EN 12668-2:2010
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Part 2: Probes
Superseded date
02-19-2022
Published date
02-03-2010
Publisher
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 General requirements for compliance
5 Technical specification for probes
6 Test equipment
7 Performance requirements for probes
Annex A (normative) - Calculation of near field length
of non-focusing probes
Annex B (informative) - Calibration block for angle-beam
probes
Bibliography
This European Standard covers probes used for ultrasonic non-destructive examination in the following categories with centre frequencies in the range 0,5 MHz to 15 MHz, focusing and without focusing means:a)single or dual transducer contact probes generating compressional or shear waves;b)single transducer immersion probes.Where material-dependent ultrasonic values are specified in this document they are based on steels having a sound velocity of (5 920 ± 50) m/s for longitudinal waves, and (3 255 ± 30) m/s for transverse waves.Periodic tests for probes are not included in this document. Routine tests for the verification of probes using on-site methods are given in EN 12668-3.If parameters in addition to those specified in EN 12668-3 are to be verified during the probe's life time, as agreed upon by the contracting parties, the methods of verification for these additional parameters should be selected from those given in this document.
| Committee |
CEN/TC 138
|
| DevelopmentNote |
Supersedes PREN 12668-2. (10/2005)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NF EN 12668-2 : 2010 | Identical |
| NBN EN 12668-2 : 2010 | Identical |
| NS EN 12668-2 : 2010 | Identical |
| UNE-EN 12668-2:2010 | Identical |
| UNI EN 12668-2 : 2010 | Identical |
| DIN EN 12668-2 E : 2010 | Identical |
| NEN EN 12668-2 : 2010 | Identical |
| I.S. EN 12668-2:2010 | Identical |
| BS EN 12668-2:2010 | Identical |
| DIN EN 12668-2:2010-06 | Identical |
| PN EN 12668-2 : 2010 | Identical |
| SN EN 12668-2 : 2010 | Identical |
| UNE-EN 15317:2014 | Non-destructive testing - Ultrasonic testing - Characterization and verification of ultrasonic thickness measuring equipment |
| 10/30198090 DC : 0 | BS EN ISO 13588 - NON-DESTRUCTIVE TESTING OF WELDS - ULTRASONIC TESTING - USE OF (SEMI-) AUTOMATED PHASED ARRAY TECHNOLOGY |
| UNI EN ISO 17405 : 2014 | NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING - TECHNIQUE OF TESTING CLADDINGS PRODUCED BY WELDING, ROLLING AND EXPLOSION |
| DIN EN ISO 16828:2014-06 | NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING - TIME-OF-FLIGHT DIFFRACTION TECHNIQUE AS A METHOD FOR DETECTION AND SIZING OF DISCONTINUITIES (ISO 16828:2012) |
| DIN EN 583-6:2009-03 | NON-DESTRUCTIVE TESTING - ULTRASONIC EXAMINATION - PART 6: TIME-OF-FLIGHT DIFFRACTION TECHNIQUE AS A METHOD FOR DETECTION AND SIZING OF DISCONTINUITIES |
| DIN EN 12668-3 E : 2014 | NON-DESTRUCTIVE TESTING - CHARACTERIZATION AND VERIFICATION OF ULTRASONIC EXAMINATION EQUIPMENT - PART 3: COMBINED EQUIPMENT |
| DIN EN ISO 16810 E : 2014 | NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING - GENERAL PRINCIPLES (ISO 16810:2012) |
| I.S. EN ISO 16828:2014 | ON-DESTRUCTIVE TESTING - ULTRASONIC TESTING - TIME-OF-FLIGHT DIFFRACTION TECHNIQUE AS A METHOD FOR DETECTION AND SIZING OF DISCONTINUITIES (ISO 16828:2012) |
