EN 10016-1:1994
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
07-01-2011
12-08-1994
Foreword
1 Scope
2 Normative references
3 Definitions
4 Classification and designation
5 Information to be supplied by the purchaser
6 Production process
7 Requirements
7.1 General
7.2 Quality assurance
7.3 Method of delivery
7.4 Delivery condition
8 Dimensions, mass and tolerances
9 Inspection
9.1 Inspection and inspection documents
9.2 Extension of inspection
9.3 Acceptance unit and number of samples and test
pieces
9.4 Test of chemical composition
9.5 Test of decarburization surface defects,
non-metallic inclusions and core segregation
9.6 Test methods
9.7 Invalidation of tests
9.8 Retests
9.9 Sorting or reprocessing
10 Marking
11 Complaints after delivery
Annex A (normative) Determination of core segregation
1.1 This European Standard is applicable to rod of non-alloy steel intended for wire drawing and/or cold rolling. The cross-section of the rod may be round, square, rectangular, hexagonal, half-round or another shape and as a general rule of nominal size 5 mm or above (see EURONORM 17) : the surface is smooth. 1.2 It is not applicable to following products for which standards exist or are under study such as : - steel rod intended for heat treatment (see EN 10083 and EURONORM 84, 85 and 86) ; - rod of free-cutting steels (see EURONORM 87) ; - steel rod for cold heading and cold extrusion (see EURONORM 119) ; - steel rod intended for the production of electrodes and products for welding (see EURONORM 133) ; - steel rod for welded fabric for reinforcement for concrete (see prENV 10080) ; - steel rod for wire for high fatique stength mechanical springs, such as valve springs. 1.3 In addition to the requirements of this standards the general technical delivery requirements specified in EN 10021 apply.
| Committee |
CEN/TC 459/SC 6
|
| DevelopmentNote |
Supersedes EURONORM 16 (11/2003)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NS EN 10016-1 : 1ED 1995 | Identical |
| UNI EN 10016-1 : 1996 | Identical |
| DIN EN 10016-1:1995-04 | Identical |
| NEN EN 10016-1 : 1995 | Identical |
| NBN EN 10016-1 : 1995 | Identical |
| BS EN 10016-1:1995 | Identical |
| UNE-EN 10016-1:1995 | Identical |
| NF EN 10016-1 : 1995 | Identical |
| SN EN 10016-1 : 1995 | Identical |
| I.S. EN 10016-1:1995 | Identical |
| PN EN 10016-1 : 1999 | Identical |
| 08/30189622 DC : 0 | BS EN 10223-8 - STEEL WIRE AND WIRE PRODUCTS FOR FENCES - PART 8: WELDED MESH GABION PRODUCTS |
| 08/30180859 DC : DRAFT JUNE 2008 | BS EN 10218-1 - STEEL WIRE AND WIRE PRODUCTS - GENERAL - PART 1: TEST METHODS |
| 08/30189604 DC : 0 | BS EN 10223-2 - STEEL WIRE AND WIRE PRODUCTS FOR FENCES - PART 2: HEXAGONAL STEEL WIRE NETTING FOR AGRICULTURAL, INSULATION, AND FENCING PURPOSES |
| BS EN 10016-3:1995 | Non-alloy steel rods for drawing and/or cold rolling Specific requirements for rimmed and rimmed substitute low carbon steel rod |
| BS EN 10230-1:2000 | Steel wire nails Loose nails for general applications |
| BS EN 10016-2:1995 | Non-alloy steel rods for drawing and/or cold rolling Specific requirements for general purpose rod |
| EN 10230-1:1999 | Steel wire nails - Part 1: Loose nails for general applications |
| EN 10016-3:1994 | Non-alloy steel rod for drawing and/or cold rolling - Part 3: Specific requirements for rimmed and rimmed substitute low carbon steel rod |
| EN 10016-4:1994 | Non-alloy steel rod for drawing and/or cold rolling - Part 4: Specific requirements for rod for special applications |
| I.S. EN 10016-2:1995 | NON-ALLOY STEEL ROD FOR DRAWING AND/OR COLD ROLLING - PART 2: SPECIFIC REQUIREMENTS FOR GENERAL PURPOSES ROD |
| 08/30189607 DC : 0 | BS EN 10223-3 - STEEL WIRE AND WIRE PRODUCTS FOR FENCES - PART 3: HEXAGONAL STEEL WIRE NETTING FOR ENGINEERING PURPOSES |
| PREN 10223-6 : DRAFT 2008 | STEEL WIRE AND WIRE PRODUCTS FOR FENCES - PART 6: STEEL WIRE CHAIN LINK FENCING |
