DIN EN 10092-1:2004-01
|
Hot rolled spring steel flat bars - Part 1: Flat bars - Dimensions and tolerances on shape and dimensions; German version EN 10092-1:2003
|
DIN 1025-1:2009-04
|
Hot rolled I-sections - Part 1: Narrow flange I-sections, I-series - Dimensions, masses, sectional properties
|
DIN 59350:2008-06
|
PRECISION GROUND FLATS AND SQUARES - DIMENSIONS, MASS, TOLERANCES
|
DIN 488-2:2009-08
|
Reinforcing steels - Reinforcing steel bars
|
DIN 1026-2:2002-10
|
Hot-rolled steel channels with parallel flanges - Part 2: Dimensions, masses and static parameters
|
DIN 1027:2004-04
|
Bars made of hot rolled steel Zee sections with rounded roots adn toes - Dimensions, mass and static parameters
|
DIN 6880:2011-06
|
Bright key steel - Dimensions, tolerances, mass
|
DIN EN 10029:2011-02
|
Hot-rolled steel plates 3 mm thick or above - Tolerances on dimensions and shape
|
DIN 59370:2008-06
|
Bright steel sharp-edged equal leg angles - Dimensions, mass, tolerances on dimensions and shape
|
DIN EN 10210-2:2016-02 (Draft)
|
HOT FINISHED STRUCTURAL HOLLOW SECTIONS OF NON-ALLOY AND FINE GRAIN STEELS - PART 2: TOLERANCES, DIMENSIONS AND SECTIONAL PROPERTIES
|
DIN EN 10143:2006-09
|
Continuously hot-dip coated steel sheet and strip - Tolerances on dimensions and shape
|
DIN EN 10051:2011-02
|
Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels - Tolerances on dimensions and shape
|
DIN EN ISO 1127:1997-03
|
STAINLESS STEEL TUBES - DIMENSIONS, TOLERANCES AND CONVENTIONAL MASSES PER UNIT LENGTH
|
DIN 488-5:2009-08
|
Reinforcing steels - Lattice girders
|
DIN 1026-1:2009-09
|
Hot rolled steel channels - Part 1: Taper flange steel channels - Dimensions, masses and sectional properties
|
DIN EN ISO 18286:2010-11
|
Hot-rolled stainless steel plates - Tolerances on dimensions and shape (ISO 18286:2008)
|
DIN EN ISO 9444-2:2010-11
|
Continuously hot-rolled stainless steel - Tolerances on dimensions and form - Part 2: Wide strip and sheet/plate (ISO 9444-2:2009)
|
DIN EN 10092-2:2004-01
|
Hot rolled spring steel flat bars - Part 2: Ribbed and grooved spring leaves, Dimensions and tolerances on shape and dimensions; German version EN 10092-2:2003
|
DIN 488-4:2009-08
|
Reinforcing steels - Welded fabric
|
DIN 21530-2:2016-09
|
MINE SUPPORT - PART 2: DIMENSIONS, DESIGNATION AND STATICAL VALUES
|
DIN 488-3:2009-08
|
Reinforcing steels - Reinforcing steel in coils, steel wire
|
DIN EN 10056-1:2017-06
|
STRUCTURAL STEEL EQUAL AND UNEQUAL LEG ANGLES - PART 1: DIMENSIONS
|
DIN EN 10058:2004-02
|
HOT ROLLED FLAT STEEL BARS FOR GENERAL PURPOSES - DIMENSIONS AND TOLERANCES ON SHAPE AND DIMENSIONS
|
DIN EN 10220:2003-03
|
SEAMLESS AND WELDED STEEL TUBES - DIMENSIONS AND MASSES PER UNIT LENGTH
|
DIN 1022:2004-04
|
Bars made hot-rolled square-edged steel equal angles (LS-steel bars) - Dimensions and mass
|