EN 10028-5:2017
Current
Current
The latest, up-to-date edition.
Flat products made of steels for pressure purposes - Part 5: Weldable fine grain steels, thermomechanically rolled
Published date
07-26-2017
Publisher
European foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Tolerances on dimensions
5 Calculation of mass
6 Classification and designation
7 Information to be supplied by the purchaser
8 Requirements
9 Inspection
10 Sampling
11 Test methods
12 Marking
Annex A (informative) - Information on weldability
Annex B (informative) - Changes to the previous version
EN 10028-5:2009
Annex ZA (informative) - Relationship between this
European Standard and the Essential Requirements
of Directive 2014/68/EU
This European Standard specifies the requirements for flat products for pressure equipment made of thermomechanically rolled steels as specified in Table 1.The steels are not suitable for hot forming.NOTE 1At the time of publication of this European Standard, no sufficient data for the standardization of the elevated temperature properties of these steels was available.If their use at such temperatures is intended the conditions for this should be specially agreed between the interested parties.The requirements of EN 10028 1:2017 also apply.NOTE 2Once this European Standard is published in the EU Official Journal (OJEU) under Directive 2014/68/EU, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 2014/68/EU is limited to technical data of materials in this European Standard (Part 1 and the other relevant part of the series) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 2014/68/EU are satisfied, needs to be done.
| DevelopmentNote |
Supersedes EURONORM 28. (07/2004) Supersedes PREN 10028-5. (08/2017)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| NEN EN 10028-5 : 2017 | Identical |
| PN EN 10028-5 : 2017 | Identical |
| NF EN 10028-5 : 2017 | Identical |
| BS EN 10028-5:2017 | Identical |
| DIN EN 10028-5:2017-10 | Identical |
| UNI EN 10028-5 : 2009 | Identical |
| NS EN 10028-5 : 2017 | Identical |
| UNE-EN 10028-5:2010 | Identical |
| I.S. EN 10028-5:2017 | Identical |
| SANS 50028-5 : 1ED 2009 | Identical |
| SN EN 10028-5 : 2009 | Identical |
| NBN EN 10028-5 : 2009 | Identical |
| UNE-EN 10028-5:2017 | Identical |
| UNI EN 10028-5:2017 | Identical |
| 09/30156692 DC : 0 | BS EN 10029 - HOT-ROLLED STEEL PLATES 3 MM THICK OR ABOVE - TOLERANCES ON DIMENSIONS AND SHAPE |
| PREN 10051 : DRAFT 2009 | HOT-ROLLED STRIP AND PLATE/SHEET CUT FROM WIDE STRIP OF NON-ALLOY AND ALLOY STEELS - TOLERANCES ON DIMENSIONS AND SHAPE |
| I.S. EN 14638-3:2010 | TRANSPORTABLE GAS CYLINDERS - REFILLABLE WELDED RECEPTACLES OF A CAPACITY NOT EXCEEDING 150 LITRES - PART 3: WELDED CARBON STEEL CYLINDERS MADE TO A DESIGN JUSTIFIED BY EXPERIMENTAL METHODS |
| I.S. EN 13322-1:2003 | TRANSPORTABLE GAS CYLINDERS - REFILLABLE WELDED STEEL GAS CYLINDERS - DESIGN AND CONSTRUCTION - PART 1: CARBON STEEL |
| NF EN 12542 : 2011 | LPG EQUIPMENT AND ACCESSORIES - STATIC WELDED STEEL CYLINDRICAL TANKS, SERIALLY PRODUCED FOR THE STORAGE OF LIQUEFIED PETROLEUM GAS (LPG) HAVING A VOLUME NOT GREATER THAN 13 M[3] - DESIGN AND MANUFACTURE |
| BS EN 13480-2:2017 | Metallic industrial piping Materials |