| DIN EN ISO 17405 E : 2014 | NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING - TECHNIQUE OF TESTING CLADDINGS PRODUCED BY WELDING, ROLLING AND EXPLOSION (ISO 17405:2014) |
| DIN EN ISO 18563-3:2016-06 | NON-DESTRUCTIVE TESTING - CHARACTERIZATION AND VERIFICATION OF ULTRASONIC PHASED ARRAY EQUIPMENT - PART 3: COMBINED SYSTEMS (ISO 18563-3:2015) |
| 12/30270659 DC : 0 | BS EN 10228-3 - NON-DESTRUCTIVE TESTING OF STEEL FORGINGS - PART 3: ULTRASONIC TESTING OF FERRITIC OR MARTENSITIC STEEL FORGINGS |
| 17/30326176 DC : 0 | BS EN 16729-3 - RAILWAY APPLICATIONS - INFRASTRUCTURE - NON-DESTRUCTIVE TESTING ON RAILS IN TRACK - PART 3: REQUIREMENTS FOR IDENTIFYING INTERNAL AND SURFACE RAIL DEFECTS |
| 04/30123014 DC : DRAFT SEP 2004 | ISO 4992-2 - STEEL CASTINGS - ULTRASONIC EXAMINATION - PART 2: STEEL CASTINGS FOR HIGHLY STRESSED COMPONENTS |
| DD CEN/TS 14751:2004 | Welding. Use of time-of-flight diffraction technique (TOFD) for examination of welds |
| UNE-EN ISO 17405:2015 | Non-destructive testing - Ultrasonic testing - Technique of testing claddings produced by welding, rolling and explosion (ISO 17405:2014) |
| 07/30135963 DC : 0 | BS EN 1714 - NON-DESTRUCTIVE TESTING OF WELDS - ULTRASONIC TESTING OF WELDED JOINTS |
| ISO 16831:2012 | Non-destructive testing — Ultrasonic testing — Characterization and verification of ultrasonic thickness measuring equipment |
| I.S. EN ISO 16810:2014 | NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING - GENERAL PRINCIPLES (ISO 16810:2012) |
| BS EN 16910-1:2018 | Railway applications. Rolling stock. Requirements for non-destructive testing on running gear in railway maintenance Wheelsets |
| EN ISO 22825:2017 | NON-DESTRUCTIVE TESTING OF WELDS - ULTRASONIC TESTING - TESTING OF WELDS IN AUSTENITIC STEELS AND NICKEL-BASED ALLOYS (ISO 22825:2017) |
| EN 10228-3:2016 | Non-destructive testing of steel forgings - Part 3: Ultrasonic testing of ferritic or martensitic steel forgings |
| BS EN 10306:2002 | Iron and steel. Ultrasonic testing of H beams with parallel flanges and IPE beams |
| UNE-EN 12680-3:2012 | Founding - Ultrasonic testing - Part 3: Spheroidal graphite cast iron castings |
| BS EN 10307:2001 | Non-destructive testing. Ultrasonic testing of austenitic and austentitic-ferritic stainless steels flat products of thickness equal to or greater than 6 mm (reflection method) |
| DIN EN 13100-3:2005-02 | Non-destructive testing of welded joints in thermoplastics semi-finished products - Part 3: Ultrasonic testing |
| EN 12680-1:2003 | Founding - Ultrasonic examination - Part 1: Steel castings for general purposes |
| EN 10308:2001 | Non destructive testing - Ultrasonic testing of steel bars |
| EN 10306:2001 | Iron and steel - Ultrasonic testing of H beams with parallel flanges and IPE beams |
| EN 10307:2001 | Non-destructive testing - Ultrasonic testing of austenitic and austenitic-ferritic stainless steels flat products of thickness equal to or greater than 6 mm (reflection method) |
| DIN EN 12680-2:2003-06 | Founding - Ultrasonic examination - Part 2: Steel castings for highly stressed components; German version EN 12680-2:2003 |
| EN 12680-3:2011 | Founding - Ultrasonic testing - Part 3: Spheroidal graphite cast iron castings |
