• There are no items in your cart

EN 12666-1:2005+A1:2011

Current
Current

The latest, up-to-date edition.

Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system
Published date

08-24-2011

Foreword
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviations
4 Material
5 General requirements
6 Geometrical characteristics
7 Mechanical characteristics
8 Physical characteristics
9 Performance requirements
10 Sealing rings
11 Marking
Annex A (informative) - General characteristics of PE
        pipes and fittings
Annex B (informative) - Product standards of components
        that can be connected to components conforming
        to this standard
Bibliography

This Part of EN 12666 specifies the requirements for pipes, fittings and the system of polyethylene (PE) piping systems intended to be used for-non pressure underground drainage and sewerage outside the building structure (application area code "U"), and-non pressure underground drainage and sewerage for both buried in the ground within the building structure (application area code "D") and outside the building structure.This is reflected in the marking of products by "U" and "UD".It also specifies the test parameters for the test methods referred to in this European Standard.This European Standard covers a range of nominal sizes, a range of pipe series/stiffness classes and gives recommendations concerning colours.NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.In conjunction with CEN/TS 12666-2 [1] it is applicable to PE pipes and fittings, their joints and to joints with components of other plastics and non plastics materials intended to be used for buried piping systems for non pressure drainage and sewerage.This European Standard is applicable to PE pipes with or without an integral socket.The fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings.This European Standard is applicable to PE pipes and fittings for the following types of joints:-elastomeric ring seal joints;-butt fused joints;-electrofusion joints;-mechanical joints.NOTE 2Requirements and limiting values for application area code "D" are given in Tables 3, 6 and Table 12.NOTE 3 Pipes, fittings and other components conforming to any of the plastics product standards listed in the bibliography may be used with pipes and fittings conforming to this European Standard, provided they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 8 and Table 12.

Committee
CEN/TC 155
DevelopmentNote
2005 Edition Re-Issued in August 2011 & incorporates AMD 1 2011. (09/2011)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current