| BS EN 14208:2004 | Transportable gas cylinders. Specification for welded pressure drums up to 1000 litre capacity for the transport of gases. Design and construction |
| DIN EN 14893:2014-09 | LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE LIQUEFIED PETROLEUM GAS (LPG) WELDED STEEL PRESSURE DRUMS WITH A CAPACITY BETWEEN 150 LITRES AND 1000 LITRES |
| BS EN 10029:2010 | Hot-rolled steel plates 3 mm thick or above. Tolerances on dimensions and shape |
| BS EN 14075:2002 | Static welded steel cylindrical tanks, serially produced for the storage of liquefied petroleum gas (LPG) having a volume not greater than 13 m<sup>3</sup> and for installation underground. Design and manufacture |
| EN 10028-1:2017 | Flat products made of steels for pressure purposes - Part 1: General requirements |
| 13/30248693 DC : 0 | BS EN 14893 - LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE LIQUEFIED PETROLEUM GAS (LPG) WELDED STEEL PRESSURE DRUMS WITH A CAPACITY BETWEEN 150 LITRES AND 1000 LITRES |
| I.S. EN 13611:2015 | SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS |
| 04/30116684 DC : DRAFT JUL 2004 | EN 14893 - LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE LPG METALLIC PRESSURE DRUMS WITH A CAPACITY BETWEEN (150 AND 1 000 LITRES) |
| PREN 10164 : DRAFT 2016 | STEEL PRODUCTS WITH IMPROVED DEFORMATION PROPERTIES PERPENDICULAR TO THE SURFACE OF THE PRODUCT - TECHNICAL DELIVERY CONDITIONS |
| 09/30200092 DC : 0 | BS EN 10051 - HOT-ROLLED STRIP AND PLATE/SHEET CUT FROM WIDE STRIP OF NON-ALLOY AND ALLOY STEELS - TOLERANCES ON DIMENSIONS AND SHAPE |
| PREN 10029 : DRAFT 2009 | HOT-ROLLED STEEL PLATES 3 MM THICK OR ABOVE - TOLERANCES ON DIMENSIONS AND SHAPE |
| DIN EN 14893 E : 2014 | LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE LIQUEFIED PETROLEUM GAS (LPG) WELDED STEEL PRESSURE DRUMS WITH A CAPACITY BETWEEN 150 LITRES AND 1000 LITRES |
| S.R. CEN ISO TR 20172:2009 | WELDING - GROUPING SYSTEMS FOR MATERIALS - EUROPEAN MATERIALS |
| BS EN 13445-2 : 2014 | UNFIRED PRESSURE VESSELS - PART 2: MATERIALS |
| 17/30360051 DC : 0 | BS EN 13611 - SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS |
| UNE-EN 12542:2011 | LPG equipment and accessories - Static welded steel cylindrical tanks, serially produced for the storage of Liquefied Petroleum Gas (LPG) having a volume not greater than 13 m³ - Design and manufacture |
| I.S. EN 12542:2010 | LPG EQUIPMENT AND ACCESSORIES - STATIC WELDED STEEL CYLINDRICAL TANKS, SERIALLY PRODUCED FOR THE STORAGE OF LIQUEFIED PETROLEUM GAS (LPG) HAVING A VOLUME NOT GREATER THAN 13 M[3] - DESIGN AND MANUFACTURE |
| I.S. EN 10029:2010 | HOT-ROLLED STEEL PLATES 3 MM THICK OR ABOVE - TOLERANCES ON DIMENSIONS AND SHAPE |
| DIN EN 12542:2010-12 | LPG EQUIPMENT AND ACCESSORIES - STATIC WELDED STEEL CYLINDRICAL TANKS, SERIALLY PRODUCED FOR THE STORAGE OF LIQUEFIED PETROLEUM GAS (LPG) HAVING A VOLUME NOT GREATER THAN 13 M[3] - DESIGN AND MANUFACTURE |
| DIN EN 10028-1:2017-10 | FLAT PRODUCTS MADE OF STEELS FOR PRESSURE PURPOSES - PART 1: GENERAL REQUIREMENTS |
| DIN EN 13611:2019-06 | Safety and control devices for burners and appliances burning gaseous and/or liquid fuels - General requirements |