| DIN EN 10307:2002-03 | NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING OF AUSTENITIC AND AUSTENITIC-FERRITIC STAINLESS STEELS FLAT PRODUCTS OF THICKNESS EQUAL TO OR GREATER THAN 6 MM (REFLECTION METHOD) |
| EN 12680-2:2003 | Founding - Ultrasonic examination - Part 2: Steel castings for highly stressed components |
| DIN EN 12680-3:2012-02 | Founding - Ultrasonic testing - Part 3: Spheroidal graphite cast iron castings |
| CEN/TS 14751:2004 | Welding - Use of time-of-flight diffraction technique (TOFD) for examination of welds |
| EN 12668-3:2013 | Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Part 3: Combined equipment |
| EN 10228-4:2016 | Non-destructive testing of steel forgings - Part 4: Ultrasonic testing of austenitic and austenitic-ferritic stainless steel forgings |
| EN 13100-3:2004 | Non destructive testing of welded joints in thermoplastics semi-finished products - Part 3: Ultrasonic testing |
| UNI EN 16090 : 2012 | COPPER AND COPPER ALLOYS - ESTIMATION OF AVERAGE GRAIN SIZE BY ULTRASOUND |
| I.S. CEN TS 14751:2004 | WELDING - USE OF TIME-OF-FLIGHT DIFFRACTION TECHNIQUE (TOFD) FOR EXAMINATION OF WELDS |
| BS ISO 18610:2016 | Fine ceramics (advanced ceramics, advanced technical ceramics). Mechanical properties of ceramic composites at ambient temperature in air atmospheric pressure. Determination of elastic properties by ultrasonic technique |
| BS EN ISO 18563-3:2015 | NON-DESTRUCTIVE TESTING - CHARACTERIZATION AND VERIFICATION OF ULTRASONIC PHASED ARRAY EQUIPMENT - PART 3: COMBINED SYSTEMS |
| 10/30218967 DC : 0 | BS EN 12680-3 - FOUNDING - ULTRASONIC EXAMINATION - PART 3: SPHEROIDAL GRAPHITE CAST IRON CASTINGS |
| 12/30270662 DC : 0 | BS EN 10228-4 - NON-DESTRUCTIVE TESTING OF STEEL FORGINGS - PART 4: ULTRASONIC TESTING OF AUSTENITIC AND AUSTENITIC-FERRITIC STAINLESS STEEL FORGINGS |
| BS ISO 4992-2:2006 | Steel castings. Ultrasonic examination Steel castings for highly stressed components |
| UNI EN 583-6 : 2009 | NON-DESTRUCTIVE TESTING - ULTRASONIC EXAMINATION - PART 6: TIME-OF-FLIGHT DIFFRACTION TECHNIQUE AS A METHOD FOR DETECTION AND SIZING OF DISCONTINUITIES |
| PREN 10228-4 : DRAFT 2012 | NON-DESTRUCTIVE TESTING OF STEEL FORGINGS - PART 4: ULTRASONIC TESTING OF AUSTENITIC AND AUSTENITIC-FERRITIC STAINLESS STEEL FORGINGS |
| I.S. EN 16090:2011 | COPPER AND COPPER ALLOYS - ESTIMATION OF AVERAGE GRAIN SIZE BY ULTRASOUND |
| DIN EN 12680-3 E : 2012 | FOUNDING - ULTRASONIC TESTING - PART 3: SPHEROIDAL GRAPHITE CAST IRON CASTINGS |
| DIN EN 12680-2 E : 2003 | FOUNDING - ULTRASONIC EXAMINATION - PART 2: STEEL CASTINGS FOR HIGHLY STRESSED COMPONENTS |
| DIN EN 12680-1 E : 2003 | FOUNDING - ULTRASONIC EXAMINATION - PART 1: STEEL CASTINGS FOR GENERAL PURPOSES |
| DIN EN 15317 E : 2014 | NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING - CHARACTERIZATION AND VERIFICATION OF ULTRASONIC THICKNESS MEASURING EQUIPMENT |
| DIN EN 15317:2014-02 | NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING - CHARACTERIZATION AND VERIFICATION OF ULTRASONIC THICKNESS MEASURING EQUIPMENT |
| BS EN 10308:2002 | Non-destructive testing. Ultrasonic testing of steel bars |
| I.S. EN 10228-3:2016 | NON-DESTRUCTIVE TESTING OF STEEL FORGINGS - PART 3: ULTRASONIC TESTING OF FERRITIC OR MARTENSITIC STEEL FORGINGS |
