• There are no items in your cart

EN 12115:2011

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Rubber and thermoplastics hoses and hose assemblies for liquid or gaseous chemicals - Specification
Superseded date

01-28-2021

Published date

01-19-2011

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Couplings and end fittings
6 Materials and construction
7 Dimensions and tolerances, typical masses
8 Physical properties of materials used for hoses
9 Performance requirements of hoses and hose assemblies
10 Electrical properties
11 Frequency of testing
12 Type tests
13 Test report
14 Marking
15 Storage and admissible storage time
Annex A (normative) - Test frequency for type tests and
        routine tests
Annex B (informative) - Production acceptance tests
Annex C (informative) - Couplings and fittings
Annex D (normative) - Crush recovery test (for SD hoses only)
Annex E (normative) - Flammability test
Annex F (informative) - Resistance to chemicals conveyed
Bibliography

This European Standard specifies requirements for two types of hose assemblies (Types D and SD) and four grades based on electrical properties with hoses made of rubber or thermoplastics and hose fittings made of metal designed to convey liquid or gaseous chemical substances, hereinafter termed the "chemicals conveyed".The hose assemblies are intended for use with chemicals conveyed in the temperature range of 20 °C to +65 °C at a working pressure  10 bar ).NOTE 1This European Standard sets out requirements for these hose assemblies to ensure that users are not exposed to danger from fire or explosion and that the environment is protected against contamination or damage.NOTE 2Other temperatures and working pressures than those given above can be agreed with the manufacturer, provided that the marking on the hose (see 14.1) states this and the requirements of Table 5 and all the other requirements are met.NOTE 3Other diameters than those given in this European Standard can be agreed with the manufacturer.NOTE 4This European Standard also provides guidance on the storage of hose assemblies (Clause 15).NOTE 5The attention of users is drawn to Annex F concerning the selection of lining material related to the chemical(s) to be conveyed by the hoses and/or hose assemblies.This standard does not apply to hose assemblies for:-aircraft refuelling (EN 1361);-fuel dispensing (EN 1360);-oil burners (EN ISO 6806);-refrigerant circuits;-fuel truck delivery (EN 1761);-liquid petroleum gases (LPG) (EN 1762);-fire fighting (EN ISO 14557);-oil suction and discharge (EN 1765);-rotary drilling (EN ISO 6807);-fuel dispensing with vapour recovery system (EN 13483).This European Standard does not apply to multilayer hose assemblies (EN 13765 and EN 13766).

Committee
CEN/TC 218
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

Standards Relationship
UNE-EN 12115:2000 Identical
BS EN 12115:2011 Identical
DIN EN 12115:2011-04 Identical
PN EN 12115 : 2011 Identical
NEN EN 12115 : 2011 Identical
NF EN 12115 : 2011 Identical
SN EN 12115 : 2011 Identical
SS-EN 12115:2011 Identical
UNE-EN 12115:2011 Identical
NBN EN 12115 : 2011 Identical
NS EN 12115 : 2011 Identical
UNI EN 12115 : 2011 Identical
I.S. EN 12115:2011 Identical
ONORM EN 12115 : OCT 2011 Identical