| I.S. EN 14893:2014 | LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE LIQUEFIED PETROLEUM GAS (LPG) WELDED STEEL PRESSURE DRUMS WITH A CAPACITY BETWEEN 150 LITRES AND 1000 LITRES |
| I.S. EN 10028-1:2017 | FLAT PRODUCTS MADE OF STEELS FOR PRESSURE PURPOSES - PART 1: GENERAL REQUIREMENTS |
| UNI EN 10029 : 2011 | Hot rolled steel sheets with a thickness greater than or equal to 3 mm - Tolerances on dimensions and shape |
| 08/30180502 DC : DRAFT JUNE 2008 | BS EN 12542 - LPG EQUIPMENT AND ACCESSORIES - STATIC WELDED STEEL CYLINDRICAL TANKS, SERIALLY PRODUCED FOR THE STORAGE OF LIQUEFIED PETROLEUM GAS (LPG) HAVING A VOLUME NOT GREATER THAN 13 M[3] - DESIGN AND MANUFACTURE |
| BS EN 14638-3:2010 | Transportable gas cylinders. Refillable welded receptacles of a capacity not exceeding 150 litres Welded carbon steel cylinders made to a design justified by experimental methods |
| CEN ISO/TR 20172:2009 | Welding - Grouping systems for materials - European materials (ISO/TR 20172:2009) |
| 16/30338590 DC : 0 | BS EN 10164 - STEEL PRODUCTS WITH IMPROVED DEFORMATION PROPERTIES PERPENDICULAR TO THE SURFACE OF THE PRODUCT - TECHNICAL DELIVERY CONDITIONS |
| 17/30347443 DC : DRAFT JUN 2017 | BS EN 12480 - GAS METERS - ROTARY DISPLACEMENT GAS METERS |
| 08/30167676 DC : DRAFT JAN 2008 | BS EN 10120 - STEEL SHEET AND STRIP FOR WELDED GAS CYLINDERS |
| ONORM EN 13322-1 : 2006 | TRANSPORTABLE GAS CYLINDERS - REFILLABLE WELDED STEEL GAS CYLINDERS - DESIGN AND CONSTRUCTION - PART 1: CARBON STEEL |
| UNE-EN 10029:2011 | Hot-rolled steel plates 3 mm thick or above - Tolerances on dimensions and shape |
| EN 13445-2:2014/A2:2018 | UNFIRED PRESSURE VESSELS - PART 2: MATERIALS |
| PREN 12542 : DRAFT 2016 | LPG EQUIPMENT AND ACCESSORIES - STATIC WELDED STEEL CYLINDRICAL TANKS, SERIALLY PRODUCED FOR THE STORAGE OF LIQUEFIED PETROLEUM GAS (LPG) HAVING A VOLUME NOT GREATER THAN 13 M[3] - DESIGN AND MANUFACTURE |
| BS EN 13322-1 : 2003 | TRANSPORTABLE GAS CYLINDERS - REFILLABLE WELDED STEEL GAS CYLINDERS - DESIGN AND CONSTRUCTION - PART 1: CARBON STEEL |
| UNI EN 12542 : 2010 | LPG EQUIPMENT AND ACCESSORIES - STATIC WELDED STEEL CYLINDRICAL TANKS, SERIALLY PRODUCED FOR THE STORAGE OF LIQUEFIED PETROLEUM GAS (LPG) HAVING A VOLUME NOT GREATER THAN 13 MUE - DESIGN AND MANUFACTURE |
| EN 12542:2010 | LPG equipment and accessories - Static welded steel cylindrical tanks, serially produced for the storage of Liquefied Petroleum Gas (LPG) having a volume not greater than 13 m³ - Design and manufacture |
| EN 14208:2004 | Transportable gas cylinders - Specification for welded pressure drums up to 1000 litre capacity for the transport of gases - Design and construction |
| UNI EN 14893 : 2014 | LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE LIQUEFIED PETROLEUM GAS (LPG) WELDED STEEL PRESSURE DRUMS WITH A CAPACITY BETWEEN 150 LITRES AND 1000 LITRES |
| UNI EN 1106 : 2010 | MANUALLY OPERATED TAPS FOR GAS BURNING APPLIANCES |
| UNI EN 10051 : 2011 | CONTINUOUSLY HOT-ROLLED STRIP AND PLATE/SHEET CUT FROM WIDE STRIP OF NON-ALLOY AND ALLOY STEELS - TOLERANCES ON DIMENSIONS AND SHAPE |
| UNI EN 1854 : 2010 | PRESSURE SENSING DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES |
| 99/707159 DC : DRAFT APR 99 | BS PREN 13480-2 - METALLIC INDUSTRIAL PIPING - PART 2: MATERIALS |