| UNI EN 12668-3 : 2013 | NON-DESTRUCTIVE TESTING - CHARACTERIZATION AND VERIFICATION OF ULTRASONIC EXAMINATION EQUIPMENT - PART 3: COMBINED EQUIPMENT |
| I.S. EN 12668-3:2013 | NON-DESTRUCTIVE TESTING - CHARACTERIZATION AND VERIFICATION OF ULTRASONIC EXAMINATION EQUIPMENT - PART 3: COMBINED EQUIPMENT |
| I.S. EN 15317:2013 | NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING - CHARACTERIZATION AND VERIFICATION OF ULTRASONIC THICKNESS MEASURING EQUIPMENT |
| I.S. EN 10228-4:2016 | NON-DESTRUCTIVE TESTING OF STEEL FORGINGS - PART 4: ULTRASONIC TESTING OF AUSTENITIC AND AUSTENITIC-FERRITIC STAINLESS STEEL FORGINGS |
| I.S. EN 12680-3:2011 | FOUNDING - ULTRASONIC TESTING - PART 3: SPHEROIDAL GRAPHITE CAST IRON CASTINGS |
| 13/30277410 DC : 0 | BS EN 15317 - NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING - CHARACTERIZATION AND VERIFICATION OF ULTRASONIC THICKNESS MEASURING EQUIPMENT |
| DIN EN 12668-3:2014-02 | Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Part 3: Combined equipment |
| BS EN 16090:2011 | Copper and copper alloys. Estimation of average grain size by ultrasound |
| UNI EN ISO 16828 : 2014 | NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING - TIME-OF-FLIGHT DIFFRACTION TECHNIQUE AS A METHOD FOR DETECTION AND SIZING OF DISCONTINUITIES |
| DIN EN ISO 17405:2014-10 | Non-destructive testing - Ultrasonic testing - Technique of testing claddings produced by welding, rolling and explosion (ISO 17405:2014); German version EN ISO 17405:2014 |
| PREN 12799 : DRAFT 2017 | BRAZING - NON-DESTRUCTIVE EXAMINATION OF BRAZED JOINTS |
| 10/30195043 DC : 0 | BS EN ISO 22825 - NON-DESTRUCTIVE TESTING OF WELDS - ULTRASONIC TESTING - TESTING OF WELDS IN AUSTENITIC STEELS AND NICKEL-BASED ALLOYS |
| 18/30337971 DC : DRAFT APR 2018 | BS ISO 20890-1 - IN-SERVICE INSPECTIONS FOR PRIMARY COOLANT CIRCUIT COMPONENTS OF LIGHT WATER REACTORS - PART 1: MECHANIZED ULTRASONIC TESTING |
| DIN EN ISO 16828 E : 2014 | NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING - TIME-OF-FLIGHT DIFFRACTION TECHNIQUE AS A METHOD FOR DETECTION AND SIZING OF DISCONTINUITIES (ISO 16828:2012) |
| BS ISO 4992-1:2006 | Steel castings. Ultrasonic examination Steel castings for general purposes |
| DIN EN 16090:2012-02 | COPPER AND COPPER ALLOYS - ESTIMATION OF AVERAGE GRAIN SIZE BY ULTRASOUND |
| 04/30123011 DC : DRAFT SEP 2004 | ISO 4992-1 - STEEL CASTINGS - ULTRASONIC EXAMINATION - PART 1: STEEL CASTINGS FOR GENERAL PURPOSES |
| DIN EN ISO 16810:2014-07 | Non-destructive testing - Ultrasonic testing - General principles (ISO 16810:2012) |
| 16/30345944 DC : 0 | BS EN ISO 22825 - NON-DESTRUCTIVE TESTING OF WELDS - ULTRASONIC TESTING - TESTING OF WELDS IN AUSTENITIC STEELS AND NICKEL-BASED ALLOYS |
| I.S. EN 583-6:2008 | NON-DESTRUCTIVE TESTING - ULTRASONIC EXAMINATION - PART 6: TIMEOF- FLIGHT DIFFRACTION TECHNIQUE AS A METHOD FOR DETECTION AND SIZING OF DISCONTINUITIES |
| UNE-EN ISO 16828:2014 | Non-destructive testing - Ultrasonic testing - Time-of-flight diffraction technique as a method for detection and sizing of discontinuities (ISO 16828:2012) |
| ISO 22825:2017 | Non-destructive testing of welds — Ultrasonic testing — Testing of welds in austenitic steels and nickel-based alloys |
| UNE-EN 10228-4:2016 | Non-destructive testing of steel forgings - Part 4: Ultrasonic testing of austenitic and austenitic-ferritic stainless steel forgings |