S.R. CEN/TS 12666-2:2012 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) - PART 2: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY
DIN EN 124-6:2015-09 GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS - PART 6: GULLY TOPS AND MANHOLE TOPS MADE OF POLYPROPYLENE (PP), POLYETHYLENE (PE) OR UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U)
17/30341312 DC : 0 BS EN ISO 21225-1 - PLASTICS PIPING SYSTEMS FOR THE TRENCHLESS REPLACEMENT OF UNDERGROUND PIPELINE NETWORKS - PART 1: REPLACEMENT ON THE LINE BY PIPE BURSTING AND PIPE EXTRACTION
DD CEN/TS 12666-2:2005 Plastics piping systems for non-pressure underground drainage and sewerage. Polyethylene (PE) Guidance for the assessment of conformity
ISO 11296-2:2018 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 2: Lining with continuous pipes
PD CEN/TS 12666-2:2012 Plastics piping systems for non-pressure underground drainage and sewerage. Polyethylene (PE) Guidance for the assessment of conformity
UNE-EN 13598-2:2017 Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for manholes and inspection chambers
S.R. CEN/TR 1046:2013 THERMOPLASTICS PIPING AND DUCTING SYSTEMS - SYSTEMS OUTSIDE BUILDING STRUCTURES FOR THE CONVEYANCE OF WATER OR SEWAGE - PRACTICES FOR UNDERGROUND INSTALLATION
S.R. CEN/TS 15223:2017 PLASTICS PIPING SYSTEMS - VALIDATED DESIGN PARAMETERS OF BURIED THERMOPLASTICS PIPING SYSTEMS
I.S. EN 13598-2:2016 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR MANHOLES AND INSPECTION CHAMBERS
BS EN 13476-3 : 2007 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 3: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND PROFILED EXTERNAL SURFACE AND THE SYSTEM, TYPE B
EN 13566-2:2005 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 2: Lining with continuous pipes
EN 124-6:2015 Gully tops and manhole tops for vehicular and pedestrian areas - Part 6: Gully tops and manhole tops made of polypropylene (PP), polyethylene (PE) or unplasticized poly(vinyl chloride) (PVC-U)
CEN/TS 12666-2:2012 Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 2: Guidance for the assessment of conformity
DIN EN 13476-2:2007-08 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND EXTERNAL SURFACE AND THE SYSTEM, TYPE A
15/30327642 DC : 0 BS EN 13476-1 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: GENERAL REQUIREMENTS AND PERFORMANCE CHARACTERISTICS
17/30341315 DC : 0 BS EN ISO 21225-2 - PLASTICS PIPING SYSTEMS FOR THE TRENCHLESS REPLACEMENT OF UNDERGROUND PIPELINE NETWORKS - PART 2: REPLACEMENT OFF THE LINE BY HORIZONTAL DIRECTIONAL DRILLING AND IMPACT MOLING
14/30310792 DC : 0 BS EN 13598-2 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR MANHOLES AND INSPECTION CHAMBERS IN TRAFFIC AREAS AND DEEP UNDERGROUND INSTALLATIONS
07/30165577 DC : 0 BS EN 1852-1 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE (PP) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM
PREN 13476-2 : DRAFT 2015 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND EXTERNAL SURFACE AND THE SYSTEM, TYPE A
UNI CEN/TS 12666-2 : 2012 PLASTICS PIPING SYSTEMS FOR NON- PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) - PART 2: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY
DIN EN 13476-3:2015-11 (Draft) PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 3: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND PROFILED EXTERNAL SURFACE AND THE SYSTEM, TYPE B
15/30327636 DC : 0 BS EN 13476-3 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 3: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND PROFILED EXTERNAL SURFACE AND THE SYSTEM, TYPE B
I.S. EN 13476-3:2007 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY (VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 3: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND PROFILED EXTERNAL SURFACE AND THE SYSTEM, TYPE B
UNE-EN 124-6:2015 Gully tops and manhole tops for vehicular and pedestrian areas - Part 6: Gully tops and manhole tops made of polypropylene (PP), polyethylene (PE) or unplasticized poly(vinyl chloride) (PVC-U)
I.S. EN 124-6:2015 GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS - PART 6: GULLY TOPS AND MANHOLE TOPS MADE OF POLYPROPYLENE (PP), POLYETHYLENE (PE) OR UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U)
DIN EN 1366-3:2009-07 Fire resistance tests for service installations - Part 3: Penetration seals
DIN EN 13566-2:2006-02 PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 2: LINING WITH CONTINUOUS PIPES
NF EN 13598-1 : 2011 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR ANCILLARY FITTINGS INCLUDING SHALLOW INSPECTION CHAMBERS
BS EN 13566-2:2005 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Lining with continuous pipes
BS EN 13598-1:2010 Plastics piping systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Specifications for ancillary fittings including shallow inspection chambers
I.S. EN 1366-3:2009 FIRE RESISTANCE TESTS FOR SERVICE INSTALLATIONS - PART 3: PENETRATION SEALS
10/30217319 DC : 0 BS EN 13598-1 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR ANCILLARY FITTINGS INCLUDING SHALLOW INSPECTION CHAMBERS
I.S. CEN TS 12666-2:2006 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) - PART 2: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY
CEN/TR 1046:2013 Thermoplastics piping and ducting systems - Systems outside building structures for the conveyance of water or sewage - Practices for underground installation
DIN EN 124-6 E : 2015 GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS - PART 6: GULLY TOPS AND MANHOLE TOPS MADE OF POLYPROPYLENE (PP), POLYETHYLENE (PE) OR UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U)
12/30265313 DC : 0 BS EN 124-6 - GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS - PART 6: GULLY TOPS AND MANHOLE TOPS MADE FROM POLYPROPYLENE (PP) OR POLYVINYL-CHLORIDE (PVC-U)