DIN EN 16820 E : 2017 RUBBER AND PLASTICS HOSES AND HOSE ASSEMBLIES FOR USE IN THE PHARMACEUTICAL AND BIOTECHNOLOGICAL INDUSTRY - BONDED ELASTOMERIC HOSES WITH OR WITHOUT A LINING
EN 12798:2007 (edition 2) Transport Quality Management System - Road, Rail and Inland navigation transport - Quality management system requirements to supplement EN ISO 9001 for the transport of dangerous goods with regard to safety
I.S. EN 12798:2007 TRANSPORT QUALITY MANAGEMENT SYSTEM - ROAD, RAIL AND INLAND NAVIGATION TRANSPORT - QUALITY MANAGEMENT SYSTEM REQUIREMENTS TO SUPPLEMENT EN ISO 9001 FOR THE TRANSPORT OF DANGEROUS GOODS WITH REGARD TO SAFETY
DIN EN 14420-1:2013-09 Hose fittings with clamp units - Part 1: Requirements, types of fixing and connection, designation and testing
I.S. EN 14420-1:2013 HOSE FITTINGS WITH CLAMP UNITS - PART 1: REQUIREMENTS, TYPES OF FIXING AND CONNECTION, DESIGNATION AND TESTING
15/30315105 DC : 0 BS EN 16820 - HOSE ASSEMBLIES FOR USE IN THE PHARMACEUTICAL AND BIOTECHNOLOGICAL INDUSTRY WITH HOSES OF NON-METALLIC MATERIALS - ELASTOMERIC HOSES WITH OR WITHOUT LINER
DIN EN 16820:2015-03 (Draft) RUBBER AND PLASTICS HOSES AND HOSE ASSEMBLIES FOR USE IN THE PHARMACEUTICAL AND BIOTECHNOLOGICAL INDUSTRY - BONDED ELASTOMERIC HOSES WITH OR WITHOUT A LINING
UNI EN 14420-1 : 2013 HOSE FITTINGS WITH CLAMP UNITS - PART 1: REQUIREMENTS, TYPES OF FIXING AND CONNECTION, DESIGNATION AND TESTING
BS EN 16820:2017 Rubber and plastics hoses and hose assemblies for use in the pharmaceutical and biotechnological industry. Bonded elastomeric hoses with or without a lining
10/30234625 DC : 0 BS EN 14420-1 - HOSE FITTINGS WITH CLAMP UNITS - PART 1: REQUIREMENTS, SURVEY, DESIGNATION AND TESTING
DIN EN 12798:2007-08 Transport quality management system - Road, rail and inland navigation transport - Quality management system requirements to supplement EN ISO 9001 for the transport of dangerous goods with regard to safety
BS EN 14420-1:2013 Hose fittings with clamp units Requirements, types of fixing and connection, designation and testing
EN 14420-1:2013 Hose fittings with clamp units - Part 1: Requirements, types of fixing and connection, designation and testing
EN 16820:2017 Rubber and plastics hoses and hose assemblies for use in the pharmaceutical and biotechnological industry - Bonded elastomeric hoses with or without a lining
EI 1540 : 2014 DESIGN, CONSTRUCTION, COMMISSIONING, MAINTENANCE AND TESTING OF AVIATION FUELLING FACILITIES
PREN 14420-1 : DRAFT 2010 HOSE FITTINGS WITH CLAMP UNITS - PART 1: REQUIREMENTS, SURVEY, DESIGNATION AND TESTING
I.S. EN 16820:2017 RUBBER AND PLASTICS HOSES AND HOSE ASSEMBLIES FOR USE IN THE PHARMACEUTICAL AND BIOTECHNOLOGICAL INDUSTRY - BONDED ELASTOMERIC HOSES WITH OR WITHOUT A LINING
UNE-EN 16820:2018 Rubber and plastics hoses and hose assemblies for use in the pharmaceutical and biotechnological industry - Bonded elastomeric hoses with or without a lining
BS EN 12798:2007 Transport quality management system. Road rail and inland navigation transport. Quality management system requirements to supplement EN ISO 9001 for the transport of dangerous goods, with regard to safety