| UNE-EN 10228-3:2016 | Non-destructive testing of steel forgings - Part 3: Ultrasonic testing of ferritic or martensitic steel forgings |
| BS EN 12680-3:2011 | Founding. Ultrasonic testing Spheroidal graphite cast iron castings |
| UNE-EN 16090:2012 | Copper and copper alloys - Estimation of average grain size by ultrasound |
| UNI EN 15317 : 2013 | NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING - CHARACTERIZATION AND VERIFICATION OF ULTRASONIC THICKNESS MEASURING EQUIPMENT |
| UNI EN 12680-3 : 2012 | FOUNDING - ULTRASONIC TESTING - PART 3: SPHEROIDAL GRAPHITE CAST IRON CASTINGS |
| 15/30270299 DC : 0 | BS EN 16910 - RAILWAY APPLICATIONS - ROLLING STOCK - REQUIREMENTS FOR NONDESTRUCTIVE TESTING ON RUNNING GEAR IN RAILWAY MAINTENANCE |
| 15/30280621 DC : 0 | BS ISO 18610 - FINE CERAMICS (ADVANCED CERAMICS, ADVANCED TECHNICAL CERAMICS) - MECHANICAL PROPERTIES OF CERAMIC COMPOSITES AT ROOM TEMPERATURE - DETERMINATION OF ELASTIC PROPERTIES BY AN ULTRASONIC TECHNIQUE |
| PREN 12668-3 : DRAFT 2013 | NON-DESTRUCTIVE TESTING - CHARACTERIZATION AND VERIFICATION OF ULTRASONIC EXAMINATION EQUIPMENT - PART 3: COMBINED EQUIPMENT |
| BS EN 583-6:2008 | Non-destructive testing. Ultrasonic examination Time-of-flight diffraction technique as a method for detection and sizing of discontinuities |
| BS EN ISO 16828:2014 | Non-destructive testing. Ultrasonic testing. Time-of-flight diffraction technique as a method for detection and sizing of discontinuities |
| I.S. EN 16910-1:2018 | RAILWAY APPLICATIONS - ROLLING STOCK - REQUIREMENTS FOR NON-DESTRUCTIVE TESTING ON RUNNING GEAR IN RAILWAY MAINTENANCE - PART 1: WHEELSETS |
| DD ENV 583-6:2000 | Non-destructive testing. Ultrasonic examination Time-of-flight diffraction technique as a method for detection and sizing of discontinuities |
| 03/115417 DC : DRAFT SEP 2003 | BS EN ISO 22825 - NON-DESTRUCTIVE TESTING OF WELDS - ULTRASONIC METHOD - TESTING OF WELDS IN AUSTENITIC STEELS AND NICKEL BASED ALLOYS |
| PREN 10228-3 : DRAFT 2012 | NON-DESTRUCTIVE TESTING OF STEEL FORGINGS - PART 3: ULTRASONIC TESTING OF FERRITIC OR MARTENSITIC STEEL FORGINGS |
| ISO 12715:2014 | Non-destructive testing Ultrasonic testing Reference blocks and test procedures for the characterization of contact probe sound beams |
| EN 16910-1:2018 | Railway applications - Rolling stock - Requirements for non-destructive testing on running gear in railway maintenance - Part 1: Wheelsets |
| BS EN ISO 22825:2017 | Non-destructive testing of welds. Ultrasonic testing. Testing of welds in austenitic steels and nickel-based alloys |
| KTA 3211.1 : 2015 | PRESSURE AND ACTIVITY RETAINING COMPONENTS OF SYSTEMS OUTSIDE THE PRIMARY CIRCUIT - PART 1: MATERIALS |
| ISO 4992-1:2006 | Steel castings Ultrasonic examination Part 1: Steel castings for general purposes |
| I.S. EN ISO 22825:2017 | NON-DESTRUCTIVE TESTING OF WELDS - ULTRASONIC TESTING - TESTING OF WELDS IN AUSTENITIC STEELS AND NICKEL-BASED ALLOYS (ISO 22825:2017) |
| UNE-EN 12668-3:2014 | Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Part 3: Combined equipment |
| DIN EN 10228-4:2016-10 | NON-DESTRUCTIVE TESTING OF STEEL FORGINGS - PART 4: ULTRASONIC TESTING OF AUSTENITIC AND AUSTENITIC-FERRITIC STAINLESS STEEL FORGINGS |
| DIN EN 10228-3:2016-10 | NON-DESTRUCTIVE TESTING OF STEEL FORGINGS - PART 3: ULTRASONIC TESTING OF FERRITIC OR MARTENSITIC STEEL FORGINGS |
| ISO 16810:2012 | Non-destructive testing — Ultrasonic testing — General principles |
| BS EN 12680-1:2003 | Founding. Ultrasonic examination Steel castings for general purposes |
| BS EN 12680-2:2003 | Founding. Ultrasonic examination Steel castings for highly stressed components |
| BS EN 15317:2013 | Non-destructive testing. Ultrasonic testing. Characterization and verification of ultrasonic thickness measuring equipment |
| BS EN 10228-4:2016 | Non-destructive testing of steel forgings Ultrasonic testing of austenitic and austenitic-ferritic stainless steel forgings |
| BS EN 13100-3:2004 | Non-destructive testing of welded joints in thermoplastics semi-finished products Ultrasonic testing |
| UNE-EN ISO 16810:2014 | Non-destructive testing - Ultrasonic testing - General principles (ISO 16810:2012) |
| UNE-EN ISO 18563-3:2016 | Non-destructive testing - Characterization and verification of ultrasonic phased array equipment - Part 3: Combined systems (ISO 18563-3:2015) |
| BS EN 10228-3:2016 | Non-destructive testing of steel forgings Ultrasonic testing of ferritic or martensitic steel forgings |
| ISO 18563-3:2015 | Non-destructive testing Characterization and verification of ultrasonic phased array equipment Part 3: Combined systems |
| ISO 16828:2012 | Non-destructive testing — Ultrasonic testing — Time-of-flight diffraction technique as a method for detection and sizing of discontinuities |
| EN ISO 16810:2014 | Non-destructive testing - Ultrasonic testing - General principles (ISO 16810:2012) |
| EN ISO 18563-3:2015 | Non-destructive testing - Characterization and verification of ultrasonic phased array equipment - Part 3: Combined systems (ISO 18563-3:2015) |
| EN 15317:2013 | Non-destructive testing - Ultrasonic testing - Characterization and verification of ultrasonic thickness measuring equipment |
| EN 16090:2011 | Copper and copper alloys - Estimation of average grain size by ultrasound |
| EN ISO 17405:2014 | Non-destructive testing - Ultrasonic testing - Technique of testing claddings produced by welding, rolling and explosion (ISO 17405:2014) |
| EN 16729-3:2018 | Railway applications - Infrastructure - Non-destructive testing on rails in track - Part 3: Requirements for identifying internal and surface rail defects |
| EN ISO 16828:2014 | Non-destructive testing - Ultrasonic testing - Time-of-flight diffraction technique as a method for detection and sizing of discontinuities (ISO 16828:2012) |
| EN 583-6:2008 | Non-destructive testing - Ultrasonic examination - Part 6: Time-of-flight diffraction technique as a method for detection and sizing of discontinuities |
| UNE-EN 583-6:2010 | Non-destructive testing - Ultrasonic examination - Part 6: Time-of-flight diffraction technique as a method for detection and sizing of discontinuities |
| DIN EN ISO 18563-3 E : 2016 | NON-DESTRUCTIVE TESTING - CHARACTERIZATION AND VERIFICATION OF ULTRASONIC PHASED ARRAY EQUIPMENT - PART 3: COMBINED SYSTEMS (ISO 18563-3:2015) |
| I.S. EN ISO 17405:2014 | NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING - TECHNIQUE OF TESTING CLADDINGS PRODUCED BY WELDING, ROLLING AND EXPLOSION (ISO 17405:2014) |
| 09/30187580 DC : DRAFT SEP 2009 | BS EN ISO 10863 - WELDING - USE OF TIME-OF-FLIGHT DIFFRACTION TECHNIQUE (TOFD) FOR TESTING OF WELDS |
| 13/30277407 DC : 0 | BS EN 12668-3 - NON-DESTRUCTIVE TESTING - CHARACTERIZATION AND VERIFICATION OF ULTRASONIC EXAMINATION EQUIPMENT - PART 3: COMBINED EQUIPMENT |
| BS EN ISO 17405:2014 | Non-destructive testing. Ultrasonic testing. Technique of testing claddings produced by welding, rolling and explosion |
| BS EN ISO 16810:2014 | Non-destructive testing. Ultrasonic testing. General principles |
| PREN 12680-3 : DRAFT 2010 | FOUNDING - ULTRASONIC EXAMINATION - PART 3: SPHEROIDAL GRAPHITE CAST IRON CASTINGS |
| I.S. EN ISO 18563-3:2015 | NON-DESTRUCTIVE TESTING - CHARACTERIZATION AND VERIFICATION OF ULTRASONIC PHASED ARRAY EQUIPMENT - PART 3: COMBINED SYSTEMS (ISO 18563-3:2015) |
| ISO 18610:2016 | Fine ceramics (advanced ceramics, advanced technical ceramics) Mechanical properties of ceramic composites at ambient temperature in air atmospheric pressure Determination of elastic properties by ultrasonic technique |
| ISO 4992-2:2006 | Steel castings Ultrasonic examination Part 2: Steel castings for highly stressed components |
| I.S. EN 16729-3:2018 | RAILWAY APPLICATIONS - INFRASTRUCTURE - NON-DESTRUCTIVE TESTING ON RAILS IN TRACK - PART 3: REQUIREMENTS FOR IDENTIFYING INTERNAL AND SURFACE RAIL DEFECTS |
| 17/30359544 DC : 0 | BS EN 12799 - BRAZING - NON-DESTRUCTIVE EXAMINATION OF BRAZED JOINTS |
| UNI EN ISO 16810 : 2014 | NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING - GENERAL PRINCIPLES |
| KTA 3201.3 : 2007(R2012) | COMPONENTS OF THE REACTOR COOLANT PRESSURE BOUNDARY OF LIGHT WATER REACTORS - PART 3: MANUFACTURE |
| BS EN 12668-3:2013 | Non-destructive testing. Characterization and verification of ultrasonic examination equipment Combined equipment |
| ISO 17405:2014 | Non-destructive testing Ultrasonic testing Technique of testing claddings produced by welding, rolling and explosion |
| DIN EN 10228-3:1998-07 | NON-DESTRUCTIVE TESTING OF STEEL FORGINGS - PART 3: ULTRASONIC TESTING OF FERRITIC OR MARTENSITIC STEEL FORGINGS |
| DIN EN 10228-4:1999-10 | NON-DESTRUCTIVE TESTING OF STEEL FORGINGS - PART 4: ULTRASONIC TESTING OF AUSTENITIC AND AUSTENITIC-FERRITIC STAINLESS STEEL FORGINGS |
| DIN EN 10306:2002-04 | IRON AND STEEL - ULTRASONIC TESTING OF H BEAMS WITH PARALLEL FLANGES AND IPE BEAMS |
| DIN EN 12680-1:2003-06 | Founding - Ultrasonic examination - Part 1: Steel castings for general purposes; German version EN 12680-1:2003 |
| DIN EN 10308:2002-03 | NON-DESTRUCTIVE TESTING - ULTRASONIC TESTING OF STEEL BARS |
| EN ISO 7963:2010 | Non-destructive testing - Ultrasonic testing - Specification for calibration block No. 2 (ISO 7963:2006) |
| ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
| EN 1330-4:2010 | Non-destructive testing - Terminology - Part 4: Terms used in ultrasonic testing |
| EN 12668-1:2010 | Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Part 1: Instruments |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN 12668-3:2013 | Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Part 3: Combined equipment |
| ISO 7963:2006 | Non-destructive testing — Ultrasonic testing —- Specification for calibration block No. 2 |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.