EN 13476-3:2018 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 3: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND PROFILED EXTERNAL SURFACE AND THE SYSTEM, TYPE B
DIN EN 13476-1:2015-11 (Draft) PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: GENERAL REQUIREMENTS AND PERFORMANCE CHARACTERISTICS
BS EN 13476-2:2007 Plastics piping systems for non-pressure underground drainage and sewerage. Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Specifications for pipes and fittings with smooth internal and external surface and the system, Type A
14/30297456 DC : 0 BS EN 15013 - PLASTICS PIPING SYSTEMS - NON-PRESSURE DRAINAGE AND SEWERAGE PIPING COMPONENTS BURIED IN GROUND - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS
PREN 13476-3 : DRAFT 2015 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 3: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND PROFILED EXTERNAL SURFACE AND THE SYSTEM, TYPE B
BS EN 1401-1:2009 Plastic piping systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinyl chloride) (PVC-U) Specifications for pipes, fittings and the system
EN 13476-2:2018+A1:2020 Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for pipes and fittings with smooth internal and external surface and the system, Type A
I.S. EN 13598-1:2010 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR ANCILLARY FITTINGS INCLUDING SHALLOW INSPECTION CHAMBERS
ONORM EN 1366-3 : 2009 FIRE RESISTANCE TESTS FOR SERVICE INSTALLATIONS - PART 3: PENETRATION SEALS
UNI EN 13598-1 : 2011 PLASTICS PIPING SYSTEMS FOR NON- PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VILYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR ANCILLARY FITTINGS INCLUDING SHALLOW INSPECTION CHAMBERS
ISO 8772:2006 Plastics piping systems for non-pressure underground drainage and sewerage Polyethylene (PE)
ISO 21225-1:2018 Plastics piping systems for the trenchless replacement of underground pipeline networks — Part 1: Replacement on the line by pipe bursting and pipe extraction
06/30124428 DC : 0 EN 13598-2 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY (VINYL CHLORIDE)(PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR MANHOLES AND INSPECTION CHAMBERS IN TRAFFIC AREAS AND DEEP UNDERGROUND INSTALLATIONS
PREN 13598-2 : DRAFT 2014 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR MANHOLES AND INSPECTION CHAMBERS IN TRAFFIC AREAS AND DEEP UNDERGROUND INSTALLATIONS
I.S. EN ISO 11296-2:2018 PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 2: LINING WITH CONTINUOUS PIPES (ISO 11296-2:2018)
BS EN 13476-1:2007 Plastics piping systems for non-pressure underground drainage and sewerage. Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) General requirements and performance characteristics
PREN 13476-1 : DRAFT 2015 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYLSEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL - PART 1: GENERAL REQUIREMENTS AND PERFORMANCE CHARACTERISTICS
CEN/TS 15223:2017 Plastics piping systems - Validated design parameters of buried thermoplastics piping systems
EN 13476-1:2018 Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1:General requirements and performance characteristics
EN ISO 11296-2:2018 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 2: Lining with continuous pipes (ISO 11296-2:2018)
DIN EN 13476-2:2015-11 (Draft) PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND EXTERNAL SURFACE AND THE SYSTEM, TYPE A
EN 13598-2:2016 Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for manholes and inspection chambers
BS EN 1366-3:2009 Fire resistance tests for service installations Penetration seals
UNE-EN 1366-3:2011 Fire resistance tests for service installations - Part 3: Penetration seals
DIN EN 13598-1:2011-02 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR ANCILLARY FITTINGS INCLUDING SHALLOW INSPECTION CHAMBERS
UNE-EN 13598-1:2011 Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: Specifications for ancillary fittings including shallow inspection chambers
BS EN 12056-2:2000 Gravity drainage systems inside buildings Sanitary pipework, layout and calculation
EN 13598-1:2010 Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: Specifications for ancillary fittings including shallow inspection chambers
UNI EN 1366-3 : 2009 FIRE RESISTANCE TESTS FOR SERVICE INSTALLATIONS - PART 3: PENETRATION SEALS
EN 1401-1:2009 Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system
DIN EN 13598-2 E : 2016 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR MANHOLES AND INSPECTION CHAMBERS
DIN EN 13598-2:2016-09 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR MANHOLES AND INSPECTION CHAMBERS
BS EN 124-6:2015 Gully tops and manhole tops for vehicular and pedestrian areas Gully tops and manhole tops made of polypropylene (PP), polyethylene (PE) or unplasticized poly(vinyl chloride) (PVC-U)
I.S. EN 13476-1:2007 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY (VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: GENERAL REQUIREMENTS AND PERFORMANCE CHARACTERISTICS
15/30327639 DC : 0 BS EN 13476-2 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND EXTERNAL SURFACE AND THE SYSTEM, TYPE A
BS EN 13598-2:2009 Plastics piping systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Specifications for manholes and inspection chambers in traffic areas and deep underground installations
EN 13476-2:2018 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND EXTERNAL SURFACE AND THE SYSTEM, TYPE A
I.S. EN 13476-2:2007 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY (VINYLCHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND EXTERNAL SURFACE AND THE SYSTEM, TYPE A
DIN EN 1401-1:2009-07 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM
DIN EN 13598-1 E : 2011 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR ANCILLARY FITTINGS INCLUDING SHALLOW INSPECTION CHAMBERS
EN 1366-3:2009 Fire resistance tests for service installations - Part 3: Penetration seals