| PREN 10257-1 : DRAFT 2008 | ZINC OR ZINC ALLOY COATED NON-ALLOY STEEL WIRE FOR ARMOURING EITHER POWER CABLES OR TELECOMMUNICATION CABLES - PART 1: LAND CABLES |
| PREN 10257-2 : DRAFT 2008 | ZINC OR ZINC ALLOY COATED NON-ALLOY STEEL WIRE FOR ARMOURING EITHER POWER CABLES OR TELECOMMUNICATION CABLES - PART 2: SUBMARINE CABLES |
| 08/30189601 DC : 0 | BS EN 10223-1 - STEEL WIRE AND WIRE PRODUCTS FOR FENCES - PART 1: ZINC AND ZINC-ALLOY COATED STEEL BARBED WIRE |
| I.S. EN 10016-4:1995 | NON-ALLOY STEEL ROD FOR DRAWING AND/OR COLD ROLLING - PART 4: SPECIFIC REQUIREMENTS FOR ROD FOR SPECIAL APPLICATIONS |
| 08/30180150 DC : DRAFT JUNE 2008 | BS EN 10264-2 - STEEL WIRE AND WIRE PRODUCTS - STEEL WIRE FOR ROPES - PART 2: COLD DRAWN NON-ALLOY STEEL WIRE FOR ROPES FOR GENERAL APPLICATIONS |
| UNI EN 10324 : 2005 | STEEL WIRE AND WIRE PRODUCTS - HOSE REINFORCEMENT WIRE |
| I.S. EN 10016-3:1995 | NON-ALLOY STEEL ROD FOR DRAWING AND/OR COLD ROLLING - PART 3: SPECIFIC REQUIREMENTS FOR RIMMED AND RIMMED SUBSTITUTE LOW CARBON STEEL ROD |
| 08/30180153 DC : DRAFT JUNE 2008 | BS EN 10264-3 - STEEL WIRE AND WIRE PRODUCTS - STEEL WIRE FOR ROPES - PART 3: ROUND AND SHAPED NON ALLOYED STEEL WIRE FOR HIGH DUTY APPLICATIONS |
| PREN 10223-3 : DRAFT 2008 | STEEL WIRE AND WIRE PRODUCTS FOR FENCES - PART 3: HEXAGONAL STEEL WIRE MESH PRODUCTS FOR ENGINEERING PURPOSES |
| PREN 10223-1 : DRAFT 2008 | STEEL WIRE AND WIRE PRODUCTS FOR FENCES - PART 1: ZINC AND ZINC-ALLOY COATED STEEL BARBED WIRE |
| 08/30189616 DC : 0 | BS EN 10223-6 - STEEL WIRE AND WIRE PRODUCTS FOR FENCES - PART 6: STEEL WIRE CHAIN LINK FENCING |
| 08/30180850 DC : DRAFT JUNE 2008 | BS EN 10270-1 - STEEL WIRE FOR MECHANICAL SPRINGS - PART 1: PATENTED COLD DRAWN UNALLOYED SPRING STEEL WIRE |
| DIN EN 10324:2004-11 | STEEL WIRE AND WIRE PRODUCTS - HOSE REINFORCEMENT WIRE |
| BS EN 10324:2004 | Steel wire and wire products. Hose reinforcement wire |
| BS EN 10016-4:1995 | Non-alloy steel rods for drawing and/or cold rolling Specific requirements for rod for special applications |
| 08/30189625 DC : 0 | BS EN 10257-1 - ZINC OR ZINC ALLOY COATED NON-ALLOY STEEL WIRE FOR ARMOURING EITHER POWER CABLES OR TELECOMMUNICATION CABLES - PART 1: LAND CABLES |
| 08/30189628 DC : 0 | BS EN 10257-2 - ZINC OR ZINC ALLOY COATED NON-ALLOY STEEL WIRE FOR ARMOURING EITHER POWER CABLES OR TELECOMMUNICATION CABLES - PART 2: SUBMARINE CABLES |
| PREN 10223-2 : DRAFT 2008 | STEEL WIRE AND WIRE PRODUCTS FOR FENCES - PART 2: HEXAGONAL STEEL WIRE NETTING FOR AGRICULTURAL, INSULATION AND FENCING PURPOSES |
| BS EN 10323:2004 | Steel wire and products. Bead wire |
| DIN EN 10323:2004-11 | Steel wire and wire products - Bead wire; German version EN 10323:2004 |
| EN 10016-2:1994 | Non-alloy steel rod for drawing and/or cold rolling - Part 2: Specific requirements for general purposes rod |
| EN 10324:2004/AC:2008 | STEEL WIRE AND WIRE PRODUCTS - HOSE REINFORCEMENT WIRE |
| EN 10323:2004 | Steel wire and wire products - Bead wire |
| EN 10002-1 : 2001 | METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT AMBIENT TEMPERATURE |
| EN 10052:1993 | Vocabulary of heat treatment terms for ferrous products |
| EN 10079:2007 | Definition of steel products |
| EN 10027-2:2015 | DESIGNATION SYSTEMS FOR STEELS - PART 2: NUMERICAL SYSTEM |
| EURONORM 18 : 1979 | TAKING AND PREPARATION OF SAMPLES AND SAMPLE SECTIONS OF STEEL AND STEEL PRODUCTS |
| NBN ECISS IC 10 : 1993 | DESIGNATION SYSTEM FOR STEEL - ADDITIONAL SYMBOLS FOR STEEL NAMES |
| EURONORM 104 : 1970 | DETERMINATION OF THE DECARBURIZATION DEPTH OF UNALLOYED AND LOW-ALLOY STRUCTURAL STEELS |
| EN 10021:2006 | General technical delivery conditions for steel products |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| EN 10027-1:2016 | Designation systems for steels - Part 1: Steel names |
| EN 10020:2000 | Definition and classification of grades of steel |
| EURONORM 17 : 1970 | WIRE ROD OF COMMON UNALLOYED STEELS FOR DRAWING; DIMENSIONS AND PERMISSIBLE DEVIATIONS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.