EN ISO 8330:2014 Rubber and plastics hoses and hose assemblies - Vocabulary (ISO 8330:2014)
EN 13766:2010 Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of liquid petroleum gas and liquefied natural gas - Specification
EN ISO 14557:2002/A1:2007 FIRE-FIGHTING HOSES - RUBBER AND PLASTICS SUCTION HOSES AND HOSE ASSEMBLIES
EN ISO 7233:2016 Rubber and plastics hoses and hose assemblies - Determination of resistance to vacuum (ISO 7233:2016)
EN ISO 1402:2009 Rubber and plastics hoses and hose assemblies - Hydrostatic testing (ISO 1402:2009)
EN ISO 4671:2007/A1:2011 Rubber and plastics hoses and hose assemblies - Methods of measurement of the dimensions of hoses and the lengths of hose assemblies - Amendment 1: Clarification of position at which outside diameter is measured (ISO 4671:2007/Amd 1:2011)
EN 60079-10-1:2015 Explosive atmospheres - Part 10-1: Classification of areas - Explosive gas atmospheres
EN 10244-2:2009 Steel wire and wire products - Non-ferrous metallic coatings on steel wire - Part 2: Zinc or zinc alloy coatings
EN 14420-7:2013 Hose fittings with clamp units - Part 7: Cam locking couplings
EN 13483:2013 Rubber and plastic hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems - Specification
ISO 4649:2017 Rubber, vulcanized or thermoplastic — Determination of abrasion resistance using a rotating cylindrical drum device
ISO 4672:1997 Rubber and plastics hoses Sub-ambient temperature flexibility tests
EN 10088-3:2014 Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes
EN 14420-1:2013 Hose fittings with clamp units - Part 1: Requirements, types of fixing and connection, designation and testing
ISO 188:2011 Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
EN ISO 8031:2009 Rubber and plastics hoses and hose assemblies - Determination of electrical resistance and conductivity (ISO 8031:2009)
EN ISO 4672 : 1999 RUBBER AND PLASTICS HOSES - SUB-AMBIENT TEMPERATURE FLEXIBILITY TESTS
EN 1361 : 2004 RUBBER HOSES AND HOSE ASSEMBLIES FOR AVIATION FUEL HANDLING - SPECIFICATION
EN 60079-10-2:2015 Explosive atmospheres - Part 10-2: Classification of areas - Explosive dust atmospheres
ISO 7233:2016 Rubber and plastics hoses and hose assemblies Determination of resistance to vacuum
IEC 60079-10-1:2015 Explosive atmospheres - Part 10-1: Classification of areas - Explosive gas atmospheres
EN 14420-4:2013 Hose fittings with clamp units - Part 4: Flange connections
ISO 8331:2016 Rubber and plastics hoses and hose assemblies Guidelines for selection, storage, use and maintenance
EN 14420-5:2013 Hose fittings with clamp units - Part 5: Threaded connections
EN ISO 7326:2016 Rubber and plastics hoses - Assessment of ozone resistance under static conditions (ISO 7326:2016)
ISO 7326:2016 Rubber and plastics hoses Assessment of ozone resistance under static conditions
EN ISO 8033:2017 Rubber and plastics hoses - Determination of adhesion between components (ISO 8033:2016)
EN 14420-2:2013 Hose fittings with clamp units - Part 2: Hose side parts of hose tail
ISO 8330:2007 Rubber and plastics hoses and hose assemblies Vocabulary
EN 13765:2010+A1:2015 Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of hydrocarbons, solvents and chemicals - Specification
EN 10270-1:2011+A1:2017 Steel wire for mechanical springs - Part 1: Patented cold drawn unalloyed spring steel wire
EN 14420-8:2013+A1:2016 Hose fittings with clamp units - Part 8: Symmetrical half coupling (Guillemin system)
EN 14540:2014 Fire-fighting hoses - Non-percolating layflat hoses for fixed systems
EN ISO 6806:2017 Rubber hoses and hose assemblies for use in oil burners - Specification (ISO 6806:2017)
EN 694:2014 Fire-fighting hoses - Semi-rigid hoses for fixed systems
EN 1765:2016 Rubber hose assemblies for oil suction and discharge services - Specification for the assemblies
ISO/TR 17784:2003 Rubber and plastics hoses and hose assemblies Guide for use by purchasers, assemblers, installers and operating personnel
EN 1761:1999 Rubber hoses and hose assemblies for fuel truck delivery - Specification
EN ISO 6807 : 2003 RUBBER HOSES AND HOSE ASSEMBLIES FOR ROTARY DRILLING AND VIBRATION APPLICATIONS - SPECIFICATION
EN 14420-3:2013 Hose fittings with clamp units - Part 3: Clamp units, bolted or pinned
ISO 6806:2017 Rubber hoses and hose assemblies for use in oil burners — Specification
EN 14420-6:2013 Hose fittings with clamp units - Part 6: TW tank truck couplings
ISO 37:2017 Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
ISO 4671:2007 Rubber and plastics hoses and hose assemblies Methods of measurement of the dimensions of hoses and the lengths of hose assemblies
ISO 1402:2009 Rubber and plastics hoses and hose assemblies Hydrostatic testing
EN 1360:2013 Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems - Specification
ISO 6807:2003 Rubber hoses and hose assemblies for rotary drilling and vibration applications Specification
EN 1762:2017 Rubber hoses and hose assemblies for liquefied petroleum gas, LPG (liquid or gaseous phase), and natural gas up to 25 bar (2,5 MPa) - Specification
EN 10270-2:2011 Steel wire for mechanical springs - Part 2: Oil hardened and tempered spring steel wire
ISO 1629:2013 Rubber and latices — Nomenclature
ISO 8033:2016 Rubber and plastics hoses Determination of adhesion between components
ISO 8031:2009 Rubber and plastics hoses and hose assemblies Determination of electrical resistance and conductivity
CLC/TR 50404:2003 Electrostatics - Code of practice for the avoidance of hazards due to static electricity
ISO 1817:2015 Rubber, vulcanized or thermoplastic Determination of the effect of liquids
ISO 14557:2002 Fire-fighting hoses Rubber and plastics suction hoses and hose assemblies

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.