| 12/30257022 DC : 0 | BS EN 13611 - SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS - GENERAL REQUIREMENTS |
| I.S. EN 13445-2:2014 | UNFIRED PRESSURE VESSELS - PART 2: MATERIALS |
| DIN EN 14638-3:2012-06 | Transportable gas cylinders - Refillable welded receptacles of a capacity not exceeding 150 litres - Part 3: Welded carbon steel cylinders made to a design justified by experimental methods (includes Corrigendum AC:2012) |
| UNI EN 14638-3 : 2010 | TRANSPORTABLE GAS CYLINDERS - REFILLABLE WELDED RECEPTACLES OF A CAPACITY NOT EXCEEDING 150 LITRES - PART 3: WELDED CARBON STEEL CYLINDERS MADE TO A DESIGN JUSTIFIED BY EXPERIMENTAL METHODS |
| UNE-EN 13611:2016 | Safety and control devices for burners and appliances burning gaseous and/or liquid fuels - General requirements |
| 16/30326248 DC : 0 | BS EN 12542 - LPG EQUIPMENT AND ACCESSORIES - STATIC WELDED STEEL CYLINDRICAL TANKS, SERIALLY PRODUCED FOR THE STORAGE OF LIQUEFIED PETROLEUM GAS (LPG) HAVING A VOLUME NOT GREATER THAN 13 M[3] - DESIGN AND MANUFACTURE |
| DIN EN 13611:2016-09 | SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS |
| PREN 13611 : DRAFT 2017 | SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS |
| PREN 14893 : DRAFT 2013 | LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE LIQUEFIED PETROLEUM GAS (LPG) WELDED STEEL PRESSURE DRUMS WITH A CAPACITY BETWEEN 150 LITRES AND 1000 LITRES |
| DIN EN 13322-1:2006-05 | TRANSPORTABLE GAS CYLINDERS - REFILLABLE WELDED STEEL GAS CYLINDERS - DESIGN AND CONSTRUCTION - PART 1: CARBON STEEL |
| EN 12480:2018 | Gas meters - Rotary displacement gas meters |
| I.S. EN 12480:2018 | GAS METERS - ROTARY DISPLACEMENT GAS METERS |
| BS EN 13480-2:2017+A3:2018 | Metallic industrial piping Materials |
| DIN EN 10029:2011-02 | Hot-rolled steel plates 3 mm thick or above - Tolerances on dimensions and shape |
| DIN EN 14208:2004-05 | Transportable gas cylinders - Specification for welded pressure drums up to 1000 litre capacity for the transport of gases - Design and construction |
| BS EN 12542:2010 | LPG equipment and accessories. Static welded steel cylindrical tanks, serially produced for the storage of liquefied petroleum gas (LPG) having a volume not greater than 13 m<sup>3</sup>. Design and manufacture |
| EN 13480-2:2017 | Metallic industrial piping - Part 2: Materials |
| UNE-EN 10028-1:2017 | Flat products made of steels for pressure purposes - Part 1: General requirements |
| EN 14893:2014 | LPG equipment and accessories - Transportable Liquefied Petroleum Gas (LPG) welded steel pressure drums with a capacity between 150 litres and 1 000 litres |
| EN 14638-3:2010/AC:2012 | TRANSPORTABLE GAS CYLINDERS - REFILLABLE WELDED RECEPTACLES OF A CAPACITY NOT EXCEEDING 150 LITRES - PART 3: WELDED CARBON STEEL CYLINDERS MADE TO A DESIGN JUSTIFIED BY EXPERIMENTAL METHODS |
| EN 14075:2002/A1:2004 | STATIC WELDED STEEL CYLINDRICAL TANKS, SERIALLY PRODUCED FOR THE STORAGE OF LIQUEFIED PETROLEUM GAS (LPG) HAVING A VOLUME NOT GREATER THAN 13 M[3] AND FOR INSTALLATION UNDERGROUND - DESIGN AND MANUFACTURE |
| UNE-EN 14893:2014 | LPG equipment and accessories - Transportable Liquefied Petroleum Gas (LPG) welded steel pressure drums with a capacity between 150 litres and 1 000 litres |
