• There are no items in your cart

EEMUA 190 : 2000

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

GUIDE FOR THE DESIGN, CONSTRUCTION AND USE OF MOUNDED HORIZONTAL CYLINDRICAL VESSELS FOR PRESSURISED STORAGE OF LPG AT AMBIENT TEMPERATURE
Available format(s)

Hardcopy , PDF

Superseded date

02-08-2021

Language(s)

English

Published date

01-01-2000

FOREWORD
1 INTRODUCTION AND SCOPE
2 TYPES OF STORAGE VESSEL
3 FOUNDATION AND EARTH MOUND
4 VESSEL
5 VESSEL: INSPECTION, TESTING
  AND CERTIFICATION
6 GUIDELINES FOR IN-SERVICE INSPECTION
7 REFERENCES
8 GLOSSARY OF ABBREVIATIONS
APPENDIX A - STRESS ANALYSIS OF MOUNDED
             STORAGE VESSELS
APPENDIX B - TYPICAL DESIGN FEATURES FOR
             VESSEL, FOUNDATION AND CONNECTIONS
APPENDIX C - DISTRIBUTION OF SOIL REACTION
             (SUPPORTING LOAD)
APPENDIX D - RECOMMENDED STEEL GRADES
APPENDIX E - PROJECT PLANNING
APPENDIX F - DELETED
APPENDIX G - NON-DESTRUCTIVE TESTING REQUIREMENTS
APPENDIX H - MATERIAL HARDNESS TESTING
APPENDIX I - SELECTION OF STORAGE SYSTEM

Specifies the main requirements for the successful design, construction, installation and use of mounded storage steel vessels, including: - criteria for selecting mounded storage - soil survey - foundation and mound design - vessel design and fabrication - erection and construction - requirements for operability (fittings, instrumentation) - corrosion protection - inspection and testing and - in-service monitoring, inspection and maintenance.

DevelopmentNote
Reprinted 2017 incorporating all amendments and errata to date. (08/2017)
DocumentType
Standard
Pages
108
PublisherName
Engineering Equipment Material Users Association
Status
Superseded
SupersededBy

EEMUA 147 : 2016 RECOMMENDATIONS FOR REFRIGERATED LIQUEFIED GAS STORAGE TANKS
EEMUA 217 : 2011 SAFE AND EFFECTIVE OPERATION OF STORAGE TANKS FOR OIL MOVEMENTS

ISO 8501-1:2007 Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings
ISO 9329-3:1997 Seamless steel tubes for pressure purposes — Technical delivery conditions — Part 3: Unalloyed and alloyed steels with specified low temperature properties
EN 10028-3:2017 Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized
EN 10164:2004 Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions
ISO 2808:2007 Paints and varnishes Determination of film thickness
ASME PV CODE 8 DIV 1 : 2017 BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 1
EN 1714:1997/A2:2003 NON-DESTRUCTIVE TESTING OF WELDS - ULTRASONIC TESTING OF WELDED JOINTS
ASTM A 516/A516M : 2017 : REDLINE Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service
ASTM A 350 : 2004 SPECIFICATION FOR FORGINGS, CARBON AND LOW ALLOY STEEL, REQUIRING NOTCH TOUGHNESS TESTING FOR PIPING COMPONENTS
NACE RP 02 74 : 2004 HIGH-VOLTAGE ELECTRICAL INSPECTION OF PIPELINE COATINGS
ASTM D 2167 : 2015 : REDLINE Standard Test Method for Density and Unit Weight of Soil in Place by the Rubber Balloon Method
EEMUA 159 : 2014 ABOVE GROUND FLAT BOTTOMED STORAGE TANKS - A GUIDE TO INSPECTION, MAINTENANCE AND REPAIR
BS EN 1993-1-1 : 2005 EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS
ISO 4624:2016 Paints and varnishes — Pull-off test for adhesion
BS 5400-3:1982 Steel, concrete and composite bridges Code of practice for design of steel bridges
BS 6072:1981 Method for magnetic particle flaw detection
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
EN 10222-4:2017 Steel forgings for pressure purposes - Part 4: Weldable fine grain steels with high proof strength
BS 3923-2:1972 Methods for ultrasonic examination of welds Automatic examination of fusion welded butt joints in ferritic steels
EEMUA 147 : 2016 RECOMMENDATIONS FOR REFRIGERATED LIQUEFIED GAS STORAGE TANKS
ISO 8503-1:2012 Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces
EN 10160:1999 Ultrasonic testing of steel flat product of thickness equal or greater than 6 mm (reflection method)
EN 1043-1:1995 Destructive tests on welds in metallic materials - Hardness testing - Part 1: Hardness test on arc welded joints
EN 1435:1997/A2:2003 NON-DESTRUCTIVE TESTING OF WELDS - RADIOGRAPHIC TESTING OF WELDED JOINTS
EN 287-1:2011 Qualification test of welders - Fusion welding - Part 1: Steels

View more information
US$177.28
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.