EN 295-3:2012 Vitrified clay pipe systems for drains and sewers - Part 3: Test methods
ISO 580:2005 Plastics piping and ducting systems — Injection-moulded thermoplastics fittings — Methods for visually assessing the effects of heating
EN ISO 3126:2005 Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005)
ISO/TR 10358:1993 Plastics pipes and fittings Combined chemical-resistance classification table
ISO 13259:2010 Thermoplastics piping systems for underground non-pressure applications Test method for leaktightness of elastomeric sealing ring type joints
EN 681-1:1996/A3:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
EN ISO 9967:2016 Thermoplastics pipes - Determination of creep ratio (ISO 9967:2016)
ISO 13263:2010 Thermoplastics piping systems for non-pressure underground drainage and sewerage Thermoplastics fittings Test method for impact strength
EN ISO 1043-1:2011/A1:2016 PLASTICS - SYMBOLS AND ABBREVIATED TERMS - PART 1: BASIC POLYMER AND THEIR SPECIAL CHARACTERISTICS (ISO 1043-1:2011/AMD 1:2016)
ISO 265-1:1988 Pipes and fittings of plastics materials Fittings for domestic and industrial waste pipes Basic dimensions: Metric series Part 1: Unplasticized poly(vinyl chloride) (PVC-U)
EN 1566-1:1998 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: Specifications for pipes, fittings and the system
ISO/TR 7620:2005 Rubber materials — Chemical resistance
EN ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006)
EN 681-2:2000/A2:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 2: THERMOPLASTIC ELASTOMERS
ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
ISO 11922-1:1997 Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series
EN 1455-1:1999 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 1: Requirements for pipes, fittings and the system
EN 476:2011 General requirements for components used in drains and sewers
ISO 472:2013 Plastics Vocabulary
EN 14758-1:2012 Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system
ISO 1183-1:2012 Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method
EN ISO 9969:2016 Thermoplastics pipes - Determination of ring stiffness (ISO 9969:2016)
EN ISO 580:2005 Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Methods for visually assessing the effects of heating (ISO 580:2005)
EN 1401-1:2009 Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system
EN 1519-1:1999 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system
ISO 11357-6:2008 Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT)
ISO 4065:1996 Thermoplastics pipes Universal wall thickness table
ISO 9967:2016 Thermoplastics pipes Determination of creep ratio
ISO 9624:1997 Thermoplastics pipes for fluids under pressure Mating dimensions of flange adapters and loose backing flanges
EN ISO 2505:2005 Thermoplastics pipes - Longitudinal reversion - Test method and parameters (ISO 2505:2005)
ISO 13967:2009 Thermoplastics fittings Determination of ring stiffness
EN ISO 1133:2005 PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND THE MELT VOLUME-FLOW RATE (MVR) OF THE THERMOPLASTICS
ISO 13257:2010 Thermoplastics piping systems for non-pressure applications Test method for resistance to elevated temperature cycling
CEN/TS 12666-2:2012 Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 2: Guidance for the assessment of conformity
ISO 13254:2010 Thermoplastics piping systems for non-pressure applications Test method for watertightness
ISO 13264:2010 Thermoplastics piping systems for non-pressure underground drainage and sewerage Thermoplastics fittings Test method for mechanical strength or flexibility of fabricated fittings
ISO 1043-1:2011 Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics
ISO 9969:2016 Thermoplastics pipes Determination of ring stiffness
EN 1565-1:1998 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN+PVC) - Part 1: Specifications for pipes, fittings and the system
ISO 1133:2005 Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
EN ISO 472:2013 Plastics - Vocabulary (ISO 472:2013)
EN ISO 1183-1:2012 Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012)
CEN/TS 14541:2013 Plastics pipes and fittings - Characteristics for utilisation of non-virgin PVC-U, PP and PE materials
ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method
ISO 2505:2005 Thermoplastics pipes — Longitudinal reversion — Test method and parameters

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.