| I.S. EN 14075:2002 | STATIC WELDED STEEL CYLINDRICAL TANKS, SERIALLY PRODUCED FOR THE STORAGE OF LIQUEFIED PETROLEUM GAS (LPG) HAVING A VOLUME NOT GREATER THAN 13 M[3] AND FOR INSTALLATION UNDERGROUND - DESIGN AND MANUFACTURE |
| PD CR 10313:2000 | Classification of grades of steel. Examples of classification related to European standards |
| S.R. CEN ISO/TR 20172:2021 | Welding - Grouping systems for materials - European materials (ISO/TR 20172:2021) |
| PD CEN ISO/TR 20172:2009 | Welding. Grouping systems for materials. European materials |
| NF EN 14638-3 : 2010 | TRANSPORTABLE GAS CYLINDERS - REFILLABLE WELDED RECEPTACLES OF A CAPACITY NOT EXCEEDING 150 LITRES - PART 3: WELDED CARBON STEEL, CYLINDERS MADE TO A DESIGN JUSTIFIED BY EXPERIMENTAL METHODS |
| UNE-EN 14638-3:2011 | Transportable gas cylinders - Refillable welded receptacles of a capacity not exceeding 150 litres - Part 3: Welded carbon steel cylinders made to a design justified by experimental methods |
| I.S. CEN ISO TR 20172:2006 | WELDING - GROUPING SYSTEMS FOR MATERIALS - EUROPEAN MATERIALS |
| UNE-EN 13445-2:2015 | Unfired pressure vessels - Part 2: Materials |
| BS EN 13611:2015 | Safety and control devices for burners and appliances burning gaseous and/or liquid fuels. General requirements |
| EN 13611:2015/AC:2016 | SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS |
| EN 13322-1:2003/A1:2006 | TRANSPORTABLE GAS CYLINDERS - REFILLABLE WELDED STEEL GAS CYLINDERS - DESIGN AND CONSTRUCTION - PART 1: CARBON STEEL |
| S.R. CR 10313:2000 | CLASSIFICATION OF GRADES OF STEEL - EXAMPLES OF CLASSIFICATION RELATED TO EUROPEAN STANDARDS |
| BS EN 14893:2014 | LPG equipment and accessories. Transportable Liquefied Petroleum Gas (LPG) welded steel pressure drums with a capacity between 150 litres and 1 000 litres |
| BS EN 10028-1:2017 | Flat products made of steels for pressure purposes General requirements |
| ISO/TR 20172:2009 | Welding Grouping systems for materials European materials |
| I.S. EN 13611:2015/AC:2016 | SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS |
| CR 10313:2000 | Classification of grades of steel - Examples of classification related to European Standards |
| EN 10029:2010 | Hot-rolled steel plates 3 mm thick or above - Tolerances on dimensions and shape |
| DIN EN 14075:2003-01 | STATIC WELDED STEEL CYLINDRICAL TANKS, SERIALLY PRODUCED FOR THE STORAGE OF LIQUEFIED PETROLEUM GAS (LPG) HAVING A VOLUME NOT GREATER THAN 13 M[3] AND FOR INSTALLATION UNDERGROUND - DESIGN AND MANUFACTURE |
| UNE-EN 13480-2:2017 | Metallic industrial piping - Part 2: Materials (Endorsed by Asociación Española de Normalización in September of 2019.) |
| EN 10028-1:2017 | Flat products made of steels for pressure purposes - Part 1: General requirements |
| EN 1011-1:2009 | Welding - Recommendations for welding of metallic materials - Part 1: General guidance for arc welding |
| EN 1011-2:2001/A1:2003 | WELDING - RECOMMENDATIONS FOR WELDING OF METALLIC MATERIALS - PART 2: ARC WELDING OF FERRITIC STEELS |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| EN 10020:2000 | Definition and classification of grades of steel |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.