GRAPHISCHE SYMBOLE - SICHERHEITSFARBEN UND SICHERHEITSZEICHEN - REGISTRIERTE SICHERHEITSZEICHEN (ISO 7010:2011/AMD 5:2014)
DIN EN ISO 13297:2015-04 SMALL CRAFT - ELECTRICAL SYSTEMS - ALTERNATING CURRENT INSTALLATIONS (ISO 13297:2014)
ISO 3011:1997 Rubber- or plastics-coated fabrics Determination of resistance to ozone cracking under static conditions
DIN EN ISO 10133:2013-04 Small craft - Electrical systems - Extra-low-voltage d.c. installations (ISO 10133:2012)
ISO 4674-1:2016 Rubber- or plastics-coated fabrics Determination of tear resistance Part 1: Constant rate of tear methods
ISO 10087:2006 Small craft Craft identification Coding system
ISO 12215-6:2008 Small craft — Hull construction and scantlings — Part 6: Structural arrangements and details
DIN EN ISO 12215-3:2002-09 SMALL CRAFT - HULL CONSTRUCTION AND SCANTLINGS - PART 3: MATERIALS: STEEL, ALUMINIUM ALLOYS, WOOD, OTHER MATERIALS
ISO 1817:2015 Rubber, vulcanized or thermoplastic Determination of the effect of liquids
ISO 14945:2004 Small craft Builder's plate
ISO 8099:2000 Small craft Toilet waste retention systems
DIN EN ISO 12217-1:2016-08 SMALL CRAFT - STABILITY AND BUOYANCY ASSESSMENT AND CATEGORIZATION - PART 1: NON-SAILING BOATS OF HULL LENGTH GREATER THAN OR EQUAL TO 6 M (ISO 12217-1:2015)

View more information
US$165